High Temperature Corrosion Behaviors of Carbon Steels by A Pressurized Water

2007 ◽  
Vol 26-28 ◽  
pp. 1063-1066
Author(s):  
Sang Ll Lee ◽  
Moon Hee Lee ◽  
Jin Kyung Lee ◽  
Joon Hyun Lee ◽  
Yu Sik Kong
Keyword(s):  
High Temperature ◽  
Ultrasonic Wave ◽  
Corrosion Test ◽  
Water Pressure ◽  
Test Sample ◽  
Carbon Steels ◽  
Acoustic Emission Sensor ◽  
Pressurized Water ◽  
Corrosion Behaviors

The long-term corrosion resistances for the carbon steels have been investigated under high temperature pressurized water atmosphere, in the conjunction with the analysis of nondestructive properties by the ultrasonic wave. The corrosion test for carbon steels was carried out at the temperature of 200 °C under a water pressure of 10 MPa. The corrosion test cycles for carbon steels were changed up to 65 weeks. The mechanical properties of carbon steel suffered from the corrosion cycle were investigated by a tensile test, attaching an acoustic emission sensor on the test sample. The tensile strength of carbon steels greatly decreased beyond the corrosion cycle of 35 weeks, accompanying the increase of weight loss by the creation of corrosion damages. The attenuation coefficient of carbon steels by the ultrasonic wave increased with the increase of corrosion cycles.

Corrosion Resistance and Mechanical Properties of Carbon Steel under a High Temperature Pressurized Water

2007 ◽  
Vol 345-346 ◽  
pp. 1027-1030
Author(s):  
Sang Ll Lee ◽  
Moon Hee Lee ◽  
Jin Kyung Lee ◽  
Dong Su Bae ◽  
Joon Hyun Lee
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Carbon Steel ◽  
Corrosion Test ◽  
Water Pressure ◽  
Strength Properties ◽  
Carbon Steels ◽  
Pressurized Water ◽  
Corrosion Strength

The long-term corrosion strength properties for the carbon steels under pressurized water atmosphere have been investigated, in the conjunction with the detailed analysis of their microstructures. The corrosion test for carbon steels was carried out at the temperature of 200°C under a water pressure of 10 MPa. The corrosion test samples were maintained up to 50 weeks in the tube shaped reactor. The mechanical strength and the microstucture of carbon steels suffered from the long term corrosion test were evaluated by SEM, XRD and tensile test. The weight loss of carbon steel by the corrosion test was also examined. The tensile strength of carbon steels decreased with the increase of corrosion time under a pressurized water atmosphere, accompanying the creation of severe corrosion damages like stress corrosion crack.

Pressurized Water Corrosion Resistance of Carbon Steels and Their Nondestructive Characterization

2007 ◽  
Vol 353-358 ◽  
pp. 2407-2410
Author(s):  
Sang Ll Lee ◽  
Jin Kyung Lee ◽  
Tae Soo An ◽  
Joon Hyun Lee ◽  
Jun Young Park
Keyword(s):  
Tensile Strength ◽  
Corrosion Resistance ◽  
Carbon Steel ◽  
Test Specimen ◽  
Corrosion Test ◽  
Water Pressure ◽  
Carbon Steels ◽  
Pressurized Water ◽  
Damage Degree ◽  
Nondestructive Characterization

This study dealt with the corrosion resistance for the carbon steels under a pressurized water atmosphere at the elevated temperature. The nondestructive test was also used to evaluate the damage degree of corrosion test specimen. The corrosion test for carbon steels was carried out at the temperature of 200 °C under a water pressure of 10 MPa. The corrosion time for carbon steel was changed up to 20 weeks. The strength of carbon steel by the degree of corrosion was investigated by a tensile test. The carbon steel showed an average tensile strength of about 500 MPa after the corrosion period of 20 weeks, accompanying the weight loss of about 2.5 %. The attenuation coefficient of ultrasonic wave can be utilized as useful parameters to inspect the corrosion damages of carbon steels.

scholarly journals The Long-Term Corrosion Test Facility at Lawrence Livermore National Laboratory

2007 ◽  
Author(s):  
David V. Fix ◽  
Raul B. Rebak
Keyword(s):  
Corrosion Test ◽  
Lawrence Livermore National Laboratory ◽  
National Laboratory ◽  
Carbon Steels ◽  
Test Facility ◽  
Environmentally Assisted Cracking ◽  
Alloy 22 ◽  
Testing Susceptibility ◽  
Standard Weight

The long-term corrosion test facility (LTCTF) at the Lawrence Livermore National Laboratory (LLNL) consisted of 22 vessels that housed more than 7,000 corrosion test specimens from carbon steels to highly corrosion resistant materials such Alloy 22 and Ti Grade 7. The specimens from LTCTF range from standard weight-loss coupons to U-bend specimens for testing susceptibility to environmentally assisted cracking. Each vessel contained approximately 1000 liters of concentrated brines at 60°C or 90°C. The LTCTF started its operations in late 1996. Thousands of specimens were removed from the LTCTF in August-September 2006. The specimens are being catalogued and stored for future characterization. Previously removed specimens (e.g. 1 and 5 years) are also archived for further studies.

