Comparative Study of Different Source of Silica-Filled Epoxy Resin

2013 ◽  
Vol 631-632 ◽  
pp. 205-208 ◽  
Author(s):  
Shan Sun ◽  
Xue Qing Liu ◽  
Ji Yan Liu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Impact Strength ◽  
Rice Husk ◽  
Specific Area ◽  
Fume Silica ◽  
Rice Husk Silica ◽  
Scanning Electron ◽  
Better Than

The mechanical properties and morphologies of fume precipitate and rice husk silica filled EP composites have been compared. The density, specific area of the silica decreases in the order of fume silica, precipitate silica and rice husk silica, while the silica size increases with the order above. It is shown that the fume silica/EP exhibits the highest flexural strength and modulus, followed by the precipitate silica/EP and the rice husk silica/EP. The rice husk silica/EP exhibits the highest in impact strength as silica is 1 phr. Over 5 phr of silica, fume silica/EP has the highest in impact strength, while the rice silica/EP is better than precipitate silica/EP. Scanning electron microscopy (SEM) results show that the fume silica has best dispersion and least filler agglomerates in matrix. The better dispersion will be responsible for the higher reinforcing and processing viscosity of the fume silica.

Mechanical Properties and Morphologies of Rice Husk Silica/Epoxy Nanocomposites

2011 ◽  
Vol 236-238 ◽  
pp. 220-224 ◽  
Author(s):  
Xue Qing Liu ◽  
Ji Yan Liu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Specific Surface ◽  
Rice Husk ◽  
Silica Content ◽  
Flexural Test ◽  
Neat Resin ◽  
Rice Husk Silica ◽  
Scanning Electron

Amorphous rice husk silica with purity of 99.3% and the specific surface area value of 212 mP2P/g was obtained by burning the dilute HCl treated rice husk at 600°C. After being modified with γ-glycidyloxipropyltrimethoxysilane (KH-550), silica particles with size ranging from 30 to 50 nm were obtained and subsequently used as filler to prepare epoxy-based nanocomposites with 0, 1, 3, 5 and 10 wt% silica content. The mechanical properties of the nanocomposites were characterized in terms of tensile and flexural test. The morphologies of fracture surfaces of nanocomposites were investigated by scanning electron microscopy (SEM). Depending on the silica content, the stiffness, strength and toughness of the nanocomposites can be increased more or less compared with neat resin.

Electron Microscopic Observation of the Longitudinal Organization of Poly (p-Phenylene Terephthalamide) Fibers

1982 ◽  
Vol 40 ◽  
pp. 680-681
Author(s):  
Li Li-Sheng ◽  
L.F. Allard ◽  
W.C. Bigelow
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Microscopic Observation ◽  
Electron Microscopic Observation ◽  
Electron Microscopic ◽  
Aromatic Polyamides ◽  
Radial Arrangement ◽  
Scanning Electron ◽  
Better Than

The aromatic polyamides form a class of fibers having mechanical properties which are much better than those of aliphatic polyamides. Currently, the accepted morphology of these fibers as proposed by M.G. Dobb, et al. is a radial arrangement of pleated sheets, with the plane of the pleats parallel to the axis of the fiber. We have recently obtained evidence which supports a different morphology of this type of fiber, using ultramicrotomy and ion-thinning techniques to prepare specimens for transmission and scanning electron microscopy.

scholarly journals Simultaneous Improvement in the Tensile and Impact Strength of Polypropylene Reinforced by Graphene

2020 ◽  
Vol 2020 ◽  
pp. 1-5
Author(s):  
Li Juan
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Fracture Surface ◽  
Impact Strength ◽  
Melt Blending ◽  
Elongation At Break ◽  
Morphological Behavior ◽  
Scanning Electron

The nanocomposites of polypropylene (PP)/graphene were prepared by melt blending. The effects of the dosage of graphene on the flow and mechanical properties of the nanocomposites were investigated. The morphologies of fracture surfaces were characterized through scanning electron microscopy (SEM). The graphene simultaneous enhanced tensile and impact properties of nanocomposites. A 3.22% increase in tensile strength, 39.8% increase in elongation at break, and 26.7% increase in impact strength are achieved by addition of only 1 wt.% of graphene loading. The morphological behavior indicates the fracture surface of PP/graphene is more rough than that of pure PP.

