Different Cr Contents in Nanostructured Fe-Ni-Cr Alloys Prepared by Mechanical Alloying

2012 ◽  
Vol 531-532 ◽  
pp. 437-441 ◽  
Author(s):  
Qi He ◽  
Tao Liu ◽  
Jian Liang Xie
Keyword(s):  
Particle Size ◽  
Mechanical Alloying ◽  
Ball Milling ◽  
Lattice Distortion ◽  
Milling Time ◽  
Nanocrystalline Powders ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ball Milling Time ◽  
Scanning Electron

Fe-Ni-Cr alloy powders with the different components were prepared by Mechanical Alloying (MA). The phase structure, grain size, micro-strain and lattice distortion were determined with X-ray diffraction. The morphology and particle size of the powders were observed and analyzed using a field emission scanning electron microscopy. The results showed that the Fe-Ni-Cr nanocrystalline powders could be obtained by MA. The ball milling time could be reduced with increasing amount of Cr, resulting the formation of Fe-Ni-Cr powders. With the increasing amount of Cr, the speed of Ni diffusion to Fe lattice approaching saturation became more rapid. The particle size got smaller as the ball milling went further; the extent of micro-strain and distortion of lattice intensified; the solid solubility of Ni and Cr in Fe was increased. Finally the super-saturated solid solution of Fe was obtained.

Mechanically Driven Alloying and Magnetic Properties in Immiscible Mn80Bi20 Nanocrystalline Powders

2013 ◽  
Vol 873 ◽  
pp. 217-220
Author(s):  
Min Xu ◽  
Qun Jiao Wang
Keyword(s):  
Magnetic Properties ◽  
Mechanical Alloying ◽  
Saturation Magnetization ◽  
Ball Milling ◽  
Solid Solubility ◽  
Milling Time ◽  
Early Stage ◽  
Nanocrystalline Powders ◽  
X Ray Diffraction ◽  
X Ray

The paper has described the formation of nanocrystalline Mn80Bi20powders by mechanical alloying and studied the changes of structure and magnetic properties of the powders during the process of ball milling by using X-ray diffraction and saturation magnetization σsmeasurements. The solid solubility of bismuth in manganese increases with milling time and tends to a stable value after 80h milling. The σsof Mn80Bi20increases abruptly with milling time at the early stage and begins to decrease after 15h. At the time of 15h, the σsreaches a maximum, which is about 7Am2/kg. The result shows an interesting information that the antiferromagnetic Mn and the diamagnetic Bi produce ferromagnetic Mn80Bi20in process of mechanical alloying.

The Synthesis of Cu0.81Ni0.19 Intermetallics by Mechanical Alloying

2012 ◽  
Vol 496 ◽  
pp. 379-382
Author(s):  
Rui Song Yang ◽  
Ming Tian Li ◽  
Chun Hai Liu ◽  
Xue Jun Cui ◽  
Yong Zhong Jin
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Elemental Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scherrer Equation ◽  
Scanning Electron

The Cu0.81Ni0.19 has been synthesized directly from elemental powder of nickel and copper by mechanical alloying. The alloyed Cu0.81Ni0.19 alloy powders are prepared by milling of 8h. The grain size calculated by Scherrer equation of the NiCu alloy decreased with the increasing of milling time. The end-product was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM)

Synthesis of the Mümetal Magnetic Powders by Mechanical Alloying

2011 ◽  
Vol 672 ◽  
pp. 157-160
Author(s):  
Ionel Chicinaş ◽  
Viorel Pop ◽  
Florin Popa ◽  
Virgiliu Călin Prică ◽  
Traian Florin Marinca ◽  
...  
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Mechanical Alloying ◽  
Size Distribution ◽  
Milling Time ◽  
Cast Alloy ◽  
Argon Atmosphere ◽  
X Ray Diffraction ◽  
X Ray ◽  
Rapid Formation

The formation of quaternary 76Ni17Fe5Cu2Cr (wt. %) alloy by mechanical alloying is investigated. The elemental powders of Ni, Fe, Cu and Cr where milled in argon atmosphere in a planetary ball mill for time up to 20 h. Formation of the alloy was checked by X-ray diffraction studies. It is found that the rapid formation of the alloy lead to the rapid establishment of an equilibrium between the welding and fracture process during milling, leading to a constant particle size distribution over a big range of milling time. The morphology of the powders, studied by scanning electron microscopy (SEM) confirms the rapid increase in size. The particle size distribution and the flowability of the powders are also analyzed as a function of milling time. Enhanced magnetization was found for the milled samples, compared to a cast alloy.

