Improving the Adhesion between Pineapple Leaf Fiber and Natural Rubber by Using Urea Formaldehyde Resin

2019 ◽  
Vol 824 ◽  
pp. 107-113
Author(s):  
Chanaporn Tongphang ◽  
Samar Hajjar ◽  
Karine Mougin ◽  
Taweechai Amornsakchai
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Urea Formaldehyde ◽  
Stress Transfer ◽  
Strain Curve ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Pineapple Leaf Fiber ◽  
Uf Resin ◽  
Leaf Fiber

Green composites, especially that are reinforced with natural fibers, have received a great deal of attention due to the problems of global warming and resources depletion. Pineapple leaf fiber (PALF) is an interesting choice because of its high mechanical properties and it is obtained from agricultural waste. In this work PALF is combined with natural rubber (NR) to produce green rubber composite with enhanced mechanical properties. Since the two materials are so different in their stiffness and polarity, poor interfacial adhesion and thus low stress transfer, between NR and PALF may be expected. Attempts were made to use urea formaldehyde (UF) resin to improve the adhesion between PALF and NR. PALF was coated with different amounts of UF resin in solution. The fiber was characterized with FTIR, XPS and SEM. Uniaxially aligned PALF reinforced rubber composites with a fixed amount of 10 parts per hundred of rubber (phr) PALF were prepared. The adhesion between PALF and NR was evaluated from the tensile stress-strain curve and fracture surface of the composite. It was found that UF resin had negligible effect in improving the stress transfer but rather reduced it as shown in the stress-strain curve. Thicker coating of UF resin led to lower reinforcement effect and, hence, lower modulus. Stress at break, on the other hand, increased with increasing the coating thickness.

Mechanical properties of UN-5100 envelope material for stratospheric airship

2020 ◽  
pp. 1-17
Author(s):  
W.-c. Xie ◽  
X.-l. Wang ◽  
D.-p. Duan ◽  
J.-w. Tang ◽  
Y. Wei
Keyword(s):  
Mechanical Properties ◽  
Significant Role ◽  
Strain Curve ◽  
Image Correlation ◽  
Membrane Structures ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Biaxial Tensile ◽  
Envelope Material ◽  
Biaxial Tensile Testing

ABSTRACT Stratospheric airships are promising aircraft, usually designed as a non-rigid airship. As an essential part of the non-rