Thermal and Electrical Conductivities of Carbon Fibers and Carbon Nanotubes Incorporated Polyurethanes Composites

2010 ◽  
Vol 442 ◽  
pp. 349-355 ◽  
Author(s):  
Shahrul A. Abdullah ◽  
Lars Frormann ◽  
Anjum Saleem
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Electrical Resistivity ◽  
Carbon Fibers ◽  
Polymer Matrix ◽  
Filler Concentration ◽  
Melt Mixing ◽  
Electrical Conductivities ◽  
The Matrix ◽  
Polyurethane Composites

Single filler polyurethane composites with carbon fibers (CFs) and multi-walled carbon nanotubes (MWNTs) were prepared by melt mixing methods and its thermal as well as electrical resistivity characteristics were investigated. The influences of fillers and mixing methods on thermal and electrical conductivity of CF/- and MWNT/polyurethane composites were investigated and the result shows that the addition of carbon fillers improved the thermal conductivity of the polyurethane composites. Higher filler concentration results in better thermal conductivity because better formation of thermally conductive networks along polymer matrix to ensure the thermal was conducted through the matrix and the network along the polymer composites. The presence of carbon additives improves the electrical resistivity of the materials as well. The present study revealed the potential of carbon as agent for better thermal and electrical conductivities and their properties depend strongly on the dispersion and distribution of the fillers in the polymer matrix.

scholarly journals Influence of Carbon Nanotubes on Polyamide Properties

2019 ◽  
Vol 33 (3) ◽  
pp. 337-346
Author(s):  
Sanja Lučić Blagojević ◽  
Nicol Šorgo ◽  
Zrinka Buhin Šturlić
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Tensile Test ◽  
Electrochemical Impedance ◽  
Test Results ◽  
Yield Strain ◽  
Scanning Calorimetry ◽  
Melt Mixing ◽  
The Matrix ◽  
Modified Carbon Nanotubes

In this study, the addition of carbon nanotubes (MWCNT) and modified carbon nanotubes (MWCNT-COOH) in the range of 0.5 wt. % to 5 wt. % in polyamide (PA) obtained as a residue upon 3D printing, was investigated. PA and nanocomposite samples were prepared by melt mixing. PA/MWCNT and PA/MWCNT-COOH nanocomposites were characterized by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), THB thermal conductivity determination method, electrochemical impedance spectroscopy (EIS), and tensile test. Results of DSC analysis showed that both types of carbon nanotubes (MWCNTs) acted as nucleation centres of PA matrix, but had no effect on the order of the crystalline structure. Due to the polar nature of the surface and better dispersion, MWCNT-COOH filler accelerated PA crystallization more significantly compared to MWCNT. Due to the presence of nanofiller, the PA chains had limited motion space, which interfered with the crystallization process of the matrix. The thermal stability of the PA matrix increased with the addition of both MWCNT and MWCNT-COOH fillers. Higher thermal conductivity was achieved with the addition of MWCNT-COOH filler compared to the addition of MWCNT. The results of the tensile test showed that with the addition of both types of MWCNT fillers in the PA matrix, the modulus of elasticity and yield stress had reduced, but the yield strain increased. Results of the EIS showed that MWCNT nanofiller had not changed the electrical conductivity regardless of modification.

scholarly journals Thermal Conductivity and Electrical Resistivity of Melt-Mixed Polypropylene Composites Containing Mixtures of Carbon-Based Fillers

Polymers ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 1073 ◽  
Author(s):  
Beate Krause ◽  
Piotr Rzeczkowski ◽  
Petra Pötschke
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Electrical Resistivity ◽  
Carbon Fibers ◽  
Filler Content ◽  
Synergistic Effects ◽  
Volume Resistivity ◽  
Graphite Nanoplatelets ◽  
Polypropylene Composites ◽  
Carbon Based

Melt-mixed composites based on polypropylene (PP) with various carbon-based fillers were investigated with regard to their thermal conductivity and electrical resistivity. The composites were filled with up to three fillers by selecting combinations of graphite nanoplatelets (GNP), carbon fibers (CF), carbon nanotubes (CNT), carbon black (CB), and graphite (G) at a constant filler content of 7.5 vol%. The thermal conductivity of PP (0.26 W/(m·K)) improved most using graphite nanoplatelets, whereas electrical resistivity was the lowest when using multiwalled CNT. Synergistic effects could be observed for different filler combinations. The PP composite, which contains a mixture of GNP, CNT, and highly structured CB, simultaneously had high thermal conductivity (0.5 W/(m·K)) and the lowest electrical volume resistivity (4 Ohm·cm).