Microstructural characterization of a rapidly solidified Al-Fe-V-Si alloy for elevated temperature applications

1988 ◽  
Vol 46 ◽  
pp. 550-551
Author(s):  
R. E. Franck ◽  
J. A. Hawk ◽  
G. J. Shiflet
Keyword(s):  
High Temperature ◽  
Elevated Temperature ◽  
Grain Growth ◽  
Volume Fraction ◽  
Microstructural Characterization ◽  
Second Phase ◽  
Microstructural Stability ◽  
Elevated Temperature Strength ◽  
Temperature Applications

Rapid solidification processing (RSP) is one method of producing high strength aluminum alloys for elevated temperature applications. Allied-Signal, Inc. has produced an Al-12.4 Fe-1.2 V-2.3 Si (composition in wt pct) alloy which possesses good microstructural stability up to 425°C. This alloy contains a high volume fraction (37 v/o) of fine nearly spherical, α-Al12(Fe, V)3Si dispersoids. The improved elevated temperature strength and stability of this alloy is due to the slower dispersoid coarsening rate of the silicide particles. Additionally, the high v/o of second phase particles should inhibit recrystallization and grain growth, and thus reduce any loss in strength due to long term, high temperature annealing.The focus of this research is to investigate microstructural changes induced by long term, high temperature static annealing heat-treatments. Annealing treatments for up to 1000 hours were carried out on this alloy at 500°C, 550°C and 600°C. Particle coarsening and/or recrystallization and grain growth would be accelerated in these temperature regimes.

KUBOTA KNC-03

Alloy Digest ◽  
2010 ◽  
Vol 59 (1) ◽  
Keyword(s):  
Compressive Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
High Strength ◽  
Temperature Performance ◽  
Resistance To Oxidation

Abstract Kubota KNC-03 is a grade with a combination of high strength and excellent resistance to oxidation. These properties make this alloy suitable for long-term service at temperature up to 1250 deg C (2282 deg F). This datasheet provides information on physical properties, hardness, elasticity, tensile properties, and compressive strength as well as creep. It also includes information on high temperature performance as well as casting and joining. Filing Code: Ni-676. Producer or source: Kubota Metal Corporation, Fahramet Division. See also Alloy Digest Ni-662, April 2008.

ATI 6-2-4-2

Alloy Digest ◽  
2020 ◽  
Vol 69 (8) ◽  
Keyword(s):  
Tensile Strength ◽  
Titanium Alloy ◽  
High Temperature ◽  
Creep Strength ◽  
High Strength ◽  
Heat Treating ◽  
Good Combination ◽  
Long Term Stability ◽  
Temperature Performance

Abstract ATI 6-2-4-2 is a near-alpha, high strength, titanium alloy that exhibits a good combination of tensile strength, creep strength, toughness, and long-term stability at temperatures up to 425 °C (800 °F). Silicon up to 0.1% frequently is added to improve the creep resistance of the alloy. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as creep. It also includes information on high temperature performance as well as forming, heat treating, machining, and joining. Filing Code: Ti-169. Producer or Source: ATI.

S-TEN1

Alloy Digest ◽  
2005 ◽  
Vol 54 (8) ◽  
Keyword(s):  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Carbon Steels ◽  
Dew Point ◽  
Steel Alloy ◽  
Temperature Performance ◽  
Nippon Steel Corporation ◽  
Steel Corporation

Abstract S-TEN1 is a steel alloy containing copper and antimony to make it more resistant to dew-point corrosion than conventional carbon steels. It is used as tubing in economizers. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming and joining. Filing Code: SA-550. Producer or source: Nippon Steel USA Inc., Nippon Steel Corporation.

scholarly journals CO Detection Investigation at High Temperature by SiC MISFET Metal/Oxide Gas Sensors

Proceedings ◽  
2021 ◽  
Vol 56 (1) ◽  
pp. 41
Author(s):  
Lida Khajavizadeh ◽  
Anita Lloyd Spetz ◽  
Mike Andersson
Keyword(s):  
High Temperature ◽  
Gas Sensors ◽  
Elevated Temperatures ◽  
Long Term Stability ◽  
Stability Performance ◽  
Catalytic Metal ◽  
Co Detection ◽  
Effect Transistor ◽  
Metal Oxide Gas Sensors

In order to investigate the necessary device improvements for high-temperature CO sensing with SiC metal insulator semiconductor field effect transistor (MISFET)-based chemical gas sensors, devices employing, as the gas-sensitive gate contact, a film of co-deposited Pt/Al2O3 instead of the commonly used catalytic metal-based contacts were fabricated and characterized for CO detection at elevated temperatures and different CO and O2 levels. It can be concluded that the sensing mechanism at elevated temperatures correlates with oxygen removal from the sensor surface rather than the surface CO coverage as observed at lower temperatures. The long-term stability performance was also shown to be improved compared to that of previously studied devices.

Sign in / Sign up

Export Citation Format

Share Document