scholarly journals The Structure and Mechanical Properties of Hemp Fibers-Reinforced Poly(ε-Caprolactone) Composites Modified by Electron Beam Irradiation

2021 ◽  
Vol 11 (12) ◽  
pp. 5317
Author(s):  
Rafał Malinowski ◽  
Aneta Raszkowska-Kaczor ◽  
Krzysztof Moraczewski ◽  
Wojciech Głuszewski ◽  
Volodymyr Krasinskyi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
High Energy ◽  
Electron Radiation ◽  
Elongation At Break ◽  
Hemp Fibers

The need for the development of new biodegradable materials and modification of the properties the current ones possess has essentially increased in recent years. The aim of this study was the comparison of changes occurring in poly(ε-caprolactone) (PCL) due to its modification by high-energy electron beam derived from a linear electron accelerator, as well as the addition of natural fibers in the form of cut hemp fibers. Changes to the fibers structure in the obtained composites and the geometrical surface structure of sample fractures with the use of scanning electron microscopy were investigated. Moreover, the mechanical properties were examined, including tensile strength, elongation at break, flexural modulus and impact strength of the modified PCL. It was found that PCL, modified with hemp fibers and/or electron radiation, exhibited enhanced flexural modulus but the elongation at break and impact strength decreased. Depending on the electron radiation dose and the hemp fibers content, tensile strength decreased or increased. It was also found that hemp fibers caused greater changes to the mechanical properties of PCL than electron radiation. The prepared composites exhibited uniform distribution of the dispersed phase in the polymer matrix and adequate adhesion at the interface between the two components.

scholarly journals Effect of Gamma Radiation on the Mechanical Properties of Natural Fabric Reinforced Polyester Composites

2019 ◽  
Vol 27 (4(136)) ◽  
pp. 88-93
Author(s):  
K.Z.M. Abdul Motaleb ◽  
Md Shariful Islam ◽  
Rimvydas Milašius
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Gamma Radiation ◽  
Bending Strength ◽  
Polyester Resin ◽  
Radiation Doses ◽  
Elongation At Break ◽  
Bending Modulus ◽  
Polyester Composites

Two types of composites:(1) pineapple fabric reinforced polyester resin (Pineapple/PR) and (2) jute fabric reinforced polyester resin (Jute/PR) were prepared and the mechanical properties investigated for various gamma radiation doses ranging from 100-500 krad. Properties like tensile strength, Young’s modulus, elongation-at-break, bending strength, bending modulus and impact strength were increased significantly by 19%, 32%, 45%, 32%, 47% and 20%, respectively, at a dose of 300 krad for Pineapple/PR, and by 47%, 49%, 42%, 45%, 52% and 65%, respectively, at a dose of 200 krad for the Jute/PR composite in comparison to the non-irradiated composite. Gamma radiation improved the mechanical properties, but overdoses of radiation even caused a reduction in them.

Comparison of Melt Flow and Mechanical Properties of Rice Husk and Kenaf Hybrid Composites

2013 ◽  
Vol 701 ◽  
pp. 42-46 ◽  
Author(s):  
Abd Aziz Noor Zuhaira ◽  
Rahmah Mohamed
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Rice Husk ◽  
Hybrid Composites ◽  
Natural Fibers ◽  
Melt Flow Index ◽  
Silica Content ◽  
Flow Index ◽  
Melt Flow

This research is to identify the difference in melt flow and mechanical properties in hybrid composites between kenaf and rice husk that each of the filler was compounded with composite material of calcium carbonate (CaCO3) and high density polyethylene (HDPE) in different loading amount. Different filler loading up to 30 parts of kenaf fibers and rice husk particulate were mixed with the fixed 30% amount of CaCO3. Compounded hybrid composite were prepared and tested for melt flow index, tensile and impact strength. Addition of both fillers had decreased melt flow index (MFI). MFI of rice husk/CaCO3 was higher than kenaf/CaCO3 in HDPE composites. Tensile strength, elongation at break and impact properties of both hybrid composites had decreased with increasing filler content. Tensile strength of kenaf/CaCO3 was higher than rice husk/CaCO3 due to intrinsic fiber structure of kenaf which has some reinforcing effect compared to rice husk. While, impact strength of rice husk/CaCO3 was improved with addition of filler but drastically decrease as the rice husk content were increased up to 30% due to high silica content in rice husk. The Youngs Modulus was increased with addition of natural fibers in CaCO3/HDPE composite.

