A Study on Austenite Catalytic Cryogenic Treatment of Cr-W-Mo-V High Alloy Medium-Upper Carbon Steel

2014 ◽  
Vol 936 ◽  
pp. 1173-1178
Author(s):  
Yong Qing Ma ◽  
Xiao Jing Zhang ◽  
Yu Fen Liang ◽  
Guo Fang Liu
Keyword(s):  
Carbon Steel ◽  
Retained Austenite ◽  
Precipitation Hardening ◽  
Cryogenic Treatment ◽  
Residual Austenite ◽  
Carbon Steels ◽  
High Alloy ◽  
Austenite Transformation ◽  
Quenching And Tempering ◽  
Better Than

The processing of austenite catalytic cryogenic treatment of two components of Cr-W-Mo-V high alloy medium-upper carbon steels and the effect on the retained austenite transformation and tempering hardness were studied in this paper. The results show that, the effect of austenite catalytic cryogenic treatment of Cr-W-Mo-V high alloy medium-upper carbon steel is better than that of direct cryogenic treatment after quenching, and the content of residual austenite reduced to below 5%, and the hardness improved by 1.5HRC than that of conventional quenching and tempering. The retained austenite catalytic temperature of Cr-W-Mo-V high alloy medium-upper carbon steel merely is higher than 10°C~20°C of the temperature for the highest tempering hardness. Catalytic temperature Tc can be determined by experimental method of conventional quenching and tempering of the steel, in which the microstructure feature is precipitation of M3C carbide particle of 0.01μm~0.03μm in martensite matrix, and the content of retained austenite decreases evidently. By cryogenic treatment after the austenite catalyzed the retained austenite of quenching are transformed into more martensite, and in the subsequent tempering processing the original quenching martensite and the martensite from retained austenite transformation almost will form synchronous precipitation hardening. Thus the tempering hardness improves evidently as well.

Precipitation and Precipitation Hardening Behavior of V and/or Cu Bearing Middle Carbon Steels

2010 ◽  
Vol 638-642 ◽  
pp. 3491-3495 ◽  
Author(s):  
Takehide Senuma ◽  
Masanori Sakamoto ◽  
Yoshito Takemoto
Keyword(s):  
Carbon Steel ◽  
Precipitation Hardening ◽  
Bearing Steel ◽  
Carbon Steels ◽  
Precipitation Behavior ◽  
Hardening Behavior ◽  
Precipitation Treatment ◽  
Interphase Precipitation

In this study, the precipitation and precipitation hardening behavior of a 0.3%V and 2%Cu bearing middle carbon steel has been investigated in comparison with that of a 0.3%V bearing steel and a 2%Cu bearing steel. The precipitation treatment was carried out isothermally at 600°C.The amount of the precipitation hardening of the 0.3%V and 2%Cu bearing steel is nearly equal to the sum of the precipitation hardening of the 0.3%V bearing steel and the 2%Cu bearing steel In the 0.3%V bearing steel, precipitates were observed in rows, which indicates the occurrence of the interphase precipitation while precipitates observed in the 2%Cu bearing steel were randomly dispersed. In the V and Cu bearing steel, randomly dispersed precipitates were not observed where there were aligned precipitates. In the paper, the different precipitation behavior of the three steels is discussed.

scholarly journals Examination of Heat Treatment on the Microstructure and Wear of Tool Steels

2019 ◽  
Vol 2 (2) ◽  
pp. 87-92
Author(s):  
Enikő Réka Fábián ◽  
László Tóth ◽  
Csenge Huszák
Keyword(s):  
Wear Resistance ◽  
Retained Austenite ◽  
Cryogenic Treatment ◽  
Residual Austenite ◽  
Tool Steels ◽  
Austenite Content ◽  
The Matrix ◽  
Primary Carbides ◽  
Matrix Hardness ◽  
Multiple Tempering

Abstract The microstructure of the investigated X153CrMoV12 grade tool steel in delivered condition consisted of spheroidal matrix and primary carbides. The primary carbides were not dissolved under austenitisation time on either 1030°C or 1070°C. The microstructure and abrasion resistance of the steel changed due to quenching from different austenitisation temperatures. After conventional quenching from the higher austenitising temperature, there is more residual austenite in the steel than at quenching from the lower austenitisation temperature, which decreased the wear resistance. As a result of quenching from 1070°C followed by a multiple tempering process around 500 to 540°C, the retained austenite content is reduced and finely dispersed carbides are precipitated in the matrix, resulting in a higher matrix hardness and an increased wear resistance. After cryogenic treatment, the residual austenite content decreases compared to the conventional process, which leads to an increase in hardness and wear resistance.

