Variation in Fineness of Cement-Based Composites Containing Sugarcane Bagasse Ashes

2014 ◽  
Vol 894 ◽  
pp. 13-17 ◽  
Author(s):  
An Cheng ◽  
Wei Ting Lin ◽  
Sao Jeng Chao ◽  
Hui Mi Hsu
Keyword(s):  
Compressive Strength ◽  
Sugarcane Bagasse ◽  
Pozzolanic Reaction ◽  
Partial Replacement ◽  
Cementitious Composites ◽  
Particle Sizes ◽  
Test Results ◽  
Activity Test ◽  
Compressive Strength Test ◽  
Sugarcane Bagasse Ash

This study is aimed to evaluate the effect of sugarcane bagasse ash fineness on the properties of cement-based composites. Three sugarcane bagasse ash contents (10, 20 and 30% by weight of cement) and three particle sizes of bagasse ash (particles less than 45, 75 and 150 μm) were used as a partial replacement for cement in mortar specimens with a constant water/cementitious ratio of 0.55. The pozzolanic strength activity test, compressive strength test and scanning electron microscope observations were conducted and compared. Test results indicated that the compressive strength decreased with the addition of sugarcane bagasse ash content increased. Addition of sugarcane bagasse ash to replace cement in cementitious composites could provide hydration and pozzolanic reaction, but it would still keep more rugged and some larger pores observed from the paste surface and resulted in the weaker microstructures and poorer properties in cementitious composites. In conclusion, the critical usage of sugarcane bagasse ash is 10 % with 45μm particles.

scholarly journals Utilization of Sugarcane Bagasse Ash from Power Co-generation Boilers as a Supplementary Cementitious Material

2021 ◽  
Vol 2 (2) ◽  
Author(s):  
Safiki Ainomugisha ◽  
Bisaso Edwin ◽  
Bazairwe Annet
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Sugarcane Bagasse ◽  
Low Income ◽  
Ordinary Portland Cement ◽  
Construction Material ◽  
Sustainable Construction ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Sugarcane Bagasse Ash

Concrete has been the world’s most consumed construction material, with over 10 billion tons of concrete annually. This is mainly due to its excellent mechanical and durability properties plus high mouldability. However, one of its major constituents; Ordinary Portland Cement is reported to be expensive and unaffordable by most low-income earners. Its production contributes about 5%–8% of global CO2 greenhouse emissions. This is most likely to increase exponentially with the demand of Ordinary Portland Cement estimated to rise by 200%, reaching 6000 million tons/year by 2050.  Therefore, different countries are aiming at finding alternative sustainable construction materials that are more affordable and offer greener options reducing reliance on non-renewable sources. Therefore, this study aimed at assessing the possibility of utilizing sugarcane bagasse ash from co-generation in sugar factories as supplementary material in concrete. Physical and chemical properties of this sugarcane bagasse ash were obtained plus physical and mechanical properties of fresh and hardened concrete made with partial replacement of Ordinary Portland Cement. Cost-benefit analysis of concrete was also assessed. The study was carried using 63 concrete cubes of size 150cm3 with water absorption studied as per BS 1881-122; slump test to BS 1881-102; and compressive strength and density of concrete according to BS 1881-116. The cement binder was replaced with sugarcane bagasse ash 0%, 5%, 10%, 15%, 20%, 25% and 30% by proportion of weight. Results showed the bulk density of sugarcane bagasse ash at 474.33kg/m3, the specific gravity of 1.81, and 65% of bagasse ash has a particle size of less than 0.28mm. Chemically, sugarcane bagasse ash contained SiO2, Fe2O3, and Al2O3 at 63.59%, 3.39%, and 5.66% respectively. A 10% replacement of cement gave optimum compressive strength of 26.17MPa. This 10% replacement demonstrated a cost saving of 5.65% compared with conventional concrete. 

