Electron and Laser Beam Additive Manufacturing with Wire - Comparison of Processes

2019 ◽  
Vol 799 ◽  
pp. 294-299 ◽  
Author(s):  
Marek Stanisław Węglowski ◽  
Sylwester Błacha ◽  
Robert Jachym ◽  
Jan Dutkiewicz ◽  
Łukasz Rogal ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stainless Steel ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Laser Beam ◽  
Cross Section ◽  
Mechanical Tests ◽  
Manufacturing Processes ◽  
Metallographic Examination

Electron beam (EBAM) and laser beam (LBAM) additive manufacturing processes with a deposited material in the form of a wire are an efficient methods enabling the making of component parts. The scope of the presented work was to investigate the influence of technological process on microstructure and mechanical properties such as tensile strength, microhardness and elongation of the fabricated components. The achieved results and gained knowledge will enable the production of a whole structure from stainless steel in the future. The metallographic examination revealed that the microstructure is not fully homogenies, the cell-dendritic areas occurred. Moreover, the microhardness profiles indicated that some fluctuation in the microstructure as well as mechanical properties can be observed on the cross section of deposited components. However, the mechanical tests showed that the tensile strength as well as elongation fulfil the requirement of producer of deposited wire.

scholarly journals Directionally-Dependent Mechanical Properties of Ti6Al4V Manufactured by Electron Beam Melting (EBM) and Selective Laser Melting (SLM)

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3603
Author(s):  
Tim Pasang ◽  
Benny Tavlovich ◽  
Omry Yannay ◽  
Ben Jakson ◽  
Mike Fry ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Tensile Strength ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Selective Laser Melting ◽  
Electron Beam Melting ◽  
Rolling Direction ◽  
Laser Melting ◽  
Plate Rolling

An investigation of mechanical properties of Ti6Al4V produced by additive manufacturing (AM) in the as-printed condition have been conducted and compared with wrought alloys. The AM samples were built by Selective Laser Melting (SLM) and Electron Beam Melting (EBM) in 0°, 45° and 90°—relative to horizontal direction. Similarly, the wrought samples were also cut and tested in the same directions relative to the plate rolling direction. The microstructures of the samples were significantly different on all samples. α′ martensite was observed on the SLM, acicular α on EBM and combination of both on the wrought alloy. EBM samples had higher surface roughness (Ra) compared with both SLM and wrought alloy. SLM samples were comparatively harder than wrought alloy and EBM. Tensile strength of the wrought alloy was higher in all directions except for 45°, where SLM samples showed higher strength than both EBM and wrought alloy on that direction. The ductility of the wrought alloy was consistently higher than both SLM and EBM indicated by clear necking feature on the wrought alloy samples. Dimples were observed on all fracture surfaces.

Mechanical Testing of Additive Manufactured Metal Parts

2015 ◽  
Vol 651-653 ◽  
pp. 713-718 ◽  
Author(s):  
Marion Merklein ◽  
Raoul Plettke ◽  
Daniel Junker ◽  
Adam Schaub ◽  
Bhrigu Ahuja
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Stainless Steel ◽  
Additive Manufacturing ◽  
Laser Beam ◽  
Round Robin Test ◽  
Metal Parts ◽  
Laser Beam Melting ◽  
Made In

The quality of additive manufactured parts however depends pretty much on the workers experience to control porosity, layer linkage and surface roughness. To analyze the robustness of the Laser Beam Melting (LBM) process a Round Robin test was made in which specimens from four institutes from different countries were tested and compared. For the tests each institute built a set of specimens out of stainless steel 1.4540. The aim of this work is to analyze the influence of the process parameters on the mechanical properties. The results show that there is a high potential for additive manufacturing but also a lot of further research is necessary to optimize this technology.