New Development and Application of Microalloyed Medium Carbon Steel for Auto Forging Products

2012 ◽  
Vol 706-709 ◽  
pp. 2842-2847 ◽  
Author(s):  
Ying Jian Zhang ◽  
Han Dong ◽  
Wei Jun Hui ◽  
Jun Peng
Keyword(s):  
Carbon Steel ◽  
New Technologies ◽  
Medium Carbon Steel ◽  
Carbon Steels ◽  
Connecting Rod ◽  
Medium Carbon ◽  
New Development ◽  
The Cost ◽  
Processing Properties ◽  
Quenching And Tempering

Microalloyed medium carbon steels have been applied for auto forging products at the aim of lower cost since 1980’s in China. Without quenching and tempering processes, the cost of heat treatment was greatly decreased, so they are widely applied in car forgings such as crankshaft, connecting rod. Recently, with the aim of improving performance and reducing production cost, new technologies, such as: reductions of microalloyed elements, tailored components, and mechanical properties forecast, have been developed in China auto industry. The designation, processing, properties prediction and microstructure of auto components have been controlled comprehensively. With the development of new technologies, microalloyed medium carbon steel gradually began to be applied to product important parts, and replace Quenching and Tempering steels. Both steel makers and end product users are expressed their desire to share benefits of technological innovation. The technologies will have a huge developing space and very bright developing prospects in motor parts industry in future.

Investigation of Lath and Plate Martensite in a Carbon Steel

2011 ◽  
Vol 172-174 ◽  
pp. 61-66 ◽  
Author(s):  
Albin Stormvinter ◽  
Annika Borgenstam ◽  
Peter Hedström
Keyword(s):  
Carbon Steel ◽  
Carbon Content ◽  
Morphological Change ◽  
Retained Austenite ◽  
Alloy Composition ◽  
Lath Martensite ◽  
Carbon Steels ◽  
Plate Martensite ◽  
High Carbon ◽  
Martensite Microstructure

Martensite in carbon steels forms in different morphologies, often referred to as lath andplate martensite. The alloy composition has a strong effect on the morphology, for instance in car-bon steels there is a morphological change of the martensite microstructure from lath martensite atlow carbon contents to plate martensite at high carbon contents. In the present work a decarburizedhigh-carbon steel, enabling the isolation of carbons' influence alone, has been studied in order to in-vestigate the changes in morphology and hardness. From the results it is concluded that there is acontinuous change of hardness with increased carbon content. The increasing hardness slows down atabout 0.6 wt%C before decreasing at higher carbon contents. This is in accordance with the change inmorphology since it was found that lath martensite dominates below 0.6 wt%C and the first units ofgrain boundary martensite and plate martensite appear above 0.6 wt%C. At high carbon contents thedominating morphology is plate martensite, but retained austenite is also present.

scholarly journals Influence of modes of thermal hardening and the subsequent cryogenic processing on structure and properties of steel 38Ni3CrMoV

2021 ◽  
Vol 98 (2) ◽  
pp. 14-22
Author(s):  
S.V. Bobyr ◽  
◽  
P.V. Krot ◽  
G.V. Levchenko ◽  
O.Ye. Baranovska ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Retained Austenite ◽  
Thermal Stresses ◽  
Cryogenic Treatment ◽  
Steel Structure ◽  
Residual Austenite ◽  
Machine Building ◽  
Isothermal Quenching ◽  
Complex Alloy ◽  
Alloy Steels

For the production of various machine-building products - rolling rolls, parts of power equipment, piercing mandrels - complex alloy steels containing chromium and a significant number of other deficient alloying elements (nickel, vanadium, molybdenum) type 38Ni3CrMoV are used. The paper presents the results of research on the influence of modes of hardening and subsequent cryogenic treatment on the parameters of the structure, hardness and wear resistance of this steel. Visible changes in the microstructure of thermally improved steel samples during cryogenic treatment were not found, which can be explained by the high thermodynamic stability of the sorbitol structure and the practical absence of residual austenite due to its decomposition during high tempering. It is shown that cryogenic treatment of thermally improved 38Ni3CrMoV steel contributes to an increase in the hardness, toughness and wear resistance this steel (~3.8 %). In this case, there is a slight increase in the parameter and magnitude of microstresses of the crystal lattice, an increase in the density of dislocations due to the removal of thermal stresses. To obtain a multiphase structure of 38Ni3CrMoV steel with retained austenite, isothermal quenching from the γ - α region has been proposed. The use of cryogenic treatment for the experimental mode of hardening of 38Ni3CrMoV steel samples promotes the transformation of retained austenite in the final structure of the samples into martensite with a significant increase in the microhardness of its structural components at the 22.3 %. The experimental hardening mode + cryogenic treatment provides a significant increase in the hardness and wear resistance of 38Ni3CrMoV steel at the 21.6 % while ensuring a certain level of its impact toughness (more than 4 J/cm2) and can be recommended for the implementation of the technology of differentiated hardening of large-sized products made of 38Ni3CrMoV steel. Keywords: steel, structure, hardness, wear resistance, isothermal hardening, cryogenic treatment.

