Numerical Simulation on Vibration-Assisted Ultra-Precision Cutting of Steel AISI 1045 with PCD Tool

2012 ◽  
Vol 497 ◽  
pp. 324-328 ◽  
Author(s):  
Ahmed Al-Zahrani ◽  
Xiao Dan Xie ◽  
Yong Li
Keyword(s):  
Cutting Force ◽  
Polycrystalline Diamond ◽  
Finite Element Software ◽  
Pcd Tool ◽  
Optimum Selection ◽  
Aisi 1045 ◽  
Ultra Precision ◽  
Steel Aisi ◽  
Different Depths ◽  
Tool Cutting

Vibration-assisted cutting (VAC) with polycrystalline diamond (PCD) tool refers to the cutting with certain amplitude and high frequency tool vibration, which can definitely reduce the cutting force and tool wear compared with conventional cutting (CC). In this paper, a plane strain orthogonal model for PCD tool cutting steel AISI 1045 is established by using the finite element software ABAQUS/explicit. Then the cutting force of VAC compared with CC is explained. The value and distribution of cutting force at different depths of cutting is analyzed. It is also studied the effects of vibration frequency and amplitude on cutting force and thrust force during the ultra-precision cutting process. Afterwards, optimum selection of process parameters is presented for VAC processing of steel AISI 1045.

scholarly journals Study of cutting force and tool wear during turning of aluminium with WC, PCD and HFCVD coated MCD tools

2020 ◽  
Vol 7 ◽  
pp. 27
Author(s):  
Sisira Kanta Pattnaik ◽  
Minaketan Behera ◽  
Sachidananda Padhi ◽  
Pusparaj Dash ◽  
Saroj Kumar Sarangi
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Cutting Force ◽  
Cutting Tools ◽  
Chemical Vapor ◽  
Polycrystalline Diamond ◽  
Machining Process ◽  
Pcd Tool ◽  
Rolled Aluminum ◽  
Pcd Tools

Enormous developmental work has been made in synthesis of metastable diamond by hot filament chemical vapor deposition (HFCVD) method. In this paper, micro-crystalline diamond (MCD) was deposited on WC–6 wt.% Co cutting tool inserts by HFCVD technique. The MCD coated tool was characterized by the scanning electron microscope (SEM), X-ray diffraction (XRD) and micro Raman spectroscopy (μ-RS). A comparison was made among the MCD tool, uncoated tungsten carbide (WC) tool and polycrystalline diamond (PCD) tool during the dry turning of rolled aluminum. The various major tests were conducted such as surface roughness, cutting force and tool wear, which were taken into consideration to establish a proper comparison among the advanced cutting tools. Surface roughness was measured during machining by Talysurf. The tool wear was studied by SEM after machining. The cutting forces were measured by Kistler 3D-dynamometer during the machining process. The test results indicate that, the CVD coated MCD tool and PCD tool produced almost similar results. But, the price of PCD tools are five times costlier than MCD tools. So, MCD tool would be a better alternative for machining of aluminium.

Finite Element Simulation of PCD Tool Cutting Titanium Alloy

2013 ◽  
Vol 589-590 ◽  
pp. 64-69
Author(s):  
Xian Li Liu ◽  
Jia Yi Zhang ◽  
Yu Wang ◽  
Cai Xu Yue ◽  
Fei Liu
Keyword(s):  
Titanium Alloy ◽  
Cutting Force ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Pcd Tool ◽  
Element Simulation ◽  
Force Increase ◽  
Tool Cutting ◽  
Deform 3D

Titanium alloy is widely applied in various fields, but it’s a sort of difficult-to-cut material. In this paper, DEFORM-3D is used to carry on a simulation of PCD tool milling Ti6A14V. Variation curves of cutting temperature and cutting force are obtained by changing cutting speed, feed per tooth and axial cutting depth. Further, the effect of cutting parameters on cutting temperature and cutting force is revealed. The research shows that cutting temperature and cutting force increase with cutting parameters. In addition, single factor experiments are conducted to verify that the results of the experiments are in consistent with those of the simulation, and that the simulation model is correct. The results will provide new methods for studies of cutting temperature and cutting force of PCD tool milling Ti6A14V.

Study on Additional Electrical Current on Machinability of Free-Machining Steels in Turning

2010 ◽  
Vol 34-35 ◽  
pp. 1775-1779
Author(s):  
Yong Chuan Lin ◽  
Yuan Ling Chen
Keyword(s):  
Cutting Force ◽  
Current Source ◽  
Cutting Speed ◽  
Electrical Current ◽  
Carbide Tool ◽  
Cutting Mechanism ◽  
High Cutting Speed ◽  
Aisi 1045 ◽  
Steel Aisi ◽  
Standard Steel