Influence of Novel Electron Beam Modified Surface Treated Dual Phase Filler on Rheometric and Mechanical Properties of Styrene Butadiene Rubber Vulcanizates

2003 ◽  
Vol 76 (2) ◽  
pp. 299-317 ◽  
Author(s):  
A. M. Shanmugharaj ◽  
Anil K. Bhowmick
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Styrene Butadiene Rubber ◽  
Dual Phase ◽  
Butadiene Rubber ◽  
Elongation At Break ◽  
Polymer Filler ◽  
Modified Surface ◽  
Styrene Butadiene

Abstract Rheometric and mechanical properties, hysteresis and swelling behavior of the Styrene-Butadiene Rubber vulcanizates (SBR) filled with unmodified and novel electron beam modified surface treated dual phase fillers were investigated. Scorch time increases for these modified filler loaded vulcanizates due to introduction of quinone type oxygen on the surface. Electron beam modification of dual phase filler in the absence of trimethylol propanetriacrylate (TMPTA) or triethoxysilylpropyltetrasulphide (Si-69) significantly improves the modulus of the SBR vulcanizates, whereas the values of tensile strength and elongation at break drop. However, presence of TMPTA or silane slightly increases the modulus with significant improvement in tensile strength. This effect is more pronounced at higher loading of these modified fillers in SBR vulcanizates. These variations in modulus and tensile strength are explained by the equilibrium swelling data, Kraus plot and a new mathematical model interpreting the polymer-filler interaction. Hysteresis loss ratio of SBR vulcanizates loaded with irradiated fillers in absence and presence of TMPTA or silane increases due to highly aggregated structure of the filler.

Effects of the Size of Wood Flour on Mechanical Properties of Wood-Plastic Composites

2011 ◽  
Vol 393-395 ◽  
pp. 76-79 ◽  
Author(s):  
Hai Bing Huang ◽  
Hu Hu Du ◽  
Wei Hong Wang ◽  
Hai Gang Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Wood Flour ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Inorganic Filler ◽  
Full Potential ◽  
Wood Plastic Composites ◽  
Plastic Composites

In this article, wood-plastic composites(WPCs) were manufactured with wood flour(80～120mesh、40～80mesh、20～40mesh、10～20mesh) combing with high density polyethylene(HDPE). Effects of the size of wood flour on mechanical properies and density of composites were investigated. Results showed that particle size of wood flour had an important effect on properitiesof WPCs. Change of mesh number had a outstanding effect on flexural modulus, tensile modulus and impact strength, howere, little effect on flexural strength and tensile strength. When mesh number of wood flour changed from 80～120mesh to 10～20mesh,flexural modulus and tensile modulus were respectively enhanced by 42.4% and 28.4%, respectively, and impact strength was decreased by 35.5%.Size of wood flour basically had no effect on density of composite within 10～120mesh. The use of wood flour or fiber as fillers and reinforcements in thermoplastics has been gaining acceptance in commodity plastics applications in the past few years. WPCs are currently experiencing a dramatic increase in use. Most of them are used to produce window/door profiles,decking,railing,ang siding. Wood thermoplastic composites are manufactured by dispering wood fiber or wood flour(WF) into molten plastics to form composite materials by processing techniques such as extrusion,themoforming, and compression or injection molding[1]. WPCs have such advantages[2]：(1)With wood as filler can improve heat resistance and strength of plastic, and wood has a low cost, comparing with inorganic filler, wood has a low density. Wood as strengthen material has a great potential in improving tensile strength and flexural modulus[3]；(2) For composite of same volume, composites with wood as filler have a little abrasion for equipment and can be regenerated；(3)They have a low water absorption and low hygroscopic property, They are not in need of protective waterproof paint, at the same time, composite can be dyed and painted for them own needs；(4)They are superior to wood in resistantnce to crack、leaf mold and termite aspects, composites are the same biodegradation as wood；(5)They can be processed or connected like wood；（6）They can be processed into a lots of complicated shape product by means of extrusion or molding and so on, meanwhile, they have high-efficiency raw material conversion and itself recycle utilization[4]. While there are many sucesses to report in WPCs, there are still some issues that need to be addressed before this technology will reach its full potential. This technology involves two different types of materials: one hygroscopic(biomass) and one hydrophobic(plastic), so there are issues of phase separation and compatibilization[5]. In this paper, Effects of the size of wood powder on mechanical properties of WPCs were studied.

