Multi-Criteria Optimization in End Milling of AISI D2 Hardened Steel Using Coated Carbide Inserts

2011 ◽  
Vol 264-265 ◽  
pp. 907-912
Author(s):  
A.N. Mustafizul Karim ◽  
Mohd Amri Lajis ◽  
A.K.M. Nurul Amin
Keyword(s):  
Surface Roughness ◽  
Tool Life ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Aisi D2 ◽  
Machining Operations ◽  
Coated Carbide ◽  
Desirability Index

This paper proposes a multi-criteria optimization technique using the mathematical models developed by the response surface methodology (RSM) for the target responses combined with desirability indices for the determining the optimum cutting parameters in end milling of AISI D2 hardened steels. Different responses may require different targets either being maximized or minimized. Simultaneous achievement of the optimized (maximum or minimum) values of all the responses is very unlikely. In machining operations tool life and volume metal removed are targeted to be maximized whereas the machined surface roughness need to be at minimum level. Models showing the combined effect of the three control factors such as cutting speed, feed, and depth of cut are developed. However, a particular combination of parameter levels appears to be optimum for a particular response but not for all. Thus adoption of the method of consecutive searches with higher desirability values is found to be appropriate. In this study the desirability index reaches to a maximum value of 0.889 after five consecutive solution searching. At this stage, the optimum values of machining parameters - cutting speed, depth of cut and feed were determined as 44.27 m/min, 0.61 mm, 0.065 mm/tooth respectively. Under this set condition of machining operations a surface roughness of 0.348 μm and volume material removal of 7.45 cm3 were the best results compared to the rest four set conditions. However, the tool life would be required to compromise slightly from the optimum value.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

Preheating in End Milling of AISI D2 Hardened Steel with Coated Carbide Inserts

2009 ◽  
Vol 83-86 ◽  
pp. 56-66 ◽  
Author(s):  
Mohd Amri Lajis ◽  
A.K.M. Nurul Amin ◽  
A.N. Mustafizul Karim ◽  
A.M.K. Hafiz
Keyword(s):  
Tool Wear ◽  
Surface Finish ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Inductive Heating ◽  
Machining Parameters ◽  
Aisi D2 ◽  
Coated Carbide

This study was conducted to investigate the effect of preheating through inductive heating mechanism in end milling of AISI D2 hardened steel (60-62 HRC) by using coated carbide tool inserts. Apart from preheating, two other machining parameters such as cutting speed and feed were varied while the depth of cut constant was kept constant. Tool wear phenomenon and machined surface finish were found to be significantly affected by preheating temperature and other two variables. End milling operation was performed on a Vertical Machining Centre (VMC). Preheating of the work material to a higher temperature range resulted in a noticeable reduction in tool wear rate leading to a longer tool life. In addition, improved surface finish was obtained with surface roughness values lower than 0.4 μm, leaving a possibility of skipping the grinding and polishing operations for certain applications.

Effect of machining parameters on the surface finish of a metal matrix composite under dry cutting conditions

2015 ◽  
Vol 231 (6) ◽  
pp. 913-923 ◽  
Author(s):  
Brian Boswell ◽  
Mohammad Nazrul Islam ◽  
Ian J Davies ◽  
Alokesh Pramanik
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Tool Life ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Dry Cutting

The machining of aerospace materials, such as metal matrix composites, introduces an additional challenge compared with traditional machining operations because of the presence of a reinforcement phase (e.g. ceramic particles or whiskers). This reinforcement phase decreases the thermal conductivity of the workpiece, thus, increasing the tool interface temperature and, consequently, reducing the tool life. Determining the optimum machining parameters is vital to maximising tool life and producing parts with the desired quality. By measuring the surface finish, the authors investigated the influence that the three major cutting parameters (cutting speed (50–150 m/min), feed rate (0.10–0.30 mm/rev) and depth of cut (1.0–2.0 mm)) have on tool life. End milling of a boron carbide particle-reinforced aluminium alloy was conducted under dry cutting conditions. The main result showed that contrary to the expectations for traditional machined alloys, the surface finish of the metal matrix composite examined in this work generally improved with increasing feed rate. The resulting surface roughness (arithmetic average) varied between 1.15 and 5.64 μm, with the minimum surface roughness achieved with the machining conditions of a cutting speed of 100 m/min, feed rate of 0.30 mm/rev and depth of cut of 1.0 mm. Another important result was the presence of surface microcracks in all specimens examined by electron microscopy irrespective of the machining condition or surface roughness.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