BEHAVIOR OF M 50 GRADE SELF-COMPACTING CONCRETE DEVELOPED USING PORTLAND SLAG CEMENT AND METAKAOLIN

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Sravya Nalla ◽  
Janardhana Maganti ◽  
Dinakar Pasla
Keyword(s):  
Compressive Strength ◽  
Mineral Admixtures ◽  
Partial Replacement ◽  
Test Results ◽  
Slag Cement ◽  
Self Compacting Concrete ◽  
Destructive Testing ◽  
Compressive Strength Test ◽  
Portland Slag Cement ◽  
Strength And Durability

Self-compacting concrete (SCC) is a revolutionary development in concrete construction. The addition of mineral admixtures like metakaolin, which is a highly reactive pozzolana to the SCC mixes, gives it superior strength and durability. The present work is an effort to study the behavior of M50 grade SCC by partial replacement of Portland Slag Cement (PSC) with metakaolin. Its strength and durability aspects are comparable with a controlled concrete (without replacement of cement). In the present work, a new mix design methodology based on the efficiency of metakaolin is adopted. The optimum percentage replacement of cement with metakaolin is obtained based on compressive strength test results. The influence of metakaolin on the workability, compressive strength, splitting tensile strength and flexural strength of SCC and its behavior when subjected to elevated temperature was investigated through evaluation against controlled concrete and non-destructive testing. From the test results, it was observed that incorporation of metakaolin at an optimum dosage satisfied all the fresh properties of SCC and improved both the strength and durability performance of SCC compared to controlled concrete.

Influence of Physicochemical Properties of Sugarcane Bagasse Ash (SCBA) in Portland Cement Hydration

2018 ◽  
Vol 765 ◽  
pp. 324-328
Author(s):  
Tiago Assunção Santos ◽  
José da Silva Andrade Neto ◽  
Vitor Souza Santos ◽  
Daniel Véras Ribeiro
Keyword(s):  
Portland Cement ◽  
Sugarcane Bagasse ◽  
Cement Hydration ◽  
New Technologies ◽  
Pozzolanic Reaction ◽  
Cement Industry ◽  
Partial Replacement ◽  
Cement Pastes ◽  
Sugarcane Bagasse Ash ◽  
Portland Cement Hydration

Due to the concern with the environmental impacts caused by the gases emitted by the cement industry and by the inadequate disposal of wastes generated in the sugar-alcohol industry, such as sugarcane bagasse ash (SCBA), a search for the development of new technologies, which are less aggressive to the environment and that propose feasible alternatives, began in order to reuse these wastes properly. Among these alternatives is the reuse of SCBA as partial replacement to cement or as addition to cementitious matrices. In this way, the present research has the objective of analyzing the influence of SCBA obtained by the calcination of sugarcane bagasse (SCB), at 600°C, in the process of Portland cement hydration. Initially, the SCBA was characterized physically, chemically and mineralogically, and then cement pastes with 20% and 35% substitution contents were elaborated, besides the reference paste, which were analyzed through X-ray diffraction (XRD) and thermogravimetric (TG) techniques. The results obtained show that there is a consumption of portlandite as a consequence of the use of SCBA, evidencing the pozolanicity of these ashes. In the pastes with 35% substitution content, there was an intense consumption of the portlandite, indicating, in this proportion, the pozzolanic reaction was more intense.

scholarly journals Potency Of Sugarcane Bagasse Ash Partial Substitution Of Cement In Concrete

2019 ◽  
Author(s):  
Ismail Marzuki ◽  
Erniati Bachtiar ◽  
ASRI MULYA SETIAWAN ◽  
SRIGUSTY
Keyword(s):  
Compressive Strength ◽  
Sugarcane Bagasse ◽  
Construction Material ◽  
Standard Condition ◽  
Strength Test ◽  
Test Method ◽  
Partial Substitution ◽  
Sugar Factory ◽  
Compressive Strength Test ◽  
Sugarcane Bagasse Ash

the availability of sugarcane bagasse ash produced by Arasoe Sugar Factory, it is not used utilized. That sugarcane bagasse ash has size very fine that it can pollute the air. The sugarcane bagasse ash has silicate content, and it has pozzolan properties. The needs of construction material are something that to think about that. It is an alternative to substitute the using of cement in concrete construction. This study is aimed to find the potential of sugarcane bagasse ash in Arasoe Sugar Factory for partial substitution of cement in concrete. The sample made from the variety of sugarcane bagasse ash 0%, 2.5%, 5%, and 7.5% as partial substitution of cement in concrete. The ratio of water and cement is 0.45. The specimen of concrete is taken care in standard condition at the laboratory and compressive strength test when the sample is in 28, 45, and 62 days old. The compressive strength test refers to ASTM C39/ C39M-01 (Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens). The development of compressive strength of concrete with many variations of sugarcane bagasse ash 0% 2.5%, 5% is increasing along with the age of concrete, however in contrast with 7.5% of sugarcane bagasse ash the decreasing in 60 days old later. Partial substitute of sugarcane bagasse ash in concrete is possible to do in an amount about 5% of sugarcane bagasse ash

scholarly journals An Experimental Investigation on Concrete by Partially Replacing Cement Using Bagasse Ash Powder

