scholarly journals Multiscale Copper-µDiamond Nanostructured Composites

2012 ◽  
Vol 730-732 ◽  
pp. 925-930
Author(s):  
Daniela Nunes ◽  
Vanessa Livramento ◽  
Horácio Fernandes ◽  
Carlos Silva ◽  
Nobumitsu Shohoji ◽  
...  
Keyword(s):  
Pure Copper ◽  
Thermal Stabilization ◽  
Hot Extrusion ◽  
Processing Parameters ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Optimal Processing ◽  
Novel Approach ◽  
Transmission Electron

Nanostructured copper-diamond composites can be tailored for thermal management applications at high temperature. A novel approach based on multiscale diamond dispersions is proposed for the production of this type of materials: a Cu-nDiamond composite produced by high-energy milling is used as a nanostructured matrix for further dispersion of micrometer sized diamond. The former offers strength and microstructural thermal stability while the latter provides high thermal conductivity. A series of Cu-nDiamond mixtures have been milled to define the minimum nanodiamond fraction suitable for matrix refinement and thermal stabilization. A refined matrix with homogenously dispersed nanoparticles could be obtained with 4 at.% nanodiamond for posterior mixture with mDiamond and subsequent consolidation. In order to define optimal processing parameters, consolidation by hot extrusion has been carried out for a Cu-nDiamond composite and, in parallel, for a mixture of pure copper and mDiamond. The materials produced were characterized by X-ray diffraction, scanning and transmission electron microscopy and microhardness measurements.

Effect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy Powders

2010 ◽  
Vol 654-656 ◽  
pp. 1106-1109
Author(s):  
Ya Qiong He ◽  
Chang Hui Mao ◽  
Jian Yang
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Alloy Powder ◽  
High Energy ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron ◽  
Nitridation Temperature ◽  
Microstructure And Magnetic Properties

Nanocrystalline Fe-Co alloy powders, which were prepared by high-energy mechanical milling, were nitrided under the mixing gas of NH3/H2 in the temperature range from 380°C to 510°C. X-ray diffraction (XRD) was used to analyze the grain size and reaction during the processing. The magnetic properties of the nitrided powders were measured by Vibrating Sample Magnetometer (VSM). The results show that with the appearance of Fe4N phase after nitride treatment, and the grain-size of FeCo phase decreases with the increase of nitridation temperature between 380°C to 450°C.The saturation magnetization of nitrided alloy powder treated at 480°C is about 18% higher than that of the initial Fe-Co alloy powder, accompanied by the reduction of the coercivity. Transmission electron microscope (TEM) was used, attempting to further analyze the effect of Fe4N phase on microstructure and magnetic properties of the powder mixtures.

Structural changes in titanium dioxide nanocrystals during plastic deformation

2005 ◽  
Vol 38 (5) ◽  
pp. 749-756 ◽  
Author(s):  
Ulrich Gesenhues
Keyword(s):  
Structural Changes ◽  
Crystal Size ◽  
Lower Layer ◽  
High Energy ◽  
Primary Crystal ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Hall Method ◽  
Means Of Transmission

The polygonization of 200 nm rutile crystals during dry ball-milling at 10gwas monitored in detail by means of transmission electron microscopy (TEM) and X-ray diffraction (XRD). The TEM results showed how to modify the Williamson–Hall method for a successful evaluation of crystal size and microstrain from XRD profiles. Macrostrain development was determined from the minute shift of the most intense reflection. In addition, changes in pycnometrical density were monitored. Accordingly, the primary crystal is disintegrated during milling into a mosaic of 12–35 nm pieces where the grain boundaries induce up to 1.2% microstrain in a lower layer of 6 nm thickness. Macrostrain in the interior of the crystals rises to 0.03%. The pycnometrical density, reflecting the packing density of atoms in the grain boundary, decreases steadily by 1.1%. The results bear relevance to our understanding of plastic flow and the mechanism of phase transitions of metal oxides during high-energy milling.

scholarly journals Structural Evolution in Wet Mechanically Alloyed Co-Fe-(Ta,W)-B Alloys

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 800
Author(s):  
Vladimír Girman ◽  
Maksym Lisnichuk ◽  
Daria Yudina ◽  
Miloš Matvija ◽  
Pavol Sovák ◽  
...  
Keyword(s):  
Structural Changes ◽  
Magnetic Measurements ◽  
Structural Evolution ◽  
High Energy ◽  
Control Agent ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
X Ray ◽  
Transmission Electron ◽  
X Ray Absorption