Study on Generation of Fine Grained Titanium Aluminide Through Ball Milling of Ti, Al and Ni-P Coated Graphite Powder

2009 ◽  
Vol 67 ◽  
pp. 45-51
Author(s):  
Rohit Kumar Gupta ◽  
Vijaya Agarwala ◽  
Sunayan Thakur ◽  
Ramesh Chandra Agarwala ◽  
Bhanu Pant
Keyword(s):  
Particle Size ◽  
Ball Milling ◽  
Titanium Aluminide ◽  
Milling Time ◽  
Stoichiometric Composition ◽  
High Energy ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Final Particle ◽  
X Ray

High energy ball milling (HEBM) had been carried out to produce submicron size titanium aluminide intermetallics (TiAl) using elemental powders of Ti and Al alongwith Ni-P coated graphite. 1% graphite powders was added to stoichiometric composition of Ti48Al and ball milling was conducted for different milling time at varying rpm. The effect of milling time and rpm on particle size has been studied. The prepared samples have been characterized using X-ray diffraction, differential scanning calorimetry (DSC) and scaning elecron microscopy (SEM). Grain size as low as 500 nm could be achieved. Formation of Ti3Al, TiAl and carbon containing intermetallic compounds had been confirmed through X-ray diffraction. Milling time and rpm of mill is found to be important factors which control the final particle size.

The synthesis of NbSi2 by mechanical alloying

1997 ◽  
Vol 12 (5) ◽  
pp. 1172-1175 ◽  
Author(s):  
Taiping Lou ◽  
Guojiang Fan ◽  
Bingzhe Ding ◽  
Zhuangqi Hu
Keyword(s):  
Solid Solution ◽  
Differential Scanning Calorimetry ◽  
Intermetallic Compound ◽  
Mechanical Alloying ◽  
Ball Milling ◽  
Temperature Rise ◽  
Milling Time ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray

The stoichiometric intermetallic compound NbSi2 has been synthesized by mechanical alloying (MA) elemental Nb and Si powders. The alloying process has been investigated by means of x-ray diffraction (XRD) and differential scanning calorimetry (DSC). It was found that the formation of the Nb2Si intermetallic compound occurs abruptly after 65 min of milling without any interruptions during the alloying process. However, short interruptions at a 5 min interval during ball milling result in a gradual reaction for the formation of the NbSi2 compound as well as a new metastable bcc structured solid solution. We conclude that the temperature rise during mechanical alloying plays an important role in initiating the abrupt reaction after an incubation milling time.

Phase transformations and microstructural evolution in nanocrystalline Fe71B23Nb6 alloy prepared by mechanical alloying

2020 ◽  
Vol 111 (4) ◽  
pp. 307-315
Author(s):  
Mahmoud Chemingui ◽  
Chahida Mnasri ◽  
Christelle Nivot ◽  
Arnaud Tricoteaux ◽  
Yannick Lorgouilloux ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Alloying ◽  
Alloy Powder ◽  
Milling Time ◽  
Milling Process ◽  
Microstructural Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Prepared Alloy ◽  
Scanning Electron

Abstract A new nanocrystalline Fe71B23Nb6 alloy powder was prepared by mechanical alloying. The phase transformation and morphological and microstructural properties of the as-prepared alloy were investigated by scanning electron microscopy, laser granulometry, and X-ray diffraction with respect to the milling time (0- 200 h). During the milling process, it was observed that the dissolution of Nb and B atoms into the Fe matrix formed solid solutions of Fe (Nb), Fe (B), Fe23B6, Fe2B, and Fe (Nb, B). Moreover, the insertion of B atoms into the Nb network generated the Nb (B) phase. Furthermore, the minimum crystallite size was measured as approximately 1 nanometer. In addition, the dislocation density gradually increased with the extension of the milling time, and the crystallization of the partially amorphous phase occurred after 200 h of milling.

