Effect of Annealing on Dielectric Property in Ni1-xCoxFe2O4 Nanoparticles Synthesized Using Albumen (egg white)

2009 ◽  
Vol 6 ◽  
pp. 205-213 ◽  
Author(s):  
S. Marutha Senthil ◽  
R. Jayaprakash ◽  
Sarabu Ramana Murthy ◽  
A.R. Phani ◽  
V.N. Singh ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Dielectric Constant ◽  
Dielectric Property ◽  
Annealing Temperature ◽  
Interfacial Polarization ◽  
Egg White ◽  
High Resistivity ◽  
Thermal Evaporation Method ◽  
X Ray

The nano crystalline nickel-cobalt ferrite using albumen (egg white) is synthesized by thermal evaporation method and its dielectric behaviour is analyzed for different annealing temperatures. The dielectric property of the sample is measured using impedance analyzer in the frequency range 1-100 MHz. The variation of dielectric constant and dissipation factor under different frequency for the samples at different annealing temperature are analyzed. A steady dielectric constant is observed for the sample annealed at 500°C. The dielectric constant obtained for this sample is low and it is in the range of 18.9 to 6.9 for different frequencies. This low value of dielectric constant shows the less interfacial polarization due to high resistivity which may be to the presence of a few Fe2+ ions. It is observed that the dispersion in dielectric constant by varying the annealing temperature is producing an intended result. The presence of constituent phases in Ni1-xCoxFe2O4 is confirmed by X-Ray Diffraction. The particle size for Ni1-xCoxFe2O4 obtained from Scherrer equation is found to be is 30nm. The morphology, particle size and percentage composition of elements are measured by employing Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-Ray Analysis spectrum (EDX).

Annealing Effects on the Physical and Magnetic Properties of Tb1.5Y1.5Fe5O12 Films Nanoparticles Prepared by Sol-Gel Method

2013 ◽  
Vol 756 ◽  
pp. 91-98 ◽  
Author(s):  
Ftema W. Aldbea ◽  
Noor Bahyah Ibrahim ◽  
Mustafa Hj. Abdullah
Keyword(s):  
Particle Size ◽  
Magnetic Properties ◽  
Annealing Temperature ◽  
Quartz Substrate ◽  
Sol Gel ◽  
Lattice Parameter ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Iron Garnet

Terbium –substituted yttrium iron garnet (Tb1.5Y1.5Fe5O12) films nanoparticles were successfully prepared by a sol-gel method. The films were deposited on the quartz substrate using spin coating technique. To study effect of annealing temperature, the annealing process was executed at 700, 800 and 900 °C in air for 2 hours. The X-ray diffraction (XRD) proved that the pure phase of garnet structure was detected for the film annealed at 900 °C. The lattice parameter increased with the increment of annealing temperature and the highest value of 12.35 Å was obtained at 900 °C. Field Emission Scanning Electron Microscope (FE-SEM) results showed that the particle size increased from 43nm to 56nm as annealing temperature increased from 700 to 900°C. The film’s thickness also affected by increasing of annealing temperature and become thin at 900 °C due to densification process occurred at high annealing temperature. The elemental compositions of the Tb1.5Y1.5Fe5O12 film were detected using an Energy Dispersive X-raySpectroscopy (EDX). Magnetic properties at room temperature were measured using a Vibrating Sample Magnetometer (VSM).The saturation magnetization Ms increased with the annealingtemperature and showed a high value of 104emu/cm3, but the coercivity Hc of the film was decreased due to the increment of the particle size. Normal 0 21 false false false MS X-NONE X-NONE MicrosoftInternetExplorer4 Terbium –substituted yttrium iron garnet (Tb1.5Y1.5Fe5O12) films nanoparticles were successfully prepared by a sol-gel method. The films were deposited on the quartz substrate using spin coating technique. To study effect of annealing temperature, the annealing process was executed at 700, 800 and 900°C in air for 2 hours. The X-ray diffraction (XRD) proved that the pure phase of garnet structure was detected for the film annealed at 900 °C. The lattice parameter increased with the increment of annealing temperature and the highest value of 12.35 Å was obtained at 900 °C. Field Emission Scanning Electron Microscope (FE-SEM) results showed that the particle size increased from 43nm to 56nm as annealing temperature increased from 700 to 900 °C. The film’s thickness also affected by increasing of annealing temperature and become thin at 900 °C due to densification process occurred at high annealing temperature. The elemental compositions of the Tb1.5Y1.5Fe5O12 film were detected using an Energy Dispersive X-ray Spectroscopy (EDX). Magnetic properties at room temperature were measured using a Vibrating Sample Magnetometer (VSM).The saturation magnetization Ms increased with the annealing temperature and showed a high value of 104emu/cm3, but the coercivity Hc of the film was decreased due to the increment of the particle size. st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