In the present study, the effect of wet mechanical alloying (MA) on the glass-forming ability (GFA) of Co43Fe20X5.5B31.5 (X = Ta, W) alloys was studied. The structural evolution during MA was investigated using high-energy X-ray diffraction, X-ray absorption spectroscopy, high-resolution transmission electron microscopy and magnetic measurements. Pair distribution function and extended X-ray absorption fine structure spectroscopy were used to characterize local atomic structure at various stages of MA. Besides structural changes, the magnetic properties of both compositions were investigated employing a vibrating sample magnetometer and thermomagnetic measurements. It was shown that using hexane as a process control agent during wet MA resulted in the formation of fully amorphous Co-Fe-Ta-B powder material at a shorter milling time (100 h) as compared to dry MA. It has also been shown that substituting Ta with W effectively suppresses GFA. After 100 h of MA of Co-Fe-W-B mixture, a nanocomposite material consisting of amorphous and nanocrystalline bcc-W phase was synthesized.

Characterization of the Phase Transformations in the Shape Memory Alloy Ni-36 at.% Al

1991 ◽  
Vol 246 ◽  
Author(s):  
J.A. Horton ◽  
E.P. George ◽  
C.J. Sparks ◽  
M.Y. Kao ◽  
O.B. Cavin ◽  
...  
Keyword(s):  
High Temperature ◽  
Shape Memory ◽  
Phase Transformations ◽  
Hot Extrusion ◽  
Exothermic Peak ◽  
Nickel Aluminum ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron

AbstractA survey by differential scanning calorimetry (DSC) and recovery during heating of indentations on a series of nickel-aluminum alloys showed that the Ni-36 at.% Al composition has the best potential for a recoverable shape memory effect at temperatures above 100°C. The phase transformations were studied by high temperature transmission electron microscopy (TEM) and by high temperature x-ray diffraction (HTXRD). Quenching from 1200°C resulted in a single phase, fully martensitic structure. The initial quenched-in martensites were found by both TEM and X-ray diffraction to consist of primarily a body centered tetragonal (bct) phase with some body centered orthorhombic (bco) phase present. On the first heating cycle, DSC showed an endothermic peak at 121°C and an exothermic peak at 289°C, and upon cooling a martensite exothermic peak at 115° C. Upon subsequent cycles the 289°C peak disappeared. High temperature X-ray diffraction, with a heating rate of 2°C/min, showed the expected transformation of bct phase to B2 between 100 and 200°C, however the bco phase remained intact. At 400 to 450°C the B2 phase transformed to Ni2Al and Ni5Al3. During TEM heating experiments a dislocation-free martensite transformed reversibly to B2 at temperatures less than 150°C. At higher temperatures (nearly 600°C) 1/3, 1/3, 1/3 reflections from an ω-like phase formed. Upon cooling, the 1/3, 1/3, 1/3 reflections disappeared and a more complicated martensite resulted. Boron additions suppressed intergranular fracture and, as expected, resulted in no ductility improvements. Boron additions and/or hot extrusion encouraged the formation of a superordered bct structure with 1/2, 1/2, 0 reflections.

Epitaxial growth of BaO and SrO with new crystal structures using mass-separated low-energy O+ beams

1993 ◽  
Vol 8 (2) ◽  
pp. 321-323 ◽  
Author(s):  
Ryusuke Kita ◽  
Takashi Hase ◽  
Hiromi Takahashi ◽  
Kenichi Kawaguchi ◽  
Tadataka Morishita
Keyword(s):  
Lattice Constant ◽  
High Energy ◽  
Low Energy ◽  
Diffraction Reflection ◽  
High Energy Electron ◽  
Bulk Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Cubic Structure

The growth of BaO and SrO on SrTiO3(100) substrates using mass-separated low-energy (50 eV) O+ beams has been studied using x-ray diffraction, reflection high-energy electron diffraction, and high-resolution transmission electron microscopy. It was found that the BaO and SrO films have been epitaxially grown with new structures different from those of corresponding bulk crystals: The BaO films have a cubic structure with a lattice constant of 4.0 Å, and the SrO films have a tetragonal structure with a lattice constant of a = 3.7 Å parallel to the substrate and with c = 4.0 Å normal to the substrate.