scholarly journals PENGARUH LIMBAH ABU PEMBAKARAN BIOMASSA KELAPA SAWIT TERHADAP SIFAT-SIFAT FISIKA DAN MEKANIK HIGH IMPACT POLYSTYRENE

2015 ◽  
Vol 4 (3) ◽  
pp. 23-28
Author(s):  
Fadhilla Asyri ◽  
Kartini Noor Hafni ◽  
A. Haris Simamora
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Impact Strength ◽  
Specific Gravity ◽  
Physical And Mechanical Properties ◽  
High Impact ◽  
Elongation At Break ◽  
Scanning Electron

This study aims was to determine the effect of palm oil fuel ash (POFA) composite as filler on the physical and mechanical properties of high impact polystyrene (HIPS) composites. The research methodology included preparation of raw materials, treatment POFA (hydration process of POFA), mixing using tumbler and then extruder, molding composite specimens, and testing. The variables used were weight ratio of HIPS with 140 mesh POFA at 95/5; 92.5/7.5; 90/10. The composites were tested by Fourier Transform Infrared (FTIR), ash content, specific gravity, tensile strength, elongation at break, impact strength, hardness test, and Scanning Electron Microscopy (SEM). The results of FTIR characterization shows the formation of –OH bonding that was suspected as Si-OH or Si-hydrat. Results of physical and mechanical properties of the composites shows that increase of the filler composition in HIPS-POFA composites until the ratio of 90/10, increase the specific gravity to 7.2% of the original, tensile strength did not change significantly to 28.4 MPa, elongation at break decreased to 2.7%, impact strength decreased to 3.183 KJ/m2, and the hardness increased to 110.5, and Scanning Electron Microscopy (SEM) test show the transformation of POFA structure on treated POFA and intercalation between the matrix and POFA.

Study on Preparation and Properties of Polystyrene/Styrene-Ethylene/Butylene-Styrene Composites

2011 ◽  
Vol 284-286 ◽  
pp. 1886-1889 ◽  
Author(s):  
Xiao Ming Sang ◽  
Lei Zhang ◽  
Run Zeng Wang ◽  
Xing Gang Chen ◽  
Man An ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Impact Strength ◽  
Melt Blending ◽  
Maximum Torque ◽  
Polystyrene Matrix ◽  
Blending Process ◽  
The Impact ◽  
Scanning Electron

The polystyrene/styrene-ethylene/butylene-styrene composites were prepared by melt blending process in this paper. The mechanical properties of PS/SEBS composites were analyzed. The results showed that the impact strength of PS/SEBS composites could be increased with the content increasing of SEBS, meanwhile the tensile strength was lower than pure polystyrene. When the content of SEBS increased to 13 wt.%, the impact strength of PS/SEBS composites was 2.4 times higher than that of pure PS. The fractured surfaces of the specimens were characterized by scanning electron microscopy(SEM). The results showed that the impact fractured surfaces produced a lot of sliding along with the addition of SEBS. The particles of SEBS could be well dispersed in polystyrene matrix. From rheological properties studies and the values of the torque, it was suggested that the maximum torque of PS/SEBS composites decreased drastically.

scholarly journals Analysis of PLA Composite Filaments Reinforced with Lignin and Polymerised-Lignin-Treated NFC

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2174
Author(s):  
Diana Gregor-Svetec ◽  
Mirjam Leskovšek ◽  
Blaž Leskovar ◽  
Urška Stanković Elesini ◽  
Urška Vrabič-Brodnjak
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Glassy State ◽  
Nanofibrillated Cellulose ◽  
Dynamic Mechanical Properties ◽  
Initial Modulus ◽  
Surface Modified ◽  
Scanning Electron

Polylactic acid (PLA) is one of the most suitable materials for 3D printing. Blending with nanoparticles improves some of its properties, broadening its application possibilities. The article presents a study of composite PLA matrix filaments with added unmodified and lignin/polymerised lignin surface-modified nanofibrillated cellulose (NFC). The influence of untreated and surface-modified NFC on morphological, mechanical, technological, infrared spectroscopic, and dynamic mechanical properties was evaluated for different groups of samples. As determined by the stereo and scanning electron microscopy, the unmodified and surface-modified NFCs with lignin and polymerised lignin were present in the form of plate-shaped agglomerates. The addition of NFC slightly reduced the filaments’ tensile strength, stretchability, and ability to absorb energy, while in contrast, the initial modulus slightly improved. By adding NFC to the PLA matrix, the bending storage modulus (E’) decreased slightly at lower temperatures, especially in the PLA samples with 3 wt% and 5 wt% NFC. When NFC was modified with lignin and polymerised lignin, an increase in E’ was noticed, especially in the glassy state.