Structural Optimization and Additive Manufacturing

2014 ◽  
Vol 611-612 ◽  
pp. 811-817 ◽  
Author(s):  
Julen Ibabe ◽  
Antero Jokinen ◽  
Jari Larkiola ◽  
Gurutze Arruabarrena
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Stainless Steel ◽  
Additive Manufacturing ◽  
Structural Optimization ◽  
Finite Element Simulations ◽  
Optimization Process ◽  
Manufacturing Processes ◽  
Complex Geometries ◽  
Additive Manufacturing Technology

Additive Manufacturing technology offers almost unlimited capacity when manufacturing parts with complex geometries which could be impossible to get with conventional manufacturing processes. This paper is based on the study of a particular real part which has been redesigned and manufactured using an AM process. The challenge consists of redesigning the geometry of an originally aluminium made part, in order to get a new stainless steel made model with same mechanical properties but with less weight. The new design is the result of a structural optimization process based on Finite Element simulations which is carried out bearing in mind the facilities that an AM process offers.

Reinforcing Inconel 718 Superalloy by Nano-TiC Particles in Selective Laser Melting

2015 ◽  
Author(s):  
Yachao Wang ◽  
Jing Shi ◽  
Yun Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Ultimate Tensile Strength ◽  
Yield Stress ◽  
Selective Laser Melting ◽  
Inconel 718 ◽  
Reinforcement Particle ◽  
Manufacturing Processes ◽  
Laser Melting

Metal components produced by additive manufacturing processes usually have inferior properties and performances as compared with the counterparts by the traditional forming and machining processes. To close the gap, the metal matrix can be strengthened by adding reinforcement particles in additive manufacturing processes. This research presents the fabrication of nano-TiC reinforced Inconel 718 composites using selective laser melting (SLM). Tensile and wear performance tests are conducted to evaluate the mechanical properties of the formed composites. It is discovered that the composites exhibit improved mechanical properties in terms of ultimate tensile strength and yield stress. Compared with the pure Inconel 718 specimens by SLM, the ultimate tensile strength and yield stress of the reinforced Inconel 718 increase by 207 MPa and 204 MPa, respectively, with 0.5 wt.% addition of nano-TiC particle. Smaller increases are observed with 0.25 wt.% and 1.0 wt.% nano-TiC additions. On the other hand, the addition of nano-TiC particles decreases the ductility of Inconel 718. To investigate the strengthening mechanism of nano reinforcement particles in SLM, the microstructures with different levels of nano-TiC particles are observed. The results indicate that the microstructure of Inconel 718 is remarkably refined by the TiC particles, and the reinforcement particle significantly impede the growth of columnar grain in the solidification process.

scholarly journals Heat Input Effect on Microstructure and Mechanical Properties of Electron Beam Additive Manufactured (EBAM) Cu-7.5wt.%Al Bronze

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6948
Author(s):  
Andrey Filippov ◽  
Nikolay Shamarin ◽  
Evgeny Moskvichev ◽  
Nikolai Savchenko ◽  
Evgeny Kolubaev ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stainless Steel ◽  
Electron Beam ◽  
Heat Input ◽  
Stainless Steel Substrate ◽  
Tensile Axis ◽  
Steel Substrate ◽  
Equiaxed Grains ◽  
Wire Feed

Electron beam additive wire-feed deposition of Cu-7.5wt.%Al bronze on a stainless-steel substrate has been carried out at heat input levels 0.21, 0.255, and 0.3 kJ/mm. The microstructures formed at 0.21 kJ/mm were characterized by the presence of both zigzagged columnar and small equiaxed grains with 10% of Σ3 annealing twin grain boundaries. No equiaxed grains were found in samples obtained at 0.255 and 0.3 kJ/mm. The zigzagged columnar ones were only retained in samples obtained at 0.255 kJ/mm. The fraction of Σ3 boundaries reduced at higher heat input values to 7 and 4%, respectively. The maximum tensile strength was achieved on samples obtained with 0.21 kJ/mm as tested with a tensile axis perpendicular to the deposited wall’s height. More than 100% elongation-to-fracture was achieved when testing the samples obtained at 0.3 kJ/mm (as tested with a tensile axis coinciding with the wall’s height).

scholarly journals Comparison between Mechanical Properties and Structures of a Rolled and a 3D-Printed Stainless Steel

