Treatment of Weak Foundation Based on the Cast-in-Place Expanded Pile of Construction Waste

2011 ◽  
Vol 243-249 ◽  
pp. 2759-2761
Author(s):  
Hua Qiang Liu ◽  
Xiao Yi Fan
Keyword(s):  
Mechanism Design ◽  
Raw Materials ◽  
Social Benefits ◽  
Construction Technology ◽  
Construction Waste ◽  
Foundation Treatment ◽  
Dynamic Replacement ◽  
The Cost ◽  
Design Construction

There were better economic and social benefits which the construction wastes were the raw materials of weak foundation treatment. The cast-in-place expanded piles of construction waste showed the advantages of the dynamic replacement and compaction replacement. In the paper, the mechanism, design, construction technology and inspection of weak foundation treatment were studied. The result showed that the cast-in-place expanded piles of construction waste not only could save the cost in the waste transportation, but also decrease the cost in the foundation reinforcement and avoid the land contamination.

scholarly journals Study on the technology of grouting and reinforcing the foundation of a railway bridge above shallow old mine goaf

2018 ◽  
Vol 169 ◽  
pp. 01041
Author(s):  
Hui-Quan Sui ◽  
Chun-Yuan Bait
Keyword(s):  
Fast Track ◽  
Construction Technology ◽  
Construction Site ◽  
Railway Bridge ◽  
Foundation Treatment ◽  
Pressure Grouting ◽  
Dip Angle ◽  
Bridge Foundation ◽  
The City ◽  
Design Construction

The city fast track railway bridge studied in this paper is located above an old mined out area. There is a 1500m2 underground goaf in the construction site with a depth of 30.8~53.2m, the seam thickness is 2.0~2.5m and the dip angle is 50~63 degrees. Although the mine has been abandoned for many years, there are still a lot of underground cavities. Collapse pits occurred on the surface occasionally till this day, especially during the rainy season. In order to make the design safe and reliable, drilling pressure grouting technique is proposed to fill and reinforce the foundation of the site. Proposed technique is tested by several experiments in simulated underground mined out area for the foundation treatment. The technical design, construction technology, grouting and reinforcement effect of the project are studied and summarized. The results of the experiment showed a stable and safe bridge foundation has been achieved. The proposed technique was then applied to on site experiment and pasted all tests.

Increasing the Capacity of Concrete Column with Integrated Permanent Formwork Using Wood-Wool Cement Board

2013 ◽  
Vol 325-326 ◽  
pp. 1305-1309 ◽  
Author(s):  
Nursafarina Ahmad ◽  
Zakiah Ahmad ◽  
Azerai Ali Rahman ◽  
Hanizah Abdul Hamid ◽  
Mohd Azrizal Aziz Fauzi
Keyword(s):  
Compressive Strength ◽  
Failure Modes ◽  
Construction Materials ◽  
Concrete Column ◽  
Construction Technology ◽  
Construction Waste ◽  
Permanent Formwork ◽  
Technology Process ◽  
The Cost ◽  
Cement Board

Growing construction activities requires increase in construction materials. The conventional method of constructions results in a rise in construction waste. Formwork as a main factor to generate construction waste has been the topic of investigation. The permanent formwork has been introduced with the aim to: promote the construction technology process that put quality, safety and environment issues into account, reduce the cost of workers and reduce the overall time of construction project. At present the permanent formwork available in the market are made from steel, and plastic and the cost is still high. Therefore this study is looking at the potential of commercial wood-wool cement board (WWCB) as permanent formwork. A series of concrete columns were constructed with and without integrated WWCB with different configurations of WWCB as permanent formwork. These columns were subjected to axial load and the compressive strength and failure modes were recorded. The results show that the present of permanent formwork from WWCB improves the compressive strength of the column. With the permanent formwork, the size of concrete column can be reduced and able to support the same load as column without permanent formwork. Therefore this construction method can reduce the overall cost of construction.

Prevent Fabricated Floor Slit Cracking Construction Technology

2012 ◽  
Vol 193-194 ◽  
pp. 1334-1337
Author(s):  
Yi Liu
Keyword(s):  
Economic Benefits ◽  
Construction Method ◽  
Social Benefits ◽  
Construction Technology ◽  
New Construction ◽  
The Cost

This paper adopts new construction method, fundamentally resolves and prevent the fabricated floor seam cracking phenomenon, save the cost and produce the obvious economic benefits and social benefits.

