Study on the Truss Support Technology for Coal Side in a Soft Broken Coal Roadway Under High Stress

2012 ◽  
Vol 524-527 ◽  
pp. 360-363
Author(s):  
Shou Yi Dong ◽  
Qi Tao Duan ◽  
Fu Lian He ◽  
Qi Li ◽  
Hong Jun Jiang
Keyword(s):  
Production Condition ◽  
High Stress ◽  
Field Investigation ◽  
Surrounding Rock ◽  
Theory Analysis ◽  
Large Section ◽  
Cable Channel ◽  
Coal Roadway ◽  
Measurement Results ◽  
Steel Truss

The coal side deformation and sliding can not be effectively controlled by use of the traditional bolt or cable support in the high stress crushed surrounding rock and large section roadway. For solving this problem, the new prestressed truss support technology is put forward, and its supporting principles of roof and two walls are stated. The mechanical model of cable-channel steel truss is established, and then the tensile strength of the cable and the maximum deflection of the channel steel are derived. By way of field investigation, mechanics theory analysis and actual production condition, the scheme is defined and applied in the replacement roadway. Measurement results of surrounding rock behavior show that the coal side displacement is no more than 254mm and the roof convergence is less than 172mm. Apparent economic and technical profits have been achieved.

scholarly journals Study on Safety Control of Large-Section Roadway with High Stress and Broken Surrounding Rock

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Wen-qing Peng ◽  
Hao Zhu ◽  
Qi Wang ◽  
Gang Peng
Keyword(s):  
High Stress ◽  
Field Investigation ◽  
Surrounding Rock ◽  
Jiangxi Province ◽  
Engineering Practice ◽  
Large Section ◽  
Middle Point ◽  
Safety Control ◽  
Anchor Cable ◽  
The Stability

In order to solve the problem of difficult support of the roadway with high stress and large-section broken surrounding rock, this paper takes the subinclined shaft in Gaokeng mine of Jiangxi Province as the engineering background, analyzes the deformation mechanism and support mode of the roadway under the influence of mining through field investigation and mechanical derivation, and concludes that the stress concentration point of the roadway is in the middle point of roof and floor and the middle point of left and right sides. Through the modeling analysis of FLAC3D numerical software and the comparison of various support schemes, it is concluded that, after the combined support method of “anchor, net, and spray + grouting + full-section anchor cable + floor anchor cable“ is adopted, the convergence of roof and floor is reduced by 508 mm, and the convergence of two sides is reduced by 663 mm. And, it is applied in engineering practice. The results show that the combined support scheme can effectively control the stability of the surrounding rock.

scholarly journals Stability Control of Deep Coal Roadway under the Pressure Relief Effect of Adjacent Roadway with Large Deformation: A Case Study

2021 ◽  
Vol 13 (8) ◽  
pp. 4412
Author(s):  
Houqiang Yang ◽  
Nong Zhang ◽  
Changliang Han ◽  
Changlun Sun ◽  
Guanghui Song ◽  
...  
Keyword(s):  
Large Deformation ◽  
Coal Mine ◽  
High Stress ◽  
Surrounding Rock ◽  
Western China ◽  
Engineering Practice ◽  
Pressure Relief ◽  
Coal Roadway ◽  
And Control ◽  
Relief Effect

High-efficiency maintenance and control of the deep coal roadway surrounding rock stability is a reliable guarantee for sustainable development of a coal mine. However, it is difficult to control the stability of a roadway that locates near a roadway with large deformation. With return air roadway 21201 (RAR 21201) in Hulusu coal mine as the research background, in situ investigation, theoretical analysis, numerical simulation, and engineering practice were carried out to study pressure relief effect on the surrounding rock after the severe deformation of the roadway. Besides, the feasibility of excavating a new roadway near this damaged one by means of pressure relief effect is also discussed. Results showed that after the strong mining roadway suffered huge loose deformation, the space inside shrank so violently that surrounding rock released high stress to a large extent, which formed certain pressure relief effect on the rock. Through excavating a new roadway near this deformed one, the new roadway could obtain a relative low stress environment with the help of the pressure relief effect, which is beneficial for maintenance and control of itself. Equal row spacing double-bearing ring support technology is proposed and carried out. Engineering practice indicates that the new excavated roadway escaped from possible separation fracture in the roof anchoring range, and the surrounding rock deformation of the new roadway is well controlled, which verifies the pressure relief effect mentioned. This paper provides a reference for scientific mining under the condition of deep buried and high stress mining in western China.

scholarly journals Research on Control Mechanism of Surrounding Rock of Deep Gob-Side Entry Retaining

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Jianxiong Liu ◽  
Jingke Wu ◽  
Yun Dong ◽  
Yanyan Gao ◽  
Jihua Zhang ◽  
...  
Keyword(s):  
Large Deformation ◽  
High Stress ◽  
Original System ◽  
Field Investigation ◽  
Surrounding Rock ◽  
Eccentric Load ◽  
Deformation And Failure ◽  
Body Fracture ◽  
Stress States ◽  
Term Creep

