Removal of Pb2+, Cu2+, Ni2+, Cd2+ from Wastewater using Fly Ash Based Geopolymer as an Adsorbent

2018 ◽  
Vol 773 ◽  
pp. 373-378 ◽  
Author(s):  
Sujitra Onutai ◽  
Takaomi Kobayashi ◽  
Parjaree Thavorniti ◽  
Sirithan Jiemsirilers
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Heavy Metal ◽  
Fly Ash ◽  
Surface Area ◽  
Removal Efficiency ◽  
High Efficiency ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Removal Capacity

This work aims to evaluate the effectiveness of fly ash based geopolymer powder as an adsorbent for heavy metals in aqueous solution. The structure of synthesized geopolymer was found to be highly amorphous due to the dissolution of fly ash phase. Moreover, the fly ash geopolymer powder has higher surface area compares to original fly ash with specific surface area of 85.01 m²/g and 0.83 m2/g, respectively. For this reason, the geopolymer powder has much higher removal efficiency compared to the original fly ash powder. The removal efficiency was affected by contact time, geopolymer amount, heavy metal initial concentration, pH, and temperature. The four heavy metals were chosen (Pb2+, Cu2+, Ni2+, Cd2+) for adsorption test. The highest heavy metal removal capacity was obtained at pH 5. The geopolymer powder adsorbed metal cations in the order of Pb2+>Cu2+>Cd2+>Ni2+. In addition, Langmuir model is more suitable for fly ash geopolymer powder adsorption of heavy metal ions in aqueous solution than Freundlich model. The results showed that the fly ash geopolymer powder has high efficiency for removal metal which could be employed excellent alternative for wastewater treatment.

Removal of Some Heavy Metals by Electrocoagulation

2012 ◽  
Vol 468-471 ◽  
pp. 2882-2890 ◽  
Author(s):  
R. H. Al Anbari ◽  
S. M. Alfatlawi ◽  
J. H. Albaidhani
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Removal Efficiency ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Efficient Treatment ◽  
Electrolytic Cells ◽  
Removal Capacity ◽  
Metals Removal ◽  
Working Parameters

Heavy metal removal by electrocoagulation using iron electrodes material was investigated in this paper. Several working parameters, such as pH, current density and heavy metal ions concentration were studied in an attempt to achieve a higher removal capacity. A simple and efficient treatment process for removal of heavy metals is essentially necessary. The performance of continuous flow electrocoagulation system, with reactor consists of a ladder series of twelve electrolytic cells, each cell containing stainless steel cathode and iron anode. The treatment of synthetic solutions containing Zn 2+,Cu 2+,Ni 2+,Cr 3+,Cd 2+ and Co 2+ ,has been investigated. Results showed that iron is very effective as sacrificial electrode material for heavy metals removal efficiency and cost points. Also it was concluded that the chromium has lower efficient removal as compared to zinc, copper and nickel. At the same time cadmium and cobalt have minimum removal efficiency.

scholarly journals Heavy metal removal from wastewater using various adsorbents: a review

2016 ◽  
Vol 7 (4) ◽  
pp. 387-419 ◽  
Author(s):  
Renu ◽  
Madhu Agarwal ◽  
K. Singh
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Aquatic Ecosystems ◽  
Adsorption Process ◽  
Metal Removal ◽  
Low Cost ◽  
Heavy Metal Removal ◽  
Review Article ◽  
Removal Capacity ◽  
Removal Of Heavy Metals

Heavy metals are discharged into water from various industries. They can be toxic or carcinogenic in nature and can cause severe problems for humans and aquatic ecosystems. Thus, the removal of heavy metals from wastewater is a serious problem. The adsorption process is widely used for the removal of heavy metals from wastewater because of its low cost, availability and eco-friendly nature. Both commercial adsorbents and bioadsorbents are used for the removal of heavy metals from wastewater, with high removal capacity. This review article aims to compile scattered information on the different adsorbents that are used for heavy metal removal and to provide information on the commercially available and natural bioadsorbents used for removal of chromium, cadmium and copper, in particular.

A high-efficiency Fe2O3@Microalgae composite for heavy metal removal from aqueous solution

2020 ◽  
Vol 33 ◽  
pp. 101026 ◽  
Author(s):  
Li Shen ◽  
Junjun Wang ◽  
Zhanfei Li ◽  
Ling Fan ◽  
Ran Chen ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Heavy Metal ◽  
High Efficiency ◽  
Metal Removal ◽  
Heavy Metal Removal

Treatment of heavy metals by iron oxide coated and natural gravel media in Sustainable urban Drainage Systems

2013 ◽  
Vol 68 (3) ◽  
pp. 674-680 ◽  
Author(s):  
M. J. Norris ◽  
I. D. Pulford ◽  
H. Haynes ◽  
C. C. Dorea ◽  
V. R. Phoenix
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Iron Oxide ◽  
Surface Area ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Urban Drainage ◽  
Road Runoff ◽  
Drainage Systems ◽  
Urban Drainage Systems