SELISIH BIAYA PRODUKSI SEBAGAI ALAT PENGENDALIAN MANAJEMEN PT INDO PUSAKA BERAU

2019 ◽  
Vol 3 (02) ◽  
pp. 397
Author(s):  
SAFITRI NURHIDAYATI ◽  
RIZKI AMELYA SYAM
Keyword(s):  
Raw Materials ◽  
Field Research ◽  
Analytical Tool ◽  
Production Costs ◽  
Raw Material ◽  
Labor Costs ◽  
Material Costs ◽  
Library Research ◽  
The Difference ◽  
The Cost

This study aims to analyze whether the difference that occurs in the cost of raw materials, direct labor, and factory overhead costs between the standard costs and the actual costs in PLTU LATI is a difference that is favorable or unfavorable. Data collection techniques with field research and library research. The analytical tool used is the analysis of the difference in raw material costs, the difference in direct labor costs and the difference in factory overhead costs. The hypothesis in this study is that the difference allegedly occurs in the cost of raw materials, direct labor costs, and factory overhead costs at PT Indo Pusaka Berau Tanjung Redeb is a favorable difference. The results showed that the difference in the cost of producing MWh electricity at PT Indo Pusaka Berau Tanjung Redeb in 2018, namely the difference in the price of raw material costs Rp. 548,029.80, - is favorable, the difference in quantity of raw materials is Rp. 957,216,602, - is (favorable) , the difference in direct labor costs Rp 2,602,642,084, - is (unfavorable), and the difference in factory overhead costs Rp 8,807,051,422, - is (favorable) This shows that the difference in the overall production cost budget is favorable or profitable. This beneficial difference shows that the company is really able to reduce production costs optimally in 2018.  

scholarly journals Overcoming Adverse Selection: How Public Intervention Can Restore Market Functioning

2012 ◽  
Vol 102 (1) ◽  
pp. 29-59 ◽  
Author(s):  
Jean Tirole
Keyword(s):  
Mechanism Design ◽  
Adverse Selection ◽  
Welfare Cost ◽  
Public Intervention ◽  
The Government ◽  
The Cost

The paper provides a first analysis of market jump starting and its two-way interaction between mechanism design and participation constraints. The government optimally overpays for the legacy assets and cleans up the market of its weakest assets, through a mixture of buybacks and equity injections, and leaves the firms with the strongest legacy assets to the market. The government reduces adverse selection enough to let the market rebound, but not too much, so as to limit the cost of intervention. The existence of a market imposes no welfare cost. (JEL D82, D83, G01, G31, H81)

scholarly journals Application of temporary reinforcement technology in insufficient construction of the understructure bearing capacity of viaduct

2019 ◽  
Vol 136 ◽  
pp. 04080
Author(s):  
Guohui Cao ◽  
Reqiang Liu ◽  
Jing Liu ◽  
Xiang Gao ◽  
Peng Wang
Keyword(s):  
Bearing Capacity ◽  
Three Dimensional ◽  
Social Benefits ◽  
Construction Technology ◽  
Project Cost ◽  
Special Cases ◽  
Project Construction ◽  
Lower Structure ◽  
Traditional Construction

The complex three-dimensional traffic construction often occur when the lower structure cannot bear the construction load and other special cases, indicating the need for temporary reinforcement of the lower structure. In this paper, combined with a project construction example, various temporary reinforcement technologies are adopted to solve the insufficient bearing capacity during understructure construction, which poses a serious danger, to ensure synchronous construction of the understructure and viaduct. Compared with the traditional construction technology, the temporary reinforcement technology proposed in this paper features the advantages of saving project cost and time and has achieved better economic and social benefits.