Modeling & Optimization of Surface Roughness & Vibration Amplitude in Heat Assisted End Milling of SKD 11 Tool Steel Using Ball Nose Tool

2012 ◽  
Vol 538-541 ◽  
pp. 799-803 ◽  
Author(s):  
A.K.M. Nurul Amin ◽  
Muhd Hafiz B. Md. Saad ◽  
Muammer Din Arif
Keyword(s):  
Surface Roughness ◽  
Response Surface ◽  
Tool Steel ◽  
Vibration Amplitude ◽  
End Milling ◽  
Heating Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Primary Input ◽  
Coated Carbide

Tool steel - SKD 11 is frequently used in industries for making dies and molds. This grade is chosen for its toughness, strength, and hardness maintained up to high temperature. However, the same properties make the steel extremely difficult and expensive to machine using conventional approaches. Heat assisted machining has been found wide spread application in recent years to improve machinability of difficult-to-cut materials. This research paper presents the outcome of an investigation on heat assisted end milling of SKD 11 conducted on a vertical machining center using ball nose coated carbide inserts. The Design of Experiments (DoE) was done using the Response Surface Methodology, in order to develop empirical mathematical models of surface roughness and vibration in terms of cutting speed, feed, axial depth of cut, and heating temperature. The models were checked for significance using Analysis of Variance (ANOVA). 3-D response surface graphs of the interactions of primary cutting parameters with the responses were plotted. Optimization was then performed by using the desirability function approach. From the graphs and optimized results it was concluded that the primary input parameters could be controlled in order to reduce vibration amplitude and produce semi-finished machined surfaces applying induction heat assisted technique.

Machining parameters effect in dry turning of AISI 316L stainless steel using coated carbide tools

2015 ◽  
Vol 231 (4) ◽  
pp. 676-683 ◽  
Author(s):  
Rusdi Nur ◽  
MY Noordin ◽  
S Izman ◽  
D Kurniawan
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Power Consumption ◽  
Cutting Force ◽  
Tool Life ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
Machining Parameters ◽  
Aisi 316L ◽  
Coated Carbide

Austenitic stainless steel AISI 316L is used in many applications, including chemical industry, nuclear power plants, and medical devices, because of its high mechanical properties and corrosion resistance. Machinability study on the stainless steel is of interest. Toward sustainable manufacturing, this study also includes the power consumption during machining along with other machining responses of cutting force, surface roughness, and tool life. Turning on the stainless steel was performed using coated carbide tool without using cutting fluid. The turning was performed at various cutting speeds (90, 150, and 210 m/min) and feeds (0.10, 0.16, and 0.22 mm/rev). Response surface methodology was adopted in designing the experiments to quantify the effect of cutting speed and feed on the machining responses. It was found that cutting speed was proportional to power consumption and was inversely proportional to tool life, and showed no significant effect on the cutting force and the surface roughness. Feed was proportional to cutting force, power consumption, and surface roughness and was inversely proportional to tool life. Empirical equations developed from the results for all machining responses were shown to be useful in determining the optimum cutting parameters range.

scholarly journals Optimization of Atomized Spray Cutting Fluid Eco-Friendly Turning of Inconel 718 Alloy Using ARAS and CODAS Methods

2021 ◽  
Author(s):  
Vinothkumar Sivalingam ◽  
Ganeshkumar Poogavanam ◽  
Yuvaraj Natarajan ◽  
Jie Sun
Keyword(s):  
Surface Roughness ◽  
Power Consumption ◽  
Tool Life ◽  
Inconel 718 ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Parameter Setting ◽  
Inconel 718 Alloy ◽  
Desirability Index

Abstract Atomized spray cutting fluid (ASCF) is a sophisticated machining technique that achieves higher productivity, enhanced surface quality, extended tool life, and cost benefits. This research aims to analyze the influence of cutting process parameters on Inconel 718 alloy turning in dry and ASCF cutting environments. The critical machining indices such as surface roughness, machining cost, power consumption, and tool life were analyzed concerning these two cooling environments. The cutting parameters were optimized using desirability functional analysis and two types of multicriteria decision making (MCDM) method, such as additive ratio assessment method (ARAS) and combinative distance-based assessment (CODAS) method, were investigated. The composite desirability index (CD) of optimum parameter setting(A2B1C2D2) is improved by 6.34 % compared to the initial parameter setting (A2B1C2D1). The optimum parameters from the MCDM technique are obtained as a cutting speed of 200 m/min, feed rate of 0.08 mm/rev, and depth of cut of 0.2 mm under ASCF environment. ASCF machining significantly minimize the surface roughness, machining cost and power consumption, maximize the tool life by about 16%, 51%, 17% and 48% respectively as compared with dry machining