Effect of Synthesis Temperature on Particles Size and Morphology of Zirconium Oxide Nanoparticle

2017 ◽  
Vol 50 ◽  
pp. 18-31 ◽  
Author(s):  
Rudzani Sigwadi ◽  
Simon Dhlamini ◽  
Touhami Mokrani ◽  
Patrick Nonjola
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Zirconium Oxide ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Crystallite Sizes ◽  
Ft Ir

The paper presents the synthesis and investigation of zirconium oxide (ZrO2) nanoparticles that were synthesised by precipitation method with the effects of the temperatures of reaction on the particles size, morphology, crystallite sizes and stability at high temperature. The reaction temperature effect on the particle size, morphology, crystallite sizes and stabilized a higher temperature (tetragonal and cubic) phases was studied. Thermal decomposition, band structure and functional groups were analyzed by Brunauer-Emmett-Teller (BET), Scanning Electron Microscopy (SEM), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Thermo-gravimetric analysis (TGA) and Fourier transform infrared (FT-IR). The crystal structure was determined using X-ray diffraction. The morphology and the particle size were studied using (SEM) and (TEM). The shaped particles were confirmed through the SEM analysis. The transmission electron microscopic analysis confirmed the formation of the nanoparticles with the particle size. The FT-IR spectra showed the strong presence of ZrO2 nanoparticles.

scholarly journals Study of Detector-Grade CdMnTe:In Crystals Obtained by a Multi-Step Post-Growth Annealing Method

Crystals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 387 ◽  
Author(s):  
Pengfei Yu ◽  
Yongren Chen ◽  
Wei Li ◽  
Wenfei Liu ◽  
Bin Liu ◽  
...  
Keyword(s):  
Annealing Temperature ◽  
Crystal Quality ◽  
High Resistivity ◽  
Detector Performance ◽  
Rocking Curve ◽  
X Ray ◽  
Annealing Step ◽  
Subsequent Step ◽  
Te Inclusions ◽  
Annealing Method

A multi-step annealing method was successfully applied to inclusions reduction and resistivity improvement of CdMnTe:In (CMT:In) single crystals with high resistivity, including a Cd atmosphere annealing step followed by a Te atmosphere annealing step. After the Cd atmosphere annealing step, the density of Te inclusions was reduced distinctly, and it could be also decreased in the subsequent step of re-annealing under Te atmosphere. Both the resistivity and IR transmittance decreased notably after Cd atmosphere annealing, whereas they increased tremendously after re-annealing under a Te atmosphere. The reduction of full-width at-half-maximum (FWHM) and the increase of the intensity of the X-ray rocking curve indicated an improvement of the crystal quality. Meanwhile, after Cd atmosphere annealing, the increase of the intensity of the (D0,X) peak and the disappearance of the (A0,X) peak in photoluminescence (PL) measurements suggested further that the crystal quality was improved. The detector performance was enhanced obviously after annealing. The higher the annealing temperature, the better the performance was. The detector fabricated by CMT:In slice (Cd atmosphere annealing at 1073 K for 240 h and Te atmosphere re-annealing at 773 K for 120 h) with 9.43% energy resolution and 1.25 × 10−3 cm2/V μτ value had the best detector performance.

