Magnesium-Silicon Substituted Carbonate Hydroxyapatite (Mg-Si CHA): Factors Affecting Sintering

2016 ◽  
Vol 694 ◽  
pp. 88-93
Author(s):  
Ahmad Fauzi Mohd Noor ◽  
Harmiza Zainudin
Keyword(s):  
Mechanical Properties ◽  
Single Phase ◽  
Physical And Mechanical Properties ◽  
Major Effect ◽  
Carbonate Content ◽  
X Ray Diffraction ◽  
Factors Affecting ◽  
Complex Process ◽  
Powder Properties ◽  
Properties Of Materials

Sintering has major effect on the final properties of materials such as density, porosity and microstructure. Sintering of Mg-Si CHA in particular is a complex process since changes could occur during sintering, which include phase formation, grain size, pore size and carbonate content, and this in turn affects the mechanical properties. Improved mechanical properties of Mg-Si CHA is critical in load bearing implant applications. Poor control of thermal treatment of Mg-Si CHA during sintering would cause carbonate loss, leading to partial or total decomposition of Mg-Si CHA, subsequently would affect the physical and mechanical properties. The influence of powder properties (particle size, porosity, morphology) and sintering parameters (heating rate, firing atmosphere) on the sintered Mg-Si CHA microstructure was studied using scanning electron microscopy (SEM) characterization technique. The SEM results showed that we are able to produce sintered Mg-Si CHA without cracking of the compacted pellets, while keeping the carbonate level in the amount required (2 – 8%). X-Ray diffraction (XRD) was also performed on the sintered samples and the results indicated that a single phase Mg-Si-CHA was obtained, while Fourier transform infra-red (FTIR) spectroscopy result confirmed that as-synthesized Mg-Si CHA powder was a B-type.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

scholarly journals Features of the hydration process of the modified blended cement for fiber cement panels

2018 ◽  
Vol 170 ◽  
pp. 03030 ◽  
Author(s):  
Rustem Mukhametrakhimov ◽  
Liliya Lukmanova
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Blended Cement ◽  
Physical And Mechanical Properties ◽  
Hydration Process ◽  
Cement Matrix ◽  
X Ray Diffraction ◽  
Structure Form ◽  
Silicate Phase ◽  
X Ray

The paper studies features of the hydration process of the modified blended cement for fiber cement panels (FCP) using differential thermal analysis, X-ray diffraction analysis, electron microscopy and infrared spectroscopy. It is found that deeper hydration process in silicate phase, denser and finer crystalline structure form in fiber cement matrix based on the modified blended cement. Generalization of this result to the case of fiber cement panels makes it possible to achieve formation of a denser and homogeneous structure with increased physical and mechanical properties.

The Fabricated Collagen-Based Nano-Hydroxyapatite/β-Tricalcium Phosphate Scaffolds

2012 ◽  
Vol 506 ◽  
pp. 57-60 ◽  
Author(s):  
M. Ebrahimi ◽  
Naruporn Monmaturapoj ◽  
S. Suttapreyasri ◽  
P. Pripatnanont
Keyword(s):  
Mechanical Properties ◽  
Solid State ◽  
Calcium Phosphate ◽  
Biphasic Calcium Phosphate ◽  
Single Phase ◽  
Physical And Mechanical Properties ◽  
Total Porosity ◽  
Xrd Pattern ◽  
Collagen Coating ◽  
Dimensional Shrinkage

The biphasic calcium phosphate (BCP) concept was introduced to overcome disadvantages of single phase biomaterials. In this study, we prepared BCP from nanoHA and β-TCP that were synthesized via a solid state reaction. Three different ratios of pure BCP and collagen-based BCP scaffolds (%HA/%β-TCP; 30/70, 40/60 and 50/50) were produced using a polymeric sponge method. Physical and mechanical properties of all materials and scaffolds were investigated. XRD pattern proved the purity of each HA, β-TCP and BCP. SEM showed overall distribution of macropores (80-200 µm) with appropriate interconnected porosities. Total porosity of pure BCP (93% ± 2) was found to be higher than collagen-based BCP (85%± 3). It was observed that dimensional shrinkage of larger scaffold (39% ± 4) is lower than smaller one (42% ± 5) and scaffolds with higher HA (50%) ratio experienced greater shrinkage than those with higher β-TCP (70%) ratio (45% ±3 and 36% ±1 respectively). Mechanical properties of both groups tend to be very low and collagen coating had no influence on mechanical behavior. Further studies may improve the physical properties of these composite BCP.