To address the large deformation of the surrounding rock of deep gob-side entry retaining under high stress, lithological characteristics of the surrounding rock and failure model of support body and their evolutionary processes are analyzed through field investigation and theoretical analysis. Failure mechanisms of surrounding rock and the technology to control it are studied systematically. The results show that the causes of the large deformation of the surrounding rock are weak thick mudstones with softening property and water absorption behavior, as well as its fragmentation, dilatancy, and long-term creep during strong disturbance and highly centralized stress states. The cross-section shape of the roadway after deformation and failure of the surrounding rock is obviously asymmetric in both the horizontal and vertical directions. Since the original system supporting the surrounding rock is unable to completely bear the load, each part of the supporting system is destroyed one after the other. The failure sequences of the surrounding rock are as follows: (1) roadway roof fracture in the filling area, (2) filling body fracture under eccentric load, (3) rapid subsidence of the roadway roof, and (4) external crack drum and rib spalling at the solid coal side. Due to this failure sequence, the entire surrounding rock becomes unstable. A partitioned coupling support and a quaternity control technology to support the surrounding rock are proposed, in which the roof of the filling area plays a key role. The technology can improve the overall stability of gob-side entry retaining, prevent support structure instability caused by local failure of the surrounding rock, and ensure the safety and smoothness of roadways.

Design and Application of Secondary High-Capacity Support to Large-Section Tunnel Excavated in High-Stress Condition with Fractured Surrounding Rock

2012 ◽  
Vol 170-173 ◽  
pp. 1777-1784
Author(s):  
Xin Ming Chen
Keyword(s):  
Bearing Capacity ◽  
Stress Condition ◽  
Lateral Pressure ◽  
High Stress ◽  
High Capacity ◽  
Field Testing ◽  
Surrounding Rock ◽  
Large Section ◽  
Different Characteristics ◽  
High Stress Condition

Aimed at the support problem of the deep large-section tunnel excavated in high-stress condition with fractured surrounding rock, the different characteristics of the stresses and displacements of the surrounding rock of the tunnel with different section supports and lateral pressure coefficients were analyzed using numerical simulation and theoretical calculation, so was the effect of the height of the double-layered I-section beam on the bearing capacity. Arched with bottom arch superimposed and fully-closed I-section beam suitable for large-section tunnel excavated in high-stress condition with fractured surrounding rock was developed. This support applies fully-closed and horse-shoe shaped structure with I-section beam overlapped and welded and its bearing capacity is 2.5 times higher than frequently-used I-section beam. Underground field testing showed that the deformation of the surrounding rock could be effectively controlled when the secondary arched with bottom arch superimposed and fully-closed I-section beam of high bearing capacity was used.

scholarly journals Study on support optimization of coal roadway with soft and broken surrounding rock

2020 ◽  
Vol 165 ◽  
pp. 03037
Author(s):  
Li Li
Keyword(s):  
Field Investigation ◽  
Surrounding Rock ◽  
Mine Pressure ◽  
Deformation And Failure ◽  
Mining Depth ◽  
Coal Roadway ◽  
Geological Conditions ◽  
Support Optimization ◽  
Optimization Schemes

With the increase of mining depth, the geological conditions tend to be complex. The problems of high mine pressure and soft and broken surrounding rock are more serious, and the difficulty of support is significantly increased. In this paper, the coal roadway with soft and broken surrounding rock in Shuangliu coal mine was taken as the research object, the model was established by FLAC3D software, the deformation and failure characteristics of the surrounding rock of the roadway were studied, the distribution of the stress and plastic area of the roadway were analyzed, and the problems of the original support scheme were analyzed. Combined with the field investigation and analysis, a variety of optimization schemes were proposed, and the optimal support scheme was obtained through modelling and calculation. The results show that the sidewall and corner of coal roadway are the key parts of support, and strengthening its support strength is conducive to improving the overall stability of the roadway. W-type steel band can be used to connect the rock bolt and anchor cable together to play the role of coupling support, so as to achieve the overall support effect.

scholarly journals Combined Support Technology of Large Section Roadway in High-stress Fractured Surrounding Rock

2011 ◽  
Vol 26 ◽  
pp. 1270-1278 ◽  
Author(s):  
Zhan Ping ◽  
Ma Nianjie ◽  
Jiang Wei ◽  
Ren Jianju
Keyword(s):  
High Stress ◽  
Surrounding Rock ◽  
Large Section

scholarly journals Study on instability failure mode and monitoring early warning standard of surrounding rock in fully weathered argillaceous sandstone section of large section tunnel

2019 ◽  
Vol 136 ◽  
pp. 04023
Author(s):  
Ming Zhao ◽  
Ke Li ◽  
Hong Yan Guo ◽  
KaiCheng Hua
Keyword(s):  
Limit State ◽  
Stable State ◽  
Simulation Software ◽  
Surrounding Rock ◽  
Large Section ◽  
Rock Stability ◽  
Geological Conditions ◽  
Construction Step ◽  
The Face ◽  
The Stability