2021 ◽  
pp. 414-426
Author(s):  
Manish Ram E ◽  
Sindhu Vaardhini U
Keyword(s):  
Experimental Investigation ◽  
Compressive Strength ◽  
Sugarcane Bagasse ◽  
Setting Time ◽  
Mineral Admixtures ◽  
Partial Replacement ◽  
Waste Products ◽  
Agricultural Industry ◽  
Sugarcane Bagasse Ash ◽  
The Impact

Utilization of the waste products in the agricultural industry has been the focus of Research for economic, environmental, and technical reasons. Sugarcane Bagasse Ash (SCBA) is one of the promising material, with its potential proved to be used as a partial replacement of cement as well as mineral admixtures for producing concrete; properties of such concrete depend on the chemical composition, fineness, specific surface area of SCBA. An experimental investigation will be carried out to examine the impact of replacing cement by bagasse ash to the mechanical and physical properties of pastes and mortars, fresh and harden concrete such as consistency, setting time and workability, compressive strength. Sugarcane Bagasse Ash powder used by replacing fly ash at 40%, 50%, and 60%. Compressive strength and water absorption test will be carried out for evaluating the performance of the material.

Influence of Fly Ash on the Mechanical Properties of Engineered Cementitious Composites Cured at High Temperature

2010 ◽  
Vol 113-116 ◽  
pp. 1293-1296
Author(s):  
Yu Zhu ◽  
Ying Zi Yang ◽  
Hong Wei Deng ◽  
Yan Yao
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
High Volume ◽  
Bending Test ◽  
Cementitious Composites ◽  
Test Results ◽  
Four Point Bending ◽  
High Volume Fly Ash ◽  
Compressive Strength Test

In order to investigate the mechanical properties of cementitious composites (ECC) cured at 60°C, four-point bending test and compressive strength test are employed to analyze the effect of fly ash on the properties of ECC. The replacement ratio of cement with fly ash is 50%, 70% and 80%, respectively. The test results indicate that ECC with high volume fly ash still remain the characteristic of pseudo-strain hardening and the deflection of ECC increases remarkably by adding more fly ash. The observations of ECC indicate that the crack width is relatively smaller for higher volume fly ash ECC. Meanwhile, compressive strength of ECC specimens with 80% fly ash can reach to 70MPa. This is helpful to produce precast ECC with high volume of fly ash.

Influence of Metakaolin on Strength and Microstructure of Steam-Cured High-Strength Concrete

2013 ◽  
Vol 838-841 ◽  
pp. 42-46 ◽  
Author(s):  
Jun Jie Zeng ◽  
Zhi Hong Fan ◽  
Long Chen
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Pozzolanic Reaction ◽  
Early Age ◽  
Test Results ◽  
Replacement Level ◽  
Strength Concrete ◽  
Pozzolanic Reactivity ◽  
Compressive Strength Test

The influence of metakaolin (MK) on strength and microstructure of steam-cured high-strength concrete has been investigated using compressive strength test, XRD, MIP and SEM. Three MK replacement levels were considered in the study: 5%, 10% and 15% by weight of cement. A mix double blended with 10% MK and 10% slag was prepared too. Test results have indicated that MK can increase the compressive strength of steam-cured concrete, especially at early age. Compressive strength up to 90MPa at 1 and 28 days is obtained with the incorporation of 10% MK and 10% slag. When the replacement level of MK is higher than 10%, the enhancement of strength becomes less significant. Content of Ca (OH)2 crystals is decreased while content of hydrates with Al is increased due to the pozzolanic reactivity of MK. Concrete pore structure is significantly refined and a denser hydrates structure is obtained due to the pozzolanic reaction and filler effect of MK. Meanwhile, combination of aggregate and paste is enhanced too. The improvements of strength and microstructure become more obvious when MK and slag are double incorporated.

scholarly journals Waste tires and the burning of sugarcane bagasse in the manufacture of concrete pavers (pavers)

2019 ◽  
Vol 12 (3) ◽  
pp. 608-637
Author(s):  
S. P. S. ALTOÉ ◽  
A. SALES ◽  
C. H. MARTINS
Keyword(s):  
Compressive Strength ◽  
Natural Resources ◽  
Sugarcane Bagasse ◽  
Abrasion Resistance ◽  
Partial Replacement ◽  
Natural Sand ◽  
Small Aggregate ◽  
Sugarcane Bagasse Ash