CHARACTERIZATION OF HYDROXYAPATITE/TI6AL4V COMPOSITE POWDER UNDER VARIOUS SINTERING TEMPERATURE

2015 ◽  
Vol 75 (7) ◽  
Author(s):  
Amir Arifin ◽  
Abu Bakar Sulong ◽  
Norhamidi Muhamad ◽  
Junaidi Syarif
Keyword(s):  
Mechanical Properties ◽  
Composite Powder ◽  
Sintering Temperature ◽  
Physical And Mechanical Properties ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Different Temperatures ◽  
Two Phases ◽  
Work Interaction

Hydroxyapatite (HA) has been widely used in biomedical applications due to its excellent biocompatibility. However, Hydroxyapatite possesses poor mechanical properties and only tolerate limited loads for implants. Titanium is well-known materials applied in implant that has advantage in mechanical properties but poor in biocompatibility. The combination of the Titanium alloy and HA is expected to produce bio-implants with good in term of mechanical properties and biocompatabilty. In this work, interaction and mechanical properties of HA/Ti6Al4V was analyzed. The physical and mechanical properties of HA/Ti6Al4V composite powder obtained from compaction (powder metallurgy) of 60 wt.% Ti6Al4V and 40 wt.% HA and sintering at different temperatures in air were investigated in this study. Interactions of the mixed powders were investigated using X-ray diffraction. The hardness and density of the HA/Ti6Al4V composites were also measured. Based on the results of XRD analysis, the oxidation of Ti began at 700 °C. At 1000 °C, two phases were formed (i.e., TiO2 and CaTiO3). The results showed that the hardness HA/Ti6Al4V composites increased by 221.6% with increasing sintering temperature from 700oC to 1000oC. In contrast, the density of the composites decreased by 1.9% with increasing sintering temperature. 

Contribution of the hybrid component to the structure and properties of ceramics based on metastable phases Al2O3

2021 ◽  
pp. 127-136
Author(s):  
A. V. Maletsky ◽  
T. E. Konstantinova ◽  
D. R. Belichko ◽  
G. K. Volkova ◽  
V. V. Burkhovetsky
Keyword(s):  
Mechanical Properties ◽  
Yttrium Aluminum Garnet ◽  
Metastable Phase ◽  
Physical And Mechanical Properties ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Mutual Inhibition ◽  
X Ray ◽  
Tetragonal Lattice ◽  
Yttrium Aluminum

The paper presents results of the study of the effect of doping with yttrium oxide on ceramics of the composition (γ + θ) Al2O3 + nY2O3 (n = 0, 1, 2, 3 wt%), sintered at 1550°C for 2 h, from powders of the specified composition annealed at temperatures of 500 , 800, 1000°С. X-ray diffraction analysis established the formation in ceramics of yttrium aluminum garnet Y3Al5O12 (YAG) and a metastable phase of the same composition with a tetragonal lattice type in powders at temperatures above 1200°C. The effect of YAG on the physical and mechanical properties was established: high properties were demonstrated by ceramics of the composition α-Al2O3 + 2wt% Y2O3, obtained from a powder annealed at 1000°C. In addition, high physical and mechanical properties were observed in ceramics of the composition α-Al2O3 + 0wt% Y2O3, obtained from a powder annealed at 800°C. The effect of the so-called “mutual protection against crystallization” was discovered, which consists in the mutual inhibition of crystallization processes in powders of the Al2O3 – Y2O3 system.