A Study on Thermal and Electrical Conductivities of Ethylene-Butene Copolymer Composites with Carbon Fibers

2021 ◽  
Vol 36 (4) ◽  
pp. 417-422
Author(s):  
Y. Hamid ◽  
P. Svoboda
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Carbon Fiber ◽  
Electric Conductivity ◽  
Carbon Fibers ◽  
Mechanical Strain ◽  
Electric Resistance ◽  
Resistance Change ◽  
Electrical Conductivities ◽  
Fiber Sample

Abstract Ethylene-butene copolymer (EBC)/carbon-fiber (CF) composites can be utilized as an electromechanical material due to their ability to change electric resistance with mechanical strain. The electro-mechanical properties and thermal conductivity of ethylene butene copolymer (EBC) composites with carbon fibers were studied. Carbon fibers were introduced to EBC with various concentrations (5 to 25 wt%). The results showed that carbon fibers’ addition to EBC improves the electric conductivity up to 10 times. Increasing the load up to 2.9 MPa will raise the electric resistance change by 4 500% for a 25% fiber sample. It is also noted that the EBC/CF composites’ electric resistance underwent a dramatic increase in raising the strain. For example, the resistance change was around 13 times higher at 15% strain compared to 5% strain. The thermal conductivity tests showed that the addition of carbon fibers increases the thermal conductivity by 40%, from 0.19 to 0.27 Wm–1K–1.

Thermal and Electrical Conductivities of Sodium from 40 to 360 K

1972 ◽  
Vol 50 (12) ◽  
pp. 1386-1401 ◽  
Author(s):  
J. G. Cook ◽  
M. P. Van der Meer ◽  
M. J. Laubitz
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Low Temperatures ◽  
Characteristic Temperature ◽  
Published Data ◽  
Inelastic Electron ◽  
Conductivity Data ◽  
Electron Collisions ◽  
Electrical Conductivities ◽  
Flow Apparatus

We present data on the electrical and thermal resistivities and the thermopower of three pure Na specimens from 40 to 360 K. The measurements were made using a guarded longitudinal heat flow apparatus that had previously been calibrated with Au and Al. The specimens were placed in a vacuum environment using no solid inert liner.The electrical resistivity data indicate ΘR = 194 K. The thermal conductivity data show a 4% minimum near 70 K and an ice point value of 1.420 W/cm K. The reduced Lorenz function L/L0 agrees with published data at low temperatures but above 300 K levels off at approximately 0.91. On the basis of published data for liquid Na, L/L0 does not change by more than 3% at the melting point.The minimum in the thermal conductivity and a part of the high temperature deviations of L from L0 are tentatively ascribed to inelastic electron–phonon collisions having a characteristic temperature near that of longitudinal phonons. The possibility that electron–electron collisions further depress L at high temperatures is critically examined.

Composites of Carbon Filaments Made from Methane

2001 ◽  
Vol 702 ◽  
Author(s):  
Xiaoping Shui ◽  
Xuli Fu ◽  
Martin Segiet ◽  
D.D.L. Chung
Keyword(s):  
Carbon Fibers ◽  
Polymer Matrix ◽  
Electromagnetic Interference ◽  
Small Diameter ◽  
Cement Matrix ◽  
Structural Composites ◽  
Structural Functions ◽  
The Matrix ◽  
Carbon Filaments ◽  
Electromagnetic Performance

ABSTRACTPolymer-matrix and cement-matrix structural composites containing discontinuous carbon filaments (diameter = 0.1 μm) that were made catalytically from methane were developed for structural and electromagnetic functions. The composites were particularly attractive for electromagnetic interference shielding and radio wave reflection, due to the skin effect and the small diameter of the filaments. Coating the filaments with nickel by electroplating further enhanced the electromagnetic performance. However, the composites were not attractive for structural functions other than vibration damping, due to the large amount of interface between the filaments and the matrix. An effective configuration for the damping function involved using the filaments as an additive between the laminae of continuous conventional carbon fibers in a polymer-matrix structural composite.