This paper deals with the mach inability of BN free-machining steel in turning with a supplied current of various values and different directions of electrical current. The tested work pieces were, standard steel AISI 1045 and BN added steel (AISI 1045-BN) based AISI 1045 which has good mach inability at high cutting speed. Turning tests were performed by carbide tool P30 and the power source for additional electrical current supply was a direct current source and the maximum electrical current in the circuit was 20milliamperes (mA). To investigate the influence of electrical conditions of closed circuit system on the cutting mechanism of AISI 1045-BN. The tool life, cutting force, and others were determined experimentally. The testing results show that when turning with carbide tool P30 the maximum crater depth in the tool was reduced drastically when the value of supplied current reached 5mA, regardless of its direction of flow, compared with depths at lower current values; the additional electrical current cutting showed smaller cutting force than those of conditions when turning AISI 1045-BN.

scholarly journals Correction and accuracy improvement of non-parallel shear zone model

2018 ◽  
Vol 207 ◽  
pp. 02002
Author(s):  
Yaoke Wang ◽  
Meng Kou ◽  
Wei Ding ◽  
Huan Ma ◽  
Liangshan Xiong
Keyword(s):  
Experimental Data ◽  
Cutting Force ◽  
Shear Zone ◽  
Coordinate Transformation ◽  
Chip Thickness ◽  
Zone Model ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
Experimental Values ◽  
1045 Steel

When applying the non-parallel shear zone model to predict the cutting process parameters of carbon steel workpiece, it is found that there is a big error between the prediction results and the experimental values. And also, the former approach to obtain the relevant cutting parameters of the non-parallel shear zone model by applying coordinate transformation to the parallel shear zone model has a theoretical error – it erroneously regards the determinant (|J|) of the Jacobian matrix (J) in the coordinate transformation as a constant. The shape of the shear zone obtained when |J| is not constant is drew and it is found that the two boundaries of the shear zone are two slightly curved surfaces rather than two inclined planes. Also, the error between predicted values and experimental values of cutting force and cutting thrust is slightly smaller than that of constant |J|. A corrected model where |J| is a variable is proposed. Since the specific values of inclination of the shear zone (α, β), the thickness coefficient of the shear zone (as) and the constants related to the material (f0, p) are not given in the former work, a method to obtain the above-mentioned five constants by solving multivariable constrained optimization problem based on experimental data was also proposed; based on the obtained experimental data of AISI 1045 steel workpiece cutting force, cutting thrust, chip thickness, the results of five above-mentioned model constants are obtained. It is found that, compared with prediction from uncorrected model, the cutting force and cutting thrust of AISI 1045 steel predicted by the corrected model with the obtained constants has a better agreement with the experimental values obtained by Ivester.

scholarly journals Micrometer-scale machining of metals and polymers enabled by focused ion beam sputtering

1998 ◽  
Vol 546 ◽  
Author(s):  
D. P. Adams ◽  
G. L. Benavides ◽  
M. J. vasile
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Ion Beam Sputtering ◽  
Beam Sputtering ◽  
End Mills ◽  
Ultra Precision ◽  
Tool Shank ◽  
Micrometer Scale ◽  
Tool Cutting ◽  
Micro Tools

AbstractThis work combines focused ion beam sputtering and ultra-precision machining for microfabrication of metal alloys and polymers. Specifically, micro-end mills are made by Ga ion beam sputtering of a cylindrical tool shank. Using an ion energy of 20keV, the focused beam defines the tool cutting edges that have submicrometer radii of curvature. We demonstrate 25μm diameter micromilling tools having 2, 4 and 5 cutting edges. These tools fabricate fine channels, 26–28 microns wide, in 6061 aluminum, brass, and polymethyl methacrylate. Micro-tools are structurally robust and operate for more than 5 hours without fracture.

A Metallo-Thermomechanically Coupled Analysis of Orthogonal Cutting of AISI 1045 Steel

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Hongtao Ding ◽  
Yung C. Shin
Keyword(s):  
Experimental Data ◽  
Cutting Force ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Chip Morphology ◽  
Machining Process ◽  
Coupled Analysis ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel

Materials often behave in a complicated manner involving deeply coupled effects among stress/stain, temperature, and microstructure during a machining process. This paper is concerned with prediction of the phase change effect on orthogonal cutting of American Iron and Steel Institute (AISI) 1045 steel based on a true metallo-thermomechanical coupled analysis. A metallo-thermomechanical coupled material model is developed and a finite element model (FEM) is used to solve the evolution of phase constituents, cutting temperature, chip morphology, and cutting force simultaneously using abaqus. The model validity is assessed using the experimental data for orthogonal cutting of AISI 1045 steel under various conditions, with cutting speeds ranging from 198 to 879 m/min, feeds from 0.1 to 0.3 mm, and tool rake angles from −7 deg to 5 deg. A good agreement is achieved in chip formation, cutting force, and cutting temperature between the model predictions and the experimental data.

scholarly journals Analisis Perancangan Frame Gokart dari Pengaruh Pembebanan dengan Menggunakan CAD Solidworks 2016

Jurnal METTEK ◽  
2021 ◽  
Vol 7 (1) ◽  
pp. 1
Author(s):  
Angga Restu Pahlawan ◽  
Rizal Hanifi ◽  
Aa Santosa
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Safety Factor ◽  
Frame Structure ◽  
Maximum Displacement ◽  
Element Analysis ◽  
Aisi 1045 ◽  
Steel Aisi ◽  
Simulation Results ◽  
Manual Calculation