Based on the special geological conditions of a tunnel in Qingyuan section of Huizhou-Zhanzhou Expressway, FLAC3d numerical simulation software is used to simulate the rheological properties and instability of surrounding rock in large-section fully weathered sandstone section, and the stability and loss of surrounding rock are analyzed. The deformation of the dome and the face at steady state is analyzed. It is found that: 1) when the surrounding rock is in a stable state, the deformation curve of the dome is smooth. When the surrounding rock of the face is unstable, the front of the face appears ahead. Deformation should be first strengthened on the surrounding rock in front of the face. 2) The arched foot is an important part of the instability of the surrounding rock. In order to prevent the expansion of the collapsed part, the arched part should be reinforced. 3) In order to obtain the limit state of surrounding rock stability, the strength of surrounding rock is reduced, and the strength reduction coefficient corresponding to the displacement sudden point is taken as the safety factor of rock stability around the hole, and the stability safety coefficients of surrounding rock of each construction step are greater than 1.2. 4) The dynamic standard values of deformation control in the whole construction stage are obtained by analyzing the deformation curves of each data monitoring point with time in the corresponding time period of each construction step.

Study on the coupling system of high prestress cable truss and surrounding rock on a coal roadway

2010 ◽  
pp. 643-646
Author(s):  
Fulian He ◽  
Dongping Ying ◽  
Hong Yan ◽  
Hongqiang Han ◽  
Kaiqing Li
Keyword(s):  
Surrounding Rock ◽  
Coal Roadway ◽  
Coupling System

scholarly journals An Experimental Research on Surrounding Rock Unloading during Solid Coal Roadway Excavation

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Hongjun Guo ◽  
Ming Ji ◽  
Dapeng Liu ◽  
Mengxi Liu ◽  
Gaofeng Li ◽  
...  
Keyword(s):  
Energy Storage ◽  
Deformation Energy ◽  
Surrounding Rock ◽  
Dissipated Energy ◽  
Rock Stress ◽  
Deformation And Failure ◽  
Coal Roadway ◽  
Solid Coal ◽  
Unloading Rate ◽  
Surrounding Rock Stress

In order to further explore the deformation and failure essence of the deep coal body, based on the characteristics of surrounding rock stress adjustment before and after solid coal roadway excavation, an experiment of unloading confining pressure and loading axial pressure of the coal body was designed and conducted in this study. Based on test results, the failure mechanics and energy characteristics of the coal body were analyzed through experiments. Rapid unloading is considered a key factor contributing to lateral deformation and expansion failure, which exacerbates the deterioration of coal body and reduces the deformation energy storage capacity of coal. On the other hand, the larger loading rate tends to shorten the accumulation time of microcracks and cause damage to the coal body, resulting in strengthening the coal body and improving energy storage. Under the circumstance that the coal body is destroyed, the conversion rates of the internal deformation energy and dissipated energy are more significantly affected by unloading rate. The increasing unloading rate and rapid decreases in the conversion rate of deformation energy make the coal body more vulnerable to damage. Under the same stress conditions, the excavation unloading is more likely to deform, destroy, or even throw the coal than the experiment unloading. In order to reduce or avoid the occurrence of deep roadway excavation accidents, the understanding of the excavation unloading including possible influencing factors and the monitoring of the surrounding rock stress and energy during the excavation disturbance should be strengthened. It can be used as the basis for studying the mechanism of deformation and failure of coal and rock and dynamic disasters in deep mines, as well as the prediction, early warning, prevention, and control of related dynamic disasters.

scholarly journals Experimental Test on Nonuniform Deformation in the Tilted Strata of a Deep Coal Mine

2021 ◽  
Vol 13 (23) ◽  
pp. 13280
Author(s):  
Hai Wu ◽  
Qian Jia ◽  
Weijun Wang ◽  
Nong Zhong ◽  
Yiming Zhao
Keyword(s):  
High Stress ◽  
Stability Control ◽  
Surrounding Rock ◽  
Experimental Results ◽  
Lower Side ◽  
Reinforcement Scheme ◽  
Deformation And Failure ◽  
True Triaxial ◽  
Deep Mine ◽  
Deep Coal Mine

Taking a deep-mine horizontal roadway in inclined strata as our research object, the true triaxial simulation technique was used to establish a model of the inclined strata and carry out high-stress triaxial loading experiments. The experimental results show that the deformation of surrounding rock in the roadway presents heterogeneous deformation characteristics in time and space: the deformation of the surrounding rock at different positions of the roadway occurs at different times. In the process of deformation of the surrounding rock, deformation and failure occur at the floor of the roadway first, followed by the lower shoulder-angle of the roadway, and finally the rest of the roadway. The deformation amount in the various areas is different. The floor heave deformation of the roadway floor is the greatest and shows obvious left-right asymmetry. The deformation of the higher side is greater than that of the lower side. The model disassembly shows that the development of cracks in the surrounding rock is characterized by more cracks on the higher side and fewer cracks on the lower side but shows larger cracks across the width. The experimental results of high-stress deformation of the surrounding rock are helpful in the design of supports, the reinforcement scheme, and the parameter optimization of roadways in high-stress-inclined rock, and to improve the stability control of deep high-stress roadways.

Sign in / Sign up

Export Citation Format

Share Document