Sustainable urban Drainage Systems (SuDS) filter drains are simple, low-cost systems utilized as a first defence to treat road runoff by employing biogeochemical processes to reduce pollutants. However, the mechanisms involved in pollution attenuation are poorly understood. This work aims to develop a better understanding of these mechanisms to facilitate improved SuDS design. Since heavy metals are a large fraction of pollution in road runoff, this study aimed to enhance heavy metal removal of filter drain gravel with an iron oxide mineral amendment to increase surface area for heavy metal scavenging. Experiments showed that amendment-coated and uncoated (control) gravel removed similar quantities of heavy metals. Moreover, when normalized to surface area, iron oxide coated gravels (IOCGs) showed poorer metal removal capacities than uncoated gravel. Inspection of the uncoated microgabbro gravel indicated that clay particulates on the surface (a natural product of weathering of this material) augmented heavy metal removal, generating metal sequestration capacities that were competitive compared with IOCGs. Furthermore, when the weathered surface was scrubbed and removed, metal removal capacities were reduced by 20%. When compared with other lithologies, adsorption of heavy metals by microgabbro was 10–70% higher, indicating that both the lithology of the gravel, and the presence of a weathered surface, considerably influence its ability to immobilize heavy metals. These results contradict previous assumptions which suggest that gravel lithology is not a significant factor in SuDS design. Based upon these results, weathered microgabbro is suggested to be an ideal lithology for use in SuDS.

Preparation and characterization of Ca-doped zinc oxide nanoparticles for heavy metal removal from aqueous solution

MRS Advances ◽  
2016 ◽  
Vol 1 (53) ◽  
pp. 3607-3612 ◽  
Author(s):  
Imed Ghiloufi ◽  
Jaber El Ghoul ◽  
Abueliz Modwi ◽  
Lassaad El Mir
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Heavy Metal ◽  
Zinc Oxide ◽  
Metal Removal ◽  
Sol Gel ◽  
Heavy Metal Removal ◽  
Nano Zinc Oxide ◽  
Calcium Doped ◽  
Nano Zinc

ABSTRACTNano zinc oxide (ZnO) and Calcium doped zinc oxide (CZ) nanopowders were synthesized by sol–gel method from zinc acetate di-hydrate and an adequate quantity of calcium chloride hexa-hydrate. Calcium doped zinc oxide (CZ) were prepared at different Ca concentrations from 1 wt% (CZ1) to 5 wt% (CZ5). The obtained nanopowders were characterized by transmission electron microscopy and X-ray diffraction. The objective of this work is to find a new and highly efficient nanomaterial for the adsorption of heavy metals from waste water. For this reason, the nanopowders were used to uptake heavy metals (Cr, Cd, and Ni) from aqueous solution. The obtained results show that the incorporation of Ca in nanoparticles zinc oxide (ZnO) increases the capacity adsorption of nanopowders and CZ3 is more efficient than the other Ca-doped samples. In this work we studied also the effect of pH and the pyrolysis temperature of the nanopowders on the removal of heavy metal ions from aqueous solution by CZ3.

scholarly journals Heavy metal removal from MSS fly ash by thermal and chlorination treatments

2015 ◽  
Vol 5 (1) ◽  
Author(s):  
Jingyong Liu ◽  
Jiacong Chen ◽  
Limao Huang
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Fly Ash ◽  
Evaporation Rate ◽  
Metal Removal ◽  
Removal Rate ◽  
Heavy Metal Removal ◽  
Efficient Removal ◽  
Waste Sludge ◽  
Cu And Zn

Abstract The thermal behavior of heavy metals in the co-incineration of municipal solid waste-sludge incinerator fly ash (MSS fly ash) was studied using a laboratory-scale tube furnace. The results indicate that without the addition of chlorinating agents, temperature was an important parameter and had significantly influenced on heavy metal removal, whereas the residence time had a weak effect. Between 900 and 1000 °C for 60 to 300 min, heavy metals reacted with chloride-inherent in the fly ash and approximately 80 to 89% of Pb, 48% to 56% of Cd, 27% to 36% of Zn and 6% to 24% of Cu were removed. After the adding chlorinating agents, the evaporation rate of the heavy metals improved dramatically, where the evaporation rates of Cu and Zn were larger than that of Pb and Cd. As the amount of added chlorinating agents increased, the removal rate of heavy metals increased. However, the effect of the type of chlorinating agent on the chlorination of heavy metals differed considerably, where NaCl had the weakest effect on the removal rate of Cu, Cd and Zn. In terms of resource recovery and decontamination, MgCl2 and CaCl2 are the best choices due to their efficient removal of Zn.

scholarly journals Use of Natural Zeolites as a Detoxifier of Heavy Metals in Water and the Flesh of Reared European Seabass Dicentrarchus labrax