scholarly journals Corrosion Behavior and Mechanical Properties of a Nanocomposite Superhydrophobic Coating

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 652
Author(s):  
Divine Sebastian ◽  
Chun-Wei Yao ◽  
Lutfun Nipa ◽  
Ian Lian ◽  
Gary Twu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Atomic Force Microscopy ◽  
Nanocomposite Coating ◽  
Superhydrophobic Coating ◽  
Force Microscopy ◽  
Atomic Force ◽  
Microscopy Images ◽  
Scanning Electron

In this work, a mechanically durable anticorrosion superhydrophobic coating is developed using a nanocomposite coating solution composed of silica nanoparticles and epoxy resin. The nanocomposite coating developed was tested for its superhydrophobic behavior using goniometry; surface morphology using scanning electron microscopy and atomic force microscopy; elemental composition using energy dispersive X-ray spectroscopy; corrosion resistance using atomic force microscopy; and potentiodynamic polarization measurements. The nanocomposite coating possesses hierarchical micro/nanostructures, according to the scanning electron microscopy images, and the presence of such structures was further confirmed by the atomic force microscopy images. The developed nanocomposite coating was found to be highly superhydrophobic as well as corrosion resistant, according to the results from static contact angle measurement and potentiodynamic polarization measurement, respectively. The abrasion resistance and mechanical durability of the nanocomposite coating were studied by abrasion tests, and the mechanical properties such as reduced modulus and Berkovich hardness were evaluated with the aid of nanoindentation tests.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

scholarly journals Effect of Annealing Process on the Mechanical Properties of X70 Pipeline Steel

2018 ◽  
Vol 186 ◽  
pp. 02001
Author(s):  
Teng-wei Zhu ◽  
Cheng-liang Miao ◽  
Zheng Cheng ◽  
Zhipeng Wang ◽  
Yang Cui ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Annealing Temperature ◽  
Pipeline Steel ◽  
Annealing Process ◽  
X70 Pipeline Steel ◽  
Grain Sizes ◽  
Scanning Electron

The influence of the mechanical properties of X70 pipeline steel under different annealing temperature was studied. The corresponding microstructure was investigated by the Field Emission Scanning Electron Microscopy. The results showed that the yield strength and the tensile strength both experienced from rise to decline with the increase of annealing temperature. The grain sizes were coarse and a large amount of cementite precipitated due to preserving temperature above 550 °, which induced matrix fragmentation and deteriorate the -10 ° DWTT Toughness. There were little changes on the microstructure and mechanical properties when the annealing temperature was under 500 °.

Hierarchical Design and Nanomechanics of the Calcified Byssus of Anomia simplex

2009 ◽  
Vol 1187 ◽  
Author(s):  
Jakob R Eltzholtz ◽  
Marie Krogsgaard ◽  
Henrik Birkedal
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Mechanical Performance ◽  
Blue Mussel ◽  
Hierarchical Design ◽  
Reduced Modulus ◽  
Different Types ◽  
Microscopy Images ◽  
Scanning Electron

AbstractBiology has evolved several strategies for attachment of sedentary animals. In the bivalves, byssi abound and the best known example being the protein-based byssus of the blue mussel and other Mytilidae. In contrast the bivalve Anomia sp. has a single calcified thread. The byssus is hierarchical in design and contains several different types of structures as revealed by scanning electron microscopy images. The mechanical properties of the byssus are probed by nanoindentation. It is found that the mineralized part of the byssus is very stiff with a reduced modulus of about 67 GPa and a hardness of ˜3.7 GPa. This corresponds to a modulus roughly 20% smaller than that of pure calcite and a hardness that is about 20% larger than pure calcite. The results reveal the importance of microstructure on mechanical performance.

Sign in / Sign up

Export Citation Format

Share Document