INFLUENCE THE QUENCHING AND TEMPERING ON THE MICROSTRUCTURE, MECHANICAL PROPERTIES AND SURFACE ROUGHNESS, OF MEDIUM CARBON STEEL

2018 ◽  
Vol 18 (1) ◽  
pp. 125-135
Author(s):  
Sattar H A Alfatlawi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Surface Roughness ◽  
Carbon Steel ◽  
Cold Water ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Heating And Cooling ◽  
Treatment Processes ◽  
Quenching And Tempering

One of ways to improve properties of materials without changing the product shape toobtain the desired engineering applications is heating and cooling under effect of controlledsequence of heat treatment. The main aim of this study was to investigate the effect ofheating and cooling on the surface roughness, microstructure and some selected propertiessuch as the hardness and impact strength of Medium Carbon Steel which treated at differenttypes of heat treatment processes. Heat treatment achieved in this work was respectively,heating, quenching and tempering. The specimens were heated to 850°C and left for 45minutes inside the furnace as a holding time at that temperature, then quenching process wasperformed in four types of quenching media (still air, cold water (2°C), oil and polymersolution), respectively. Thereafter, the samples were tempered at 200°C, 400°C, and 600°Cwith one hour as a soaking time for each temperature, then were all cooled by still air. Whenthe heat treatment process was completed, the surface roughness, hardness, impact strengthand microstructure tests were performed. The results showed a change and clearimprovement of surface roughness, mechanical properties and microstructure afterquenching was achieved, as well as the change that took place due to the increasingtoughness and ductility by reducing of brittleness of samples.

UNS G10210

Alloy Digest ◽  
1988 ◽  
Vol 37 (9) ◽  
Keyword(s):  
Fracture Toughness ◽  
Carbon Steel ◽  
Manganese Content ◽  
Heat Treating ◽  
Carbon Steels ◽  
High Manganese ◽  
Steel Mills ◽  
Cold Worked ◽  
Good Workability ◽  
High Manganese Content

Abstract UNS G10210 is a carbon steel of relatively high manganese content which increases hardenability and hardness over that of carbon steels of lower manganese. It combines good machinability, good workability (hot or cold) and good weldability. It is used in the annealed, hot-worked, normalized, cold-worked or water-quenched-and-tempered condition for many applications. It may be used in uncarburized applications and for components case-hardened by carburizing. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: CS-122. Producer or source: Carbon steel mills.

The Effects of Quenching and Tempering Treatment on the Hardness and Microstructures of a Cold Work Steel

2019 ◽  
Vol 4 (1) ◽  
pp. 286-294
Author(s):  
László Tóth ◽  
Réka Fábián
Keyword(s):  
Heat Treatment ◽  
Retained Austenite ◽  
Elevated Temperatures ◽  
Cryogenic Treatment ◽  
Cold Work ◽  
Chromium Steel ◽  
Primary Carbide ◽  
Tempering Temperature ◽  
Tempering Treatment ◽  
Primary Carbides

The X153CrMoV12 ledeburitic chromium steel characteristically has high abrasive wear resistance, due to their high carbon and high chromium contents with a large volume of carbides in the microstructure. This steel quality has high compression strength, excellent deep hardenability and toughness properties, dimensional stability during heat treatment, high resistance to softening at elevated temperatures. The higher hardness of cryogenic treated samples in comparison with conventional quenched samples mean lower quantity of retained austenite as at samples quenched to room temperature and tempered in similar condition. In the microstructure of samples were observed that the primary carbide did not dissolve at 1070°C and their net structure have not been changed during to heat treatment. During to tempering at high temperature the primary carbides have become more and more rounded. After low tempering temperature in martensite were observed some small rounded carbides also, increasing the tempering temperature the quantity of finely dispersed carbides increased, which result higher hardness. The important issues in heat treatment of this steels are the reduction or elimination of retained austenite due to cryogenic treatment.

Microstructure and Mechanical Properties of a Low-Carbon Steel Treated by One-Step Quenching and Partitioning Process

2014 ◽  
Vol 1082 ◽  
pp. 202-207 ◽  
Author(s):  
Shu Yan ◽  
Xiang Hua Liu
Keyword(s):  
Mechanical Properties ◽  
Carbon Steel ◽  
Microstructural Evolution ◽  
Retained Austenite ◽  
Uniform Elongation ◽  
Low Carbon Steel ◽  
Total Elongation ◽  
Low Carbon ◽  
Quenching And Partitioning ◽  
Partitioning Time

A low carbon steel was treated by quenching and partitioning (Q&P) process, and a detailed characterization of the microstructural evolution and testing of mechanical properties were carried out. The resulted mechanical properties indicate that with the partitioning time increasing, the tensile strength decreases rapidly first and then remains stable, and the total elongation increases first then decreases. The investigated steel subjected to Q&P process exhibits excellent products of strength and elongation (17.8-20.6 GPa•%). The microstructural evolution of martensite matrix during the partitioning step was observed, and the morphology and content of retained austenite were characterized. The working hardening behavior of the samples was analyzed, and the retained austenite with higher carbon content contributes to the uniform elongation more effectively.

Sign in / Sign up

Export Citation Format

Share Document