Key Technique on the Process Control for Construction of Hohhot Circle Expressway Asphalt Pavements

2012 ◽  
Vol 256-259 ◽  
pp. 1748-1753
Author(s):  
Bin Zhao ◽  
Pei Wen Hao
Keyword(s):  
Inner Mongolia ◽  
Raw Materials ◽  
Asphalt Pavement ◽  
Load Capacity ◽  
Asphalt Mixture ◽  
Natural Increase ◽  
Rigid Base ◽  
Construction Technology ◽  
Pavement Structure ◽  
Major Section

As vehicle flow on arterial highway in Inner Mongolia sharply increased, the originally designed natural increase rate of 8% per year has been exceeded on the vehicle flow in some sections. According to statistics, monthly average vehicle flow on major section of G6 expressway has reached a standard flow of 67478 vehicles per day and night, of which in 70-80% are large ones for coal transportation. Therefore, pavement load and road capacity have exceed the designed expressway load capacity. At present, semi-rigid base asphalt pavement structure is still widely used for high-grade highway pavement in Inner Mongolia. With years of construction for such pavement structure, a great deal of valuable experience has been gained on construction technology. However, there are still a few deficiencies in the quality of raw materials, gradation control of asphalt mixture and adjustment of equipment, etc. Hohhot circle expressway connects with the G6 and G7 expressways, suffering from problems such as large vehicle flow and load overweight. This paper introduced a key technique that should be properly controlled during construction of such pavement structure, emphasized technique control and management of the following aspects, i.e. ballast sizes and gradation control, asphalt concrete mixture, adjustment of pavers, validation of mixing proportion in production and reasonable arrangement of process, and summarized corresponding technical measures taken during construction of asphalt pavement in this project.

Use of Sugarcane Bagasse Ashes as Raw Material in the Replacement of Fluxes for Applications on Porcelain Tile

2016 ◽  
Vol 881 ◽  
pp. 383-386 ◽  
Author(s):  
Raimundo J.S. Paranhos ◽  
Wilson Acchar ◽  
Vamberto Monteiro Silva
Keyword(s):  
Mechanical Properties ◽  
Environmental Impact ◽  
Physical Properties ◽  
Sugarcane Bagasse ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Raw Material ◽  
The Cost ◽  
Potential Use ◽  
Porcelain Tile

This study evaluated the potential use of Sugarcane Bagasse Ashes (SBA) as a flux, replacing phyllite for the production of enamelled porcelain tile. The raw materials of the standard mass components and the SBA residue were characterized by testing by XRF, XRD, AG, DTA and TGA. Test samples were fabricated, assembled in lots of 3 units and sintered at temperatures of 1150 ° C to 1210 ° C. The results of the physical properties, mechanical properties and SEM of the sintered samples, showed that the formulation, G4 - in which applied 10% of SBA replacing phyllite, sintering temperature 1210 ° C showed better performance as the previously mentioned properties due to the formation of mullite crystals, meeting the prerequisites of standards for enamelled porcelain tile, while reducing the environmental impact and the cost of production.

The current issues of using innovative solutions in waste-free management systems

2021 ◽  
pp. 136-148
Author(s):  
Olga Vytvytska ◽  
Mykyt Pundyk
Keyword(s):  
Raw Materials ◽  
Waste Recycling ◽  
Household Waste ◽  
Management Systems ◽  
Energy Technology ◽  
Processing Technologies ◽  
Management Technology ◽  
Innovative Solutions ◽  
The Cost ◽  
Theoretical Foundations

The purpose of the article. The purpose of the study is to substantiate the theoretical foundations and practical innovative solutions for the reuse of waste resources with a proposal for improved waste management technology with prospects for implementation in Ukraine. Research methodology: theoretical and practical aspects of the introduction and implementation of eco-management, because for Ukraine such an approach to the introduction of innovative processing technologies in enterprises is completely new. Methodical toolkit of substantiation of innovative decisions of reuse of resources from waste, structure of prime cost of the improved system for the Goloseevsky area. Kiev. Scientific novelty. It is proposed to optimize the existing garbage problem in most regions and replace waste trucks based on the method of the pneumatic system manufactured by Envac. The system allows you to reduce the cost of moving cargo over time sorting or disposal points. Conclusions. The introduction of innovative systems in Ukraine for the year saves UAH 34 billion 499 million, in addition, the sorting of household waste is gaining popularity, recycling tanks are being installed in cities, the population is beginning to treat waste with understanding, and a behavioral strategy has been introduced to stimulate waste recycling. In addition, the proposed technology of sorting raw materials allows you to sort up to 97% of household waste, and the rest to burn for energy. All this makes the development of the processing industry in Ukraine promising. Keywords: innovations, waste-free systems, secondary raw materials, energy, technology.

Sign in / Sign up

Export Citation Format

Share Document