Frame adalah salah satu komponen yang sangat penting dalam sebuah kendaraan, yang berfungsi sebagai penopang penumpang, mesin, suspensi, sistem kelistrikan dan lain-lain. Melihat fungsi dari frame sangat penting, maka dalam merancang sebuah frame harus diperhitungkan dengan baik. Banyak sekali jenis pengujian yang sering dipakai dalam perancangan sebuah struktur frame, salah satunya adalah digunakannya metode komputasi dengan menggunakan metode Finite Element Analysis (FEA). Tujuan dari penelitian ini adalah untuk mengetahui distribusi tegangan, regangan, displacement, dan safety factor dari hasil pembebanan statis pada frame gokar. Struktur frame didesain dan dianalisis menggunakan software Solidworks 2016. Material yang digunakan frame adalah baja AISI 1045 hollow tube 273,2 mm, dengan menggunakan pembebanan pengendara sebesar 50 kg dan 70 kg. Hasil dari perhitungan manual didapatkan tegangan maksimum sebesar 4,735  107 N/m2, sedangkan dari simulasi didapatkan sebesar 4,516  107 N/m2. Regangan maksimum didapatkan dari perhitungan manual sebesar 2,310  10-4. Displacement maksimum didapatkan dari perhitungan manual sebesar 1,864  108 mm, sedangkan dari simulasi didapatkan sebesar 1,624  108 mm. Safety factor minimum didapatkan dari perhitungan manual sebesar 11,193, dan perhitungan simulasi didapatkan sebesar 11,736. The frame is one of the most important components in a vehicle, which functions as a support for passengers, engines, suspensions, electrical systems and others. Seeing the function of the frame is very important, so designing a frame must be taken into account well. There are many types of tests that are often used in the design of a frame structure, one of which is the use of computational methods using the Finite Element Analysis (FEA) method. The purpose of this study was to determine the distribution of stress, strain, displacement, and safety factor from the results of static loading on the kart frame. The frame structure was designed and analyzed using Solidworks 2016 software. The material used in the frame is steel AISI 1045 hollow tube 27  3,2 mm, using a rider load of 50 kg and 70 kg. The result of manual calculation shows that the maximum stress is 4,735  107 N/m2, while the simulation results are 4,516  107 N/m2. The maximum strain is obtained from manual calculation of 2,310  10-4. The maximum displacement is obtained from manual calculations of 1,864  108 mm, while the simulation results are 1,624  108 mm. The minimum safety factor obtained from manual calculation is 11,193, and the simulation calculation is 11,736.

Analysis of characteristics of arc shape caused by intermittent cutting force and dynamic vibration in ultra-precision cutting processes

2020 ◽  
Vol 234 (14) ◽  
pp. 1742-1751
Author(s):  
Wei Wei ◽  
Jiasheng Li ◽  
Yi Chen ◽  
Xiaojin Huang
Keyword(s):  
Cutting Force ◽  
Surface Characteristics ◽  
Spindle Speed ◽  
Feed Speed ◽  
Dynamic Vibration ◽  
Tool Shape ◽  
Arc Shape ◽  
Ultra Precision ◽  
Cutting Processes ◽  
Intermittent Cutting

This article analyzes the phenomenon of “arc shape” in surface characteristics caused by dynamic vibration in ultra-precision machining. First, a surface simulation model is proposed based on the effect of the tool shape on the cutting profile. The accurate mapping relationship between spindle speed, feed speed, relative vibration, and the motion track of the tool tip to the workpiece profile is also established. Thereafter, the input frequency spectrum signature of an intermittent cutting force is found to be determined by the spindle speed and workpiece characteristics, and this is verified by experimental results. A phased, self-regulated mode of forced vibration caused by intermittent cutting force is then proposed, and the forming of the arc shape feature is explained. In addition, it is revealed that output vibration can be kept at a low level by adjusting the spectrum curve of the input signal.

Effect of Cutting Speed on the Face Milling of CFRP Using a PCD Tool

2016 ◽  
Vol 874 ◽  
pp. 487-491
Author(s):  
Takayuki Kitajima ◽  
Takumi Horiuchi ◽  
Akinori Yui ◽  
Yosuke Ito
Keyword(s):  
Mechanical Characteristics ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Polycrystalline Diamond ◽  
Face Milling ◽  
Fiber Reinforced Plastic ◽  
Pcd Tool ◽  
Reinforced Plastic ◽  
The Face ◽  
Cutting Speeds

Carbon-fiber-reinforced plastic (CFRP) is used in various industries such as aerospace and automobile industries because of its high mechanical characteristics. However, this material is difficult to cut. Tool wear and delamination frequently occur during the drilling or cutting of CFRP. In previous studies, we developed a CFRP cutting tool using polycrystalline diamond (PCD). The PCD tool exhibited excellent cutting performance at cutting speeds as low as <120 m/min. In this study, the authors investigated the effect of cutting speed on the face milling of CFRP by using the developed PCD tool.

Sign in / Sign up

Export Citation Format

Share Document