Appropriate Conditions for Preparation of Nanosized WO3 through High-Energy-Milling

2011 ◽  
Vol 194-196 ◽  
pp. 665-668
Author(s):  
Chun Huan Chen ◽  
Rui Ming Ren
Keyword(s):  
Grain Size ◽  
Milling Time ◽  
Rotation Speed ◽  
Processing Parameters ◽  
High Energy ◽  
Charge Ratio ◽  
Activation Process ◽  
X Ray Diffraction ◽  
High Energy Milling ◽  
Transmission Electron

In order to synthesize WC-Co nanopowders through an integrated mechanical and thermal activation process, WO3-Co2O3-C nanopowders need to be obtained first. It is critical how to obtain the WO3-Co2O3-C nanopowders efficiently. The effect of processing parameters on the grain size during high-energy-milling of WO3-Co2O3-C mixed powders was studied via X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results show that the grain size of reactants can be effectively decreased with increasing the milling time, rotation speed, and charge ratio. After a certain time milling, both WO3 and C powders achieve nano-level in grain size and mixed homogeneously. The appropriate milling parameters for fabricating nanosized WO3+C+Co2O3 powders are suggested to be 4 to 8 hours of milling time, 400 RPM of rotation speed, and 40:1 to 60:1 of charge ratio.

Mechanism of Achieving Nanocrystalline AIRu By Ball Milling

1988 ◽  
Vol 132 ◽  
Author(s):  
E. Hellstern ◽  
H. J. Fecht ◽  
C. Garland ◽  
W. L. Johnson ◽  
W. M. Keck
Keyword(s):  
Ball Milling ◽  
Crystal Size ◽  
Shear Bands ◽  
Nanocrystalline Structure ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Energy Ball ◽  
Small Grains

ABSTRACTWe investigated through X- ray diffraction and transmission electron microscopy the crystal refinement of the intermetallic compound AIRu by high- energy ball milling. The deformation process causes a decrease of crystal size to 5–7 rum and an increase of atomic level strain. This deformation is localized in shear bands with a thickness of 0.5 to 1 micron. Within these bands the crystal lattice breaks into small grains with a typical size of 8–14 rum. Further deformation leads to a final nanocrystalline structure with randomly oriented crystallite grains separated by high- angle grain boundaries.

Mechanosynthesis of La0.95Sr0.05Ga0.90Mg0.10O3-δ

2008 ◽  
Vol 587-588 ◽  
pp. 931-935
Author(s):  
Priscila Gonçalves ◽  
Filipe M. Figueiredo
Keyword(s):  
Perovskite Phase ◽  
Average Crystallite Size ◽  
High Energy ◽  
Equivalent Diameter ◽  
Mass Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Planetary Rotation ◽  
Transmission Electron ◽  
Size Estimates

The production of La0.95Sr0.05Ga0.90Mg0.10O3-δ powders was achieved at room temperature by a mechanosynthesis route in a high energy planetary ball mill starting from a mixture of lanthanum, strontium, gallium and magnesium oxides. The milling was carried out in nylon containers, using zirconia balls and a balls:powder mass ratio of 10:1. The planetary rotation was kept constant at 650 rotations per minute (rpm), and the container at 1300 rpm, in the opposite direction. The formation of the perovskite phase was detected from the early milling stages and nearly completed after milling for 360 min, as shown by powder X-ray diffraction. Transmission electron microscopy results revealed that powders consist of agglomerates of homogeneous, crystalline particles with an average equivalent diameter of about 16-17 nm, in excellent agreement with average crystallite size estimates obtained from X-ray diffraction.

Characterization Techniques For Laser-Annealed Polysilicon on Insulating Layers

1980 ◽  
Vol 1 ◽  
Author(s):  
J. T. Schott ◽  
J. J. Comer
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Energy ◽  
High Energy Electron ◽  
X Ray Diffraction ◽  
X Ray ◽  
Characterization Techniques ◽  
Cw Laser ◽  
Transmission Electron ◽  
Scanning Electron

ABSTRACTVarious characterization techniques are applied to pulsed and cw laser-annealed polysilicon layers deposited on oxide layers. The results are used to compare these techniques as to the type and completeness of information provided, as well as sample preparation requirements and general ease or difficulty of measurement. The techniques employed include scanning electron microscopy (SEM), electron channeling micrographs and selected area channeling patterns (SACP), reflection (high energy) electron diffraction (RHEED), transmission electron microscopy (TEM) and selected area diffraction (SAD), x-ray diffraction, optical techniques and etching techniques.

Sign in / Sign up

Export Citation Format

Share Document