Effect of Seedings on the Microstructure of Hydrated Alumina

2012 ◽  
Vol 554-556 ◽  
pp. 709-713
Author(s):  
Yan Hong Liu ◽  
Hong Wen Ma ◽  
Mei Tang Liu
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Decisive Role ◽  
Mechanism Study ◽  
Hydrated Alumina ◽  
Crystal Nucleus ◽  
X Ray ◽  
Intrinsic Mechanism ◽  
Scanning Electron

The morphology and particle size of boehmite play a decisive role on the application of alumina that derived from it. In this paper, we employed pseudoboehmite that produced from Al2 (SO4)3•18H2O and NH3•H2O at 70 °C, pH 7.5 as precursor to synthesize boehmite, and utilized different seeding when preparing pseudoboehmite and boehmite. To identify the influence of seeding on the microstructure of pseudoboehmite and boehmite, the products were characterized by X-ray powder diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and BET. The results indicate that the pseudoboehmite seeding has a significant influence on the morphology and particle size of pseudoboehmite to which we should pay high attention. However, the boehmite seeding does not play the role of crystal nucleus as expected. The further intrinsic mechanism study is ongoing.

scholarly journals A Study on the Characteristics of Cu–Mn–Dy Alloy Resistive Thin Films

Coatings ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 118 ◽  
Author(s):  
Ho-Yun Lee ◽  
Chi-Wei He ◽  
Ying-Chieh Lee ◽  
Da-Chuan Wu
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Annealing Temperature ◽  
Phase Evolution ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
Temperature Coefficient Of Resistance ◽  
X Ray ◽  
Transmission Electronmicroscopy ◽  
Scanning Electron

Cu–Mn–Dy resistive thin films were prepared on glass and Al2O3 substrates, which wasachieved by co-sputtering the Cu–Mn alloy and dysprosium targets. The effects of the addition ofdysprosium on the electrical properties and microstructures of annealed Cu–Mn alloy films wereinvestigated. The composition, microstructural and phase evolution of Cu–Mn–Dy films werecharacterized using field emission scanning electron microscopy, transmission electronmicroscopy and X-ray diffraction. All Cu–Mn–Dy films showed an amorphous structure when theannealing temperature was set at 300 °C. After the annealing temperature was increased to 350 °C,the MnO and Cu phases had a significant presence in the Cu–Mn films. However, no MnO phaseswere observed in Cu–Mn–Dy films at 350 °C. Even Cu–Mn–Dy films annealed at 450 °C showedno MnO phases. This is because Dy addition can suppress MnO formation. Cu–Mn alloy filmswith 40% dysprosium addition that were annealed at 300 °C exhibited a higher resistivity of ∼2100 μΩ·cm with a temperature coefficient of resistance of –85 ppm/°C.

Phase Development and Dielectric Properties of 0.98BaTiO3-0.02Ba (Mg1/3Nb2/3) O3 Ceramic

2011 ◽  
Vol 700 ◽  
pp. 58-62
Author(s):  
Rachanusorn Roongtao ◽  
Supagorn Rugmai ◽  
Wanwilai C. Vittayakorn
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Dielectric Constant ◽  
Dielectric Properties ◽  
Loss Factor ◽  
X Ray Diffraction ◽  
Phase Purity ◽  
X Ray ◽  
Phase Development ◽  
Scanning Electron

The 0.98BaTiO3-0.02Ba (Mg1/3Nb2/3) O3ceramics has been synthesized through a conventional mixed-oxide by using BT nanopowder and BMN micropowder. The phase purity of the powders and the ceramics was examined using X-ray diffraction (XRD). The 0.98BT-0.02BMN powders were sintered to 92% of the theoretical density at a temperature of 1300 °C for 2 h. The microstructure of the sintered surface was investigated using scanning electron microscopy (SEM). The dielectric constant (εr) and loss factor (tanδ) of the sintered pellets at Curie temperture were 3000 and 0.015, respectively.

scholarly journals Hydrothermal synthesis and characteristics of lanthanumdoped pb(Zr₀.₆₅Ti ₀.₃₅)O₃ ceramics