2020 ◽  
Vol 78 (3) ◽  
pp. 121-132
Author(s):  
Hadir A. Aly ◽  
Mohamed M. Abdel-Rahim ◽  
Ghada R. Sallam ◽  
Ayman M. Lotfy ◽  
Basem S. Abdelaty
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Body Weight ◽  
Removal Efficiency ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Dicentrarchus Labrax ◽  
Feed Utilization ◽  
Natural Zeolites ◽  
Fish Flesh

AbstractA study was conducted to investigate the effects of natural zeolites as a water clarifier on the heavy metal removal efficiency from the underground saltwater used for rearing Dicentrarchus labrax fry. Five concentrations of zeolites were tested: 0 (Z0), 2.5‰ (Z2.5), 5‰ (Z5), 7.5‰ (Z7.5) and 10‰ (Z10). Fry with an initial body weight of 1.53±0.018 g/fish were stocked in 15 aquaria at a density of 10 fry/aquarium. The fish were fed a commercial diet (42% protein and 12.34% lipid) twice daily (09:30 and 14:00) at 5% of their body weight per day for 42 days. Growth, feed utilization, survival and heavy metal removal efficiency were evaluated. The growth performance and feed utilization indices gradually improved with increasing zeolite concentration, with the most significant (P≤0.05) values detected at Z10. The survival rate decreased significantly at Z10 compared with the control (Z0). Increasing the zeolite concentration significantly (P≤0.05) improved the removal efficiency of heavy metals in the rearing water with adsorption selectivity of Pb˃Cd˃Fe˃Cu˃Zn. Furthermore, an increase in the detoxification rate of heavy metals in fish flesh with increasing zeolite level was detected with the removal selectivity of Fe˃Cu˃Zn˃Pb˃Cd. In conclusion, it can be stated that natural zeolites can be used effectively to reduce heavy metals in polluted waters and subsequently in fish flesh in addition to improving fish performance.

Heavy metal removal from wastewater using zero-valent iron nanoparticles

2008 ◽  
Vol 58 (10) ◽  
pp. 1947-1954 ◽  
Author(s):  
S. Y. Chen ◽  
W. H. Chen ◽  
C. J. Shih
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Removal Efficiency ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Zero Valent Iron ◽  
Affecting Factors ◽  
High Concentration ◽  
Initial Ph ◽  
Low Efficiency

Because of having a high reduction potential, the zero-valent iron (ZVI) is often applied for the remediation of wastewater or groundwater with heavy metals. The purpose of this study was aimed to investigate the reaction behavior of heavy metals with ZVI nanoparticles in the wastewater. The affecting factors, such as initial pH, dosage of nanoscale ZVI and initial concentration of heavy metal, on the removal efficiency of heavy metals by ZVI in the wastewater were examined by the batch experiments in this study. It was found that the removal of heavy metals was affected by initial pH. The rate and efficiency of metal removal increased with decreasing initial pH. Greater than 90% of the heavy metals were removed when the initial pH was controlled at 2. In addition, the rate and efficiency of metal removal increased as the dosage of nanoscale ZVI increased. The removal efficiency of heavy metal was higher than 80% when 2.0 g/L of ZVI was added in the wastewater. On the other hand, the slow rate and low efficiency of metal removal from the wastewater treated by nanoscale ZVI was found in the wastewater with high concentration of heavy metal.

Electrokinetic Remediation of Heavy Metal Contaminated Soil Using Permeable Reactive Composite Electrodes

2012 ◽  
Vol 518-523 ◽  
pp. 361-368 ◽  
Author(s):  
Rong Bing Fu ◽  
Xin Xing Liu ◽  
Fang Liu ◽  
Jin Ma ◽  
Yu Mei Ma ◽  
...  
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Removal Efficiency ◽  
Heavy Metal Ions ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Ph Control ◽  
Electrokinetic Remediation ◽  
Composite Electrodes ◽  
Remediation Process

A new permeable reactive composite electrode (PRCE) attached with a permeable reactive layer (PRL) of Fe0 and zeolite has been developed for soil pH control and the improved removal efficiency of heavy metal ions (Cd, Ni, Pb, Cu) from soil in electrokinetic remediation process. The effects of different composite electrodes on pH control and heavy metal removal efficiency were studied, and changes in the forms of heavy metals moved onto the electrodes were analyzed. The results showed that with acidic/alkaline zeolite added and renewed in time, the composite electrodes could effectively neutralize and capture H+ and OH- produced from electrolysis of the anolyte and catholyte, avoiding or delaying the formation of acidic/alkaline front in tested soil, preventing premature precipitation of heavy metal ions and over-acidification of soil, and thus significantly improved the heavy metal removal efficiency. Fe0 in composite electrodes could deoxidize and stabilize the heavy metal ions. After that capture and immobilization of the pollutants were achieved. The results also showed that, using "Fe0 + zeolite" PRCE in the cathode with timely renewal, after 15-day remediation with a DC voltage of 1.5 V/cm, the total removal rates of Cd, Pb, Cu and Ni were 49.4%, 47.1%, 36.7% and 39.2%, respectively.

Sign in / Sign up

Export Citation Format

Share Document