Structural Evolution of the Cu-Ni Solid Solution Formed by Ball Mechanical Alloying Treatment (BMAT)

2011 ◽  
Vol 673 ◽  
pp. 279-284 ◽  
Author(s):  
Iman Farahbakhsh ◽  
Alireza Zakeri ◽  
Palavesamuthu Manikandan ◽  
Kazuyuki Hokamoto
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Structural Evolution ◽  
Mutual Diffusion ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ma Process ◽  
Scanning Electron

A nanostructured powder with uniform distribution of Ni and Cu powders was produced by means of the Ball Mechanical Alloying Treatment (BMAT). Mutual diffusion of Ni and Cu in the nanostructured layer and the microstructure of the cross section of the remaining powders were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Electron Probe Microanalyzer (EPMA). X-ray diffraction patterns revealed that increasing the milling time gives rise to decreasing crystallite size and lattice parameter during the MA process. Furthermore, scanning electron microscopy (SEM) was utilized not only for evaluating the morphology and microstructure of the remaining powder particles but also for proving this claim that during MA process, the mutual diffusion of Ni and Cu has occurred. Elemental mappings also show that the alloying process occurred in samples but obtaining the uniform shape, size and microstructure of the powder requires increase in the milling time.

Fabrication and Structural Properties of Ni50 Al50 Alloy by Mechanical Alloying

2021 ◽  
Vol 19 (7) ◽  
pp. 110-114
Author(s):  
H.M. Abdul Majeed ◽  
I.K. Jassim ◽  
A.S. Mahmood
Keyword(s):  
Particle Size ◽  
Mechanical Alloying ◽  
Ball Mill ◽  
Milled Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Compound Type ◽  
Xrd Patterns ◽  
Scanning Electron ◽  
Structure Properties

In the present study, mechanical alloying process was employed for preparation of the nanocrystalline Ni50Al50 alloy through ball mill method. The structure properties of the alloy at various milling times of 0, 2, 4, 6 and 8hr were studied by X-ray diffraction and scanning electron microscopy (SEM) measurements. Several phases was formed successfully after 4hr of milling. At 6hr of milling, new intermetallic compound type (Ni3AI) was observed prospering, The particle size for various milling times decreased significantly, with increasing time of milling. The resulted morphology the milled powder shows a reduction of particle size which is in accordance with the XRD patterns. The results of EDX shows clearly atypical spectrums of both Ni and Al peaks.

scholarly journals Mechanical properties of the Al-Mg/MWCNTs composite powders: The effects of ball milling process parameters

2021 ◽  
Author(s):  
Hossein Ahmadian
Keyword(s):  
Mechanical Properties ◽  
Ball Milling ◽  
Milling Time ◽  
Milling Process ◽  
X Ray Diffraction ◽  
Composite Powders ◽  
X Ray ◽  
Ball Milling Process ◽  
Carbon Nano Tubes ◽  
Ball Milling Time

Abstract The effects of multi-walled carbon nano-tubes (MWCNTs) and the ball milling parameters on the mechanical properties of the Al-Mg alloy powders were investigated. Three different composite powders were synthesized through ball-milling process at different time and milling rates. The microstructural and phase analyses were carried out via scanning electron microscopy and X-ray diffraction spectroscopy, respectively. The results indicated that increasing the ball-milling time and rate would lead to the formation of finer particles, which consequently intensifies the plastic deformation and then, results in lower crystallite size. The morphological investigations indicated that while the MWCNTs agglomerates in lower milling rates, increased milling rate not only improve the distribution of the MWCNTs, but also decreases the length of the nano-tubes and promotes their diffusion into Al-Mg matrix. The formation of Al-Mg intermetallic phases through the ball-milling process of the composite powders was also confirmed via microstructural investigations.

Dissolution of Al 6%wt c Mixture Using Mechanical Alloying

2019 ◽  
Vol 391 ◽  
pp. 82-87
Author(s):  
R. Dabouz ◽  
Meriem Bendoumia ◽  
Lounes Belaid ◽  
Mohamed Azzaz
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Mechanical Alloying ◽  
Solid Solubility ◽  
Milling Time ◽  
X Ray Diffraction ◽  
Processing Methods ◽  
X Ray ◽  
Scanning Electron

In the equilibrium processing methods the system Al-C does not show any solid solubility which means that carbon is not soluble in aluminum. In this work an investigation of mechanical alloying on system Al-C was presented to force the dissolution. Using different techniques such as the X-ray diffraction and scanning electron microscopy (SEM), it was proved the force of dissolution by studying the specters for different milling time and by flowing the evolution during annealing into a DSC. Furthermore, morphology of phases has been studied.

Sign in / Sign up

Export Citation Format

Share Document