2021 ◽  
Vol 8 (3) ◽  
pp. 14-19
Author(s):  
Thuy Nguyen Thanh ◽  
Tung Nguyen Van ◽  
Hung Nguyen Trong ◽  
Minh Cao Duy
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Dielectric Constant ◽  
Reaction Temperature ◽  
Lead Zirconate Titanate ◽  
Lead Zirconate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Influence Of Ph ◽  
Scanning Electron

Lanthanum-doped lead zirconate titanate (PLZT) powders were synthesized using thehydrothermal method. The influence of pH, reaction temperature and time, lanthanum concentration on the formation and characteristics of PLZT were investigated. Obtained powders were investigated using X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) techniques and a dielectric analyzer. The results showed that           Pb1-xLax(Zr0.65Ti0.35)O3 with x= 0.0 – 0.1 were well formed under conditions: pH≥13, reaction time of 12hrs, reaction temperature of 180oC. Dielectric constant of PLZT is higher than PZT. The grain size of the PLZT is found to be 1–3.5 µm.

The Evaporative Decomposition of Solutions Method (Eds) for the Production of Ultrafine Y1Ba2Cu3O7 from Nitrate and Mixed Anion Precursor Solutions

1989 ◽  
Vol 169 ◽  
Author(s):  
Rollin E. Lakis ◽  
Sidney R. Butler
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Barium Carbonate ◽  
Hollow Spheres ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

AbstractY1Ba2Cu3O7 has been prepared by the evaporative decomposition of solutions method. Nitrate and mixed anion solutions were atomized and decomposed at temperatures ranging from 300°C to 950°C. The resulting materials have been characterized using x-ray powder diffraction, Thermal Gravimetric Analysis (TGA), particle size analysis, Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). The powder consists of 0.3 micron agglomerated hollow spheres with a primary particle size of 0.06 micron. TGA and x-ray diffraction indicate the presence of barium nitrate and barium carbonate due to incomplete decomposition and/or product contamination by the process environment.

SIZE-INDUCED EFFECTS IN NANOSTRUCTURED NiFe2O4

2010 ◽  
Vol 24 (30) ◽  
pp. 5973-5985
Author(s):  
M. GUNES ◽  
H. GENCER ◽  
T. IZGI ◽  
V. S. KOLAT ◽  
S. ATALAY
Keyword(s):  
Electron Microscopy ◽  
Annealing Temperature ◽  
Structural Parameters ◽  
Hydrothermal Process ◽  
Lattice Parameter ◽  
Effect Of Temperature ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

NiFe 2 O 4 nanoparticles were successfully prepared by a hydrothermal process, and the effect of temperature on them was studied. The particles were annealed at various temperatures ranging from 413 to 1473 K. Studies were carried out using powder X-ray diffraction, scanning electron microscopy, infrared spectroscopy, differential thermal analysis, thermogravimetric analysis and a vibrating sample magnetometer. The annealing temperature had a significant effect on the magnetic and structural parameters, such as the crystallite size, lattice parameter, magnetization and coercivity.

Structural and Magnetic study of Al3+ doped Ni0.75Zn0.25Fe2-xAlxO4 nanoferrites

2013 ◽  
Vol 1506 ◽  
Author(s):  
L. Wang ◽  
B. K. Rai ◽  
S. R. Mishra
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Chemical Method ◽  
X Ray Diffraction ◽  
Wet Chemical Method ◽  
X Ray ◽  
Transmission Electron ◽  
Magnetic Dilution ◽  
Wet Chemical ◽  
Structural And Magnetic Properties

AbstractNanostructured Al3+ doped Ni0.75Zn0.25Fe2-xAlxO4 (x = 0.0,0.2,0.4,0.6,0.8, and 1.0) ferrites were synthesized via wet chemical method. X-ray diffraction, transmission electron microscopy, and magnetization measurements have been used to investigate the structural and magnetic properties of spinel ferrites calcined at 950 °C .With the doping of Al3+, the particle size of Ni0.75Zn0.25Fe2-xAlxO4 first increased to 47 nm at x = 0.4 and then decreased down to 37 nm at x = 1. Saturation magnetization decreased linearly with Al3+ due to magnetic dilution. The coercive field showed an inverse dependence on the particle size of ferrites.

Sign in / Sign up

Export Citation Format

Share Document