Anisotropic thermal conductivity of polypropylene composites filled with carbon fibers and multiwall carbon nanotubes

2014 ◽  
Vol 36 (11) ◽  
pp. 1951-1957 ◽  
Author(s):  
Ilya Mazov ◽  
Igor Burmistrov ◽  
Igor Il'inykh ◽  
Andrey Stepashkin ◽  
Denis Kuznetsov ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Carbon Fibers ◽  
Multiwall Carbon Nanotubes ◽  
Polypropylene Composites ◽  
Anisotropic Thermal Conductivity ◽  
Multiwall Carbon

Thermoelectric Properties of Carbon Nanotubes Added n-type CoSb3 Compound

2011 ◽  
Vol 1314 ◽  
Author(s):  
Takashi Itoh ◽  
Masashi Tachikawa
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Electrical Resistivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Phonon Scattering ◽  
Pulse Discharge ◽  
Molar Ratios ◽  
Performance Reduction ◽  
Compound Matrix

ABSTRACTCobalt triantimonide compounds are well known as materials with good thermoelectric properties over temperature range of 550-900 K. For further improving thermoelectric performance, reduction of thermal conductivity is required. In this study, we attempted to disperse carbon nanotubes (CNTs) homogeneously into the n-type CoSb3 compound for lowering lattice thermal conductivity by the phonon scattering. Powders of Co, Ni, Sb and Te were blended with molar ratios of n-type Co0.92Ni0.08Sb2.96Te0.04 compound, and the compound was synthesized through a pulse discharge sintering (PDS) process. After coarsely grinding the synthesized compound, CNTs were mixed with the compound powder at different mass% (0, 0.01, 0.05 and 0.1 mass%). Then, the mixture was mechanically ground with a planetary ball milling equipment. The ground composite powder was compacted and sintered by PDS. Thermoelectric properties (Seebeck coefficient, electrical resistivity and thermal conductivity) of the sintered samples were measured. It was confirmed that the fibrous CNTs existed homogeneously in the compound matrix. The absolute value of Seebeck coefficient slightly decreased with increase of CNT content. The minimum thermal conductivity was obtained at addition of 0.01mass%CNT, and the electrical resistivity was a little increased with CNT content. The maximum ZT of 0.98 was achieved at 853 K in the 0.01mass%CNT-added sample.

Improving Electrical Conductivity and Thermal Properties of Polymers by the Addition of Carbon Nanotubes as Fillers

MRS Bulletin ◽  
2007 ◽  
Vol 32 (4) ◽  
pp. 348-353 ◽  
Author(s):  
Karen I. Winey ◽  
Takashi Kashiwagi ◽  
Minfang Mu
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Polymer Composites ◽  
Structure Property ◽  
Structure Property Relationships ◽  
Aspect Ratios ◽  
Polymer Properties ◽  
The Matrix ◽  
Conductivity Of Nanotubes

AbstractThe remarkable electrical and thermal conductivities of isolated carbon nanotubes have spurred worldwide interest in using nanotubes to enhance polymer properties. Electrical conductivity in nanotube/polymer composites is well described by percolation, where the presence of an interconnected nanotube network corresponds to a dramatic increase in electrical conductivity ranging from 10−5 S/cm to 1 S/cm. Given the high aspect ratios and small diameters of carbon nanotubes, percolation thresholds are often reported below 1 wt% although nanotube dispersion and alignment strongly influence this value. Increases in thermal conductivity are modest (∼3 times) because the inter facial thermal re sis tance between nanotubes is considerable and the thermal conductivity of nanotubes is only 104 greater than the polymer, which forces the matrix to contribute more toward the composite thermal conductivity, as compared to the contrast in electrical conductivity, >1014. The nanotube network is also valuable for improving flame-retardant efficiency by producing a protective nanotube residue. In this ar ticle, we highlight published research results that elucidate fundamental structure–property relationships pertaining to electrical, thermal, and/or flammability properties in numerous nanotube-containing polymer composites, so that specific applications can be targeted for future commercial success.

Sign in / Sign up

Export Citation Format

Share Document