Machinability Investigation of HSLA Steel in Hard Turning with Coated Ceramic Tool: Assessment, Modeling, Optimization and Economic Aspects

2019 ◽  
Vol 18 (04) ◽  
pp. 625-655 ◽  
Author(s):  
Asutosh Panda ◽  
Sudhansu Ranjan Das ◽  
Debabrata Dhupal
Keyword(s):  
Surface Roughness ◽  
Tool Life ◽  
Hard Turning ◽  
Flank Wear ◽  
Desirability Function ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Ceramic Tool ◽  
Life Estimation

The present study addresses the machinability investigation in finish dry hard turning of high strength low alloy steel with coated ceramic tool by considering cutting speed, feed and depth of cut as machining parameters. The technological parameters like surface roughness, flank wear, chip morphology and economical feasibility have been considered to investigate the machinability performances. Twenty seven set of trials according to full factorial design of experiments are performed and analysis of variance, multiple regression method, Taguchi method, desirability function approach and finally Gilbert’s approach are subsequently applied for parametric influence study, mathematical modeling, multi-response optimization, tool life estimation and economic analysis. Results indicated that feed and cutting speed are the most significant controlled as well as dominant factors for hard turning operation if the minimization of the machined surface roughness and tool flank wear is considered. Abrasions, adhesion followed by plastic deformation have been observed to be the principal wear mechanism for tool life estimation and observed tool life for coated ceramic insert is 47[Formula: see text]min under optimum cutting conditions. The total machining cost per part is ensued to be lower ($0.29 only) as a consequence of higher tool life, reduction in downtime and enhancement in savings, which finds economical benefits in hard turning. The current work demonstrates the substitution of conventional, expensive and slow cylindrical grinding process, and proposes the most expensive CBN tool alternative using coated ceramic tools in hard turning process considering techno-economical and ecological aspects.

Surface Roughness Prediction in End Milling of Machinable Glass Ceramic and Optimization by Response Surface Methodology

2011 ◽  
Vol 189-193 ◽  
pp. 1376-1381
Author(s):  
Moola Mohan Reddy ◽  
Alexander Gorin ◽  
Khaled A. Abou El Hossein
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Glass Ceramic ◽  
End Milling ◽  
Removal Rate ◽  
Cutting Speed ◽  
Lower Surface ◽  
Depth Of Cut ◽  
Machining Parameters

This paper presents the prediction of a statistically analyzed model for the surface roughness,R_a of end-milled Machinable glass ceramic (MGC). Response Surface Methodology (RSM) is used to construct the models based on 3-factorial Box-Behnken Design (BBD). It is found that cutting speed is the most significant factor contributing to the surface roughness value followed by the depth of cut and feed rate. The surface roughness value decreases for higher cutting speed along with lower feed and depth of cut. Additionally, the process optimization has also been done in terms of material removal rate (MRR) to the model’s response. Ideal combinations of machining parameters are then suggested for common goal to achieve lower surface roughness value and higher MRR.

Surface Roughness Optimization in End Milling Using the Multi Objective Genetic Algorithm Approach

2012 ◽  
Vol 576 ◽  
pp. 103-106 ◽  
Author(s):  
Muataz H.F. Al Hazza ◽  
Erry Yulian Triblas Adesta ◽  
Muhammad Riza ◽  
M.Y. Suprianto
Keyword(s):  
Genetic Algorithm ◽  
Surface Roughness ◽  
End Milling ◽  
Cutting Speed ◽  
Root Mean Square Roughness ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Multi Objective ◽  
Multi Objective Genetic Algorithm ◽  
Machining Optimization

In finishing end milling, not only good accuracy but also good roughness levels must be achieved. Therefore, determining the optimum cutting levels to achieve the minimum surface roughness is important for it is economical and mechanical issues. This paper presents the optimization of machining parameters in end milling processes by integrating the genetic algorithm (GA) with the statistical approach. Two objectives have been considered, minimum arithmetic mean roughness (Ra) and minimum Root-mean-square roughness (Rq). The mathematical models for the surface roughness parameters have been developed, in terms of cutting speed, feed rate, and axial depth of cut by using Response Methodology Method (RSM). Due to complexity of this machining optimization problem, a multi objective genetic algorithm (MOGA) has been applied to resolve the problem, and the results have been analyzed.

Sign in / Sign up

Export Citation Format

Share Document