Materials ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 3867 ◽  
Author(s):  
Stefano Natali ◽  
Andrea Brotzu ◽  
Daniela Pilone
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stainless Steel ◽  
Additive Manufacturing ◽  
High Strength ◽  
Thin Sheets ◽  
Laser Melting ◽  
3D Printed ◽  
Lower Elongation ◽  
Manufacturing Technologies

In this work selective laser melting was successfully utilized to produce 316 stainless steel bulk specimens. Although this technology provides many advantages compared to conventional shaping processes, little residual porosity may be a problem for some applications where high strength is required. The objective of this work was to determine, through data analysis, a mechanical and metallographic comparison between thin sheets made by using different manufacturing technologies: Cold rolling and additive manufacturing. This comparison was useful to understand whether it could be more advantageous to use the prototyping for new mechanical components. The results show that the additive manufactured steel, due to its microstructure, is characterized by a higher yield strength and by a lower elongation and ultimate tensile strength.

Effect of silver nitrate on some mechanical properties of heat polymerizing acrylic resins

2019 ◽  
Vol 14 (1) ◽  
pp. 110
Author(s):  
Assiss. Prof. Dr. Sabiha Mahdi Mahdi ◽  
Dr. Firas Abd K. Abd K.
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Silver Nitrate ◽  
Surface Hardness ◽  
Mechanical Tests ◽  
Hardness Tester ◽  
Acrylic Resins ◽  
The Difference

Aim: The aimed study was to evaluate the influence of silver nitrate on surfacehardness and tensile strength of acrylic resins.Materials and methods: A total of 60 specimens were made from heat polymerizingresins. Two mechanical tests were utilized (surface hardness and tensile strength)and 4 experimental groups according to the concentration of silver nitrate used.The specimens without the use of silver nitrate were considered as control. Fortensile strength, all specimens were subjected to force till fracture. For surfacehardness, the specimens were tested via a durometer hardness tester. Allspecimens data were analyzed via ANOVA and Tukey tests.Results: The addition of silver nitrate to acrylic resins reduced significantly thetensile strength. Statistically, highly significant differences were found among allgroups (P≤0.001). Also, the difference between control and experimental groupswas highly significant (P≤0.001). For surface hardness, the silver nitrate improvedthe surface hardness of acrylics. Highly significant differences were statisticallyobserved between control and 900 ppm group (P≤0.001); and among all groups(P≤0.001)with exception that no significant differences between control and150ppm; and between 150ppm and 900ppm groups(P>0.05).Conclusion: The addition of silver nitrate to acrylics reduced significantly the tensilestrength and improved slightly the surface hardness.

scholarly journals The Structure and Mechanical Properties of Hemp Fibers-Reinforced Poly(ε-Caprolactone) Composites Modified by Electron Beam Irradiation

2021 ◽  
Vol 11 (12) ◽  
pp. 5317
Author(s):  
Rafał Malinowski ◽  
Aneta Raszkowska-Kaczor ◽  
Krzysztof Moraczewski ◽  
Wojciech Głuszewski ◽  
Volodymyr Krasinskyi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
High Energy ◽  
Electron Radiation ◽  
Elongation At Break ◽  
Hemp Fibers

The need for the development of new biodegradable materials and modification of the properties the current ones possess has essentially increased in recent years. The aim of this study was the comparison of changes occurring in poly(ε-caprolactone) (PCL) due to its modification by high-energy electron beam derived from a linear electron accelerator, as well as the addition of natural fibers in the form of cut hemp fibers. Changes to the fibers structure in the obtained composites and the geometrical surface structure of sample fractures with the use of scanning electron microscopy were investigated. Moreover, the mechanical properties were examined, including tensile strength, elongation at break, flexural modulus and impact strength of the modified PCL. It was found that PCL, modified with hemp fibers and/or electron radiation, exhibited enhanced flexural modulus but the elongation at break and impact strength decreased. Depending on the electron radiation dose and the hemp fibers content, tensile strength decreased or increased. It was also found that hemp fibers caused greater changes to the mechanical properties of PCL than electron radiation. The prepared composites exhibited uniform distribution of the dispersed phase in the polymer matrix and adequate adhesion at the interface between the two components.

Sign in / Sign up

Export Citation Format

Share Document