Mechanical and Morphological Behavior of Blends Obtained from Biopolymers (PLA/PLC)

2014 ◽  
Vol 775-776 ◽  
pp. 24-28
Author(s):  
Taciana Regina de Gouveia Silva ◽  
Bartira Brandão da Cunha ◽  
Pankaj Agrawal ◽  
Edcleide Maria Araújo ◽  
Tomás Jefférson Alves de Mélo
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Elastic Modulus ◽  
Impact Strength ◽  
Polymer Blends ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Morphology Analysis ◽  
Morphological Behavior

In this work, the effect of the PCL content and E-GMA compatibilizer on the mechanical properties and morphology of poly (lactic acid) - PLA/ poly (ε-caprolactone)-PCL blends was investigated. The results of the mechanical properties showed that there was a reduction in the elastic modulus and tensile strength when PCL was added to PLA. The decrease in the modulus was more pronounced when the PCL content was increased from 10 to 20% (wt). The PLA/PCL/E-GMA blend showed the lower modulus and tensile strength. This blend also presented the higher elongation at break and impact strength. The morphology analysis by SEM showed that the PLA/PCL blends where characterized by lack of adhesion between the PLA and PCL phases. The presence of E-GMA in the PLA/PCL/E-GMA blend improved the adhesion between the PLA and PCL phases.Keywords: poly (latic acid); poly (ε-caprolactone); polymer blends; compatibilizer

scholarly journals Simultaneous Improvement in the Tensile and Impact Strength of Polypropylene Reinforced by Graphene

2020 ◽  
Vol 2020 ◽  
pp. 1-5
Author(s):  
Li Juan
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Fracture Surface ◽  
Impact Strength ◽  
Melt Blending ◽  
Elongation At Break ◽  
Morphological Behavior ◽  
Scanning Electron

The nanocomposites of polypropylene (PP)/graphene were prepared by melt blending. The effects of the dosage of graphene on the flow and mechanical properties of the nanocomposites were investigated. The morphologies of fracture surfaces were characterized through scanning electron microscopy (SEM). The graphene simultaneous enhanced tensile and impact properties of nanocomposites. A 3.22% increase in tensile strength, 39.8% increase in elongation at break, and 26.7% increase in impact strength are achieved by addition of only 1 wt.% of graphene loading. The morphological behavior indicates the fracture surface of PP/graphene is more rough than that of pure PP.

The Effects of a Compatibilizer for Improving Mechanical Properties on Polymer Matrix Composites

2021 ◽  
Vol 877 ◽  
pp. 3-8
Author(s):  
Prathumrat Nuyang ◽  
Atiwat Wiriya-Amornchai ◽  
Watthanaphon Cheewawuttipong
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Young’S Modulus ◽  
Polymer Matrix ◽  
Polymer Matrix Composites ◽  
Fine Powder ◽  
Matrix Composites ◽  
Elongation At Break ◽  
The Impact

The effect of compatibilizer agent was studied when adding Aluminum fine powder (Al) to reinforce in Polypropylene (PP) by compared between polymer matrix composites (PMCs) and PMCs added Polypropylene graft maleic anhydride (PP-g-MAH).The average particle size of the aluminum fine powder was around 75 μm filled in polypropylene with different proportions of 2.5, 5, 7.5 and 10wt%. PMCs were prepared using the internal mixer. The results found that when the amount of aluminum fine powder increased, the mechanical properties had changed, i.e., tensile strength, and Young’s Modulus increased, while the impact strength and elongation at break decreased. But, when adding compatibilizer 1wt% it was found that the trend of tensile strength, and Young’s Modulus increased that compared with non-compatibilizer, but the impact strength and elongation at break decreased. The part of the morphology of PMCs with non-compatibilizer was found that the particle of aluminum fine powder dispersed in the matrix phase, but there were many microvoids between filler and matrix. But, PMCs with compatibilizer caused the microvoids between filler and matrix to be reduced.