Physical and Mechanical Properties of Bi0.5(Na0.81K0.19)0.5TiO3 Ceramic Modified by KNbO3

2019 ◽  
Vol 805 ◽  
pp. 71-75
Author(s):  
Suchittra Inthong ◽  
Chatchai Kruae-In ◽  
Wuttikrai Thanomsiang ◽  
Suppanat Kosolwattana ◽  
Denis Russell Sweatman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mixed Oxides ◽  
Perovskite Phase ◽  
Physical And Mechanical Properties ◽  
X Ray Diffraction ◽  
Solid State Reaction Technique ◽  
X Ray ◽  
Ceramic Samples ◽  
Pure Phase ◽  
Knoop Microhardness

This research reports the physical and mechanical properties of (1-x) Bi0.5(Na0.81K0.19)0.5TiO3-xKNbO3 (x=0.00-0.06) ceramics. The Modified Bi0.5(Na0.81K0.19)0.5TiO3 ceramics were synthesized by solid state reaction technique. The mixed oxides powders were calcined at 850 °C, 4 h and sintered at 1120 °C, 2 h to form pure phase perovskite and the optimum bulk density, respectively. The phase formation of the modified ceramic samples was determined by X-ray diffraction technique. All of the modified Bi0.5(Na0.81K0.19)0.5TiO3 ceramics exhibited a single perovskite phase. The bulk densities of the modified ceramic samples were 5.41±0.27-5.75±0.28 g/cm3 using the Archimedes’ method. The microstructure was revealed by the scanning electron microscope. The rectangular-like shape was found of all studied ceramics which had the grain size between 1.31±0.02-1.56±0.03 mm. The mechanical properties were studied by both Vickers and Knoop microhardness tester. The results are discussed in term of the relation among hardness properties, Young’s modulus, and fracture toughness.

Study on Characteristics of Outlast Acrylic Fiber

2012 ◽  
Vol 627 ◽  
pp. 85-89 ◽  
Author(s):  
Hai Xia Zhang ◽  
Xi Chang Zhang
Keyword(s):  
Mechanical Properties ◽  
Phase Change ◽  
Physical And Mechanical Properties ◽  
Decomposition Temperature ◽  
X Ray Diffraction ◽  
Acrylic Fiber ◽  
Change Temperature ◽  
And Performance ◽  
Cooling Velocity ◽  
Better Than

To analyze the structure and performance of Outlast acrylic fiber, the fiber structure was observed respectively by FTIR spectra, X-ray diffraction and scanning electron microscope, the normal physical and mechanical properties were measured, and the thermo-regulated performance was investigated by differential scanning calorimeter, thermal gravimeter analysis and step cooling test. The results indicate that the structure and normal physical and mechanical properties of Outlast acrylic fiber are slightly different from that of normal acrylic fiber. Both the melting peak and crystallization peak of Outlast acrylic fiber are single peaks, and the phase change temperature range is applicable and the phase change enthalpy is high. The decomposition temperature of Outlast acrylic fiber is around 311.85°C. The cooling velocity of Outlast acrylic fiber decreases exponentially with the increase in time, and the thermo-regulated ability of Outlast acrylic fiber is better than that of normal acrylic fiber.

Experiment Research of Luming Molybdenum Mine Rock Physical and Mechanical Properties

2014 ◽  
Vol 881-883 ◽  
pp. 1726-1731
Author(s):  
Ying Hua Zhang ◽  
Bo Chuan Zhao ◽  
Zhou Jing Ye ◽  
Zhi An Huang ◽  
Ming Shan Gong
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Slope Stability ◽  
Physical Simulation ◽  
Physical And Mechanical Properties ◽  
General Rule ◽  
Uniaxial Tensile ◽  
Factors Affecting ◽  
Uniaxial Tensile Strength ◽  
Weak Structure

Physical and mechanical properties of rocks are the fundamental factors affecting the slope stability, the rock physical and mechanical properties of the Luming molybdenum mine were tested and analyzed in the laboratory. The results can provide us the basic data and reference to do numerical simulation and physical simulation of slope stability. The experimental results showed that: the greater the depth of rock of Luming molybdenum mine, the greater the density becomes,so as the freeze-thaw coefficient; the rock strength complies with the general rule; uniaxial tensile strength of dried rocks is much larger than water-saturated rocks; various rocks compressive strength σ3 rose up with σ1 rising; the shear strength of the rocks containing weak structure surface is far less than the shear strength of the intact rocks.

Sign in / Sign up

Export Citation Format

Share Document