Abstract The research developed has the purpose of analyzing the potential utilization of sugarcane bagasse ash and tire residue in the construction of pavers in replacement of the small aggregate, the natural sand. In order to achieve this objective, the methodology adopted includes steps such as: characterization of the residues to be used, preparation of pavers with different contents of partial replacement of small aggregates, determination of the main pavers characteristics (compressive strength, water absorption, abrasion resistance) . The results proved the viability of the substitution, and the optimum content for the manufacturing of the parts is 27%, being 25% of BCC and 2% of tires. The contribution of the research is focused on reducing the consumption of natural resources and the correct disposal of the residues studied.

scholarly journals Pozzolanic and mechanical properties of Date Palm Seed Ash (Dpsa) concrete

2020 ◽  
Vol 39 (3) ◽  
pp. 680-686
Author(s):  
A.S.J. Smith ◽  
G. Xu ◽  
M.J. Garba ◽  
M.Y. Aliyu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Date Palm ◽  
Activity Index ◽  
Strength Test ◽  
Partial Replacement ◽  
Test Results ◽  
Setting Times ◽  
Compressive Strength Test

This paper presents the findings of a research work conducted on how to improve the mechanical properties of concrete using Date Palm Seed Ash (DPSA) as partial replacement of cement. The DPSA used was obtained by controlled burning of date palm seed in a kiln at a maximum temperature of 630oC for eight hours and air cooled afterwards. The ash obtained was sieved through 75μm sieve and its oxide composition analysed using X-ray fluorescence (XRF) procedures. DoE method of mix design was used to produce concrete ingredients for grade 30N/mm2 giving a water-cement ratio of 0.53. The effect of partial replacement of cement with DPSA on cement paste and concrete using 0, 2.5, 5, 7.5, 10, 15 and 20% DPSA was investigated through consistency and setting times tests, workability test, compressive strength test (at 7, 21, 28 and 56 days curing duration), pozzolanic activity index evaluation and water absorption test. Results show that DPSA has high silicon dioxide (45.50%), aluminum oxide (20.75%) and Iron oxide (7.25%). Findings indicate that the consistency and setting times of cement-DPSA paste increased with increase in the replacement of cement with DPSA. The workability of DPSA concrete decreased with increase in cement replacement. Compressive strength test results show that cement can be replaced with DPSA up to 10% as the compressive strength at 10% replacement is 31.5N/mm2 as against the 31N/mm2 of the normal concrete, at 56 days. The pozzolanic activity index result also show that DPSA concrete meets up the minimum requirement of 75% specified by ASTM C618-15. Also, the water absorption capacity of DPSA concrete at the highest replacement (20%) is 11% less than that at 0%. Keywords: Cement, Compressive strength, Concrete, Date palm seed ash, Partial replacement, Pozzolana

scholarly journals Strength analysis of soil blocks admixed with sugarcane bagasse ash.

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Shwetha Prasanna ◽  
Swaroopa Sail ◽  
Rhea Patil ◽  
Maryann De Souza ◽  
Anushuka Prasad ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Sugarcane Bagasse ◽  
Testing Machine ◽  
Partial Replacement ◽  
Strength Analysis ◽  
Fine Grained ◽  
Soil Cement ◽  
Laboratory Test Results ◽  
Fine Grained Soil ◽  
Sugarcane Bagasse Ash

This paper is mainly focusing on the stabilization of soil using sugarcane baggase ash (SBA) as a soil stabilizer. The locally available soil samples were collected and their properties were determined. Based on the laboratory test results the soil was classified as fine-grained soil. Soil stabilized blocks of dimensions 15cm x 15cm x 15cm were prepared with the following soil, cement and SBA combinations 100% soil, 80% soil + 20% cement, 80% soil +10% cement +10% SBA, 80% soil + 8% cement+ 12% SBA and 80% soil + 6% cement +14% SBA. Plain OPC cement of 43 grade and SBA from sugar factory Goa was used for the soil blocks. The blocks were moist cured for a period of 28 days. The soil stabilized blocks were then tested for their compressive strength under the universal testing machine according to BIS specifications. The effects of the SBA on the strength of the soil blocks were studied and it could be concluded that SBA can be used as a partial replacement of cement. Key words: sugarcane bagasse ash, compressive Strength, soil stabilized block, cement.

Sign in / Sign up

Export Citation Format

Share Document