Direct Reactive Compatibilization of GMA on PE/Wood-Flour Composite

2011 ◽  
Vol 378-379 ◽  
pp. 735-739
Author(s):  
Yue Wen Li ◽  
Xin Hua Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Wood Flour ◽  
Reactive Extrusion ◽  
Rupture Surface ◽  
Elongation At Break ◽  
Reactive Compatibilization ◽  
Anchoring Strength

Reactive compatibilization between high-density polyethylene(HDPE) and wood-flour was achieved via direct reactive extrusion of glycidyl methacrylate(GMA), initiator, HDPE and wood-flour. Impact rupture surface of the composite was observed by scanning electron microscope(SEM), and its load deformation temperature(HDT) and mechanical properties were tested. Effect of GMA dosage and extrusion temperature on reactive compatibilization of the composite was analysed. The result indicated that the anchoring strength of interface in the composite was obviously strengthened, and its HDT, tensile strength, flexural strength, notched impact strength and elongation at break of the composite were distinctly improved due to the addition of GMA and dicumyl peroxide(DCP). When the composite was extruded at 180°C, the peak values of its HDT, tensile strength, flexural strength, elongation at break and notched impact strength respectively were 84°C, 40Mpa, 45Mpa, 11% and 6.6KJ.m-2, which respectively increased by 17°C, 74%, 36%, 83% and 69% than that of the composite without reactive compatibilization, and when the composite was extruded at 190°C, the peak values of its HDT, tensile strength, flexural strength, elongation at break and notched impact strength respectively were 84°C, 40Mpa, 44Mpa, 11% and 6.6KJ.m-2, which respectively increased by 20°C, 60%, 26%, 83% and 83% than that of the composite without reactive compatibilization. When GMA usage increased, the HDT and mechanical properties of the composite increased first, then descended, and the optimum usage of GMA was 1wt%-3wt%.

Effect of Polyethylene Glycol (PEG) on Molten Plasticized Cellulose Acetate (CA)

2013 ◽  
Vol 830 ◽  
pp. 172-175
Author(s):  
Cheng Zhi Chuai ◽  
Zhi Zhang
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Tensile Strength ◽  
Polyethylene Glycol ◽  
Flexural Strength ◽  
Cellulose Acetate ◽  
Flexural Modulus ◽  
Degree Of Polymerization ◽  
Maximum Elongation ◽  
Elongation At Break

Ethylene glycol (EG) and polyethylene glycol (PEG) were added as plasticizers to improve the processing performance of cellulose acetate (CA). The CA with 30% plasticizers were melted by HAAKE at 200 °C. The effects of EG and PEG (degree of polymerization in 200-800) on rheological properties and mechanical properties of CA were investigated. The results show that the plasticizing time, equilibrium torque and melt viscosity of the plasticizing system increase with the increase of PEG molecular weight, while the processing performance decreased. The tensile strength of the system decrease as the PEG molecular weight increased. The plasticizing system which contents 30% PEG-200(degree of polymerization is 200) shows the maximum elongation at break. The minimum values appeared in both flexural strength and flexural modulus in the CA/PEG-200 system.

scholarly journals PENGARUH LIMBAH ABU PEMBAKARAN BIOMASSA KELAPA SAWIT TERHADAP SIFAT-SIFAT FISIKA DAN MEKANIK HIGH IMPACT POLYSTYRENE

2015 ◽  
Vol 4 (3) ◽  
pp. 23-28
Author(s):  
Fadhilla Asyri ◽  
Kartini Noor Hafni ◽  
A. Haris Simamora
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Impact Strength ◽  
Specific Gravity ◽  
Physical And Mechanical Properties ◽  
High Impact ◽  
Elongation At Break ◽  
Scanning Electron

This study aims was to determine the effect of palm oil fuel ash (POFA) composite as filler on the physical and mechanical properties of high impact polystyrene (HIPS) composites. The research methodology included preparation of raw materials, treatment POFA (hydration process of POFA), mixing using tumbler and then extruder, molding composite specimens, and testing. The variables used were weight ratio of HIPS with 140 mesh POFA at 95/5; 92.5/7.5; 90/10. The composites were tested by Fourier Transform Infrared (FTIR), ash content, specific gravity, tensile strength, elongation at break, impact strength, hardness test, and Scanning Electron Microscopy (SEM). The results of FTIR characterization shows the formation of –OH bonding that was suspected as Si-OH or Si-hydrat. Results of physical and mechanical properties of the composites shows that increase of the filler composition in HIPS-POFA composites until the ratio of 90/10, increase the specific gravity to 7.2% of the original, tensile strength did not change significantly to 28.4 MPa, elongation at break decreased to 2.7%, impact strength decreased to 3.183 KJ/m2, and the hardness increased to 110.5, and Scanning Electron Microscopy (SEM) test show the transformation of POFA structure on treated POFA and intercalation between the matrix and POFA.

Sign in / Sign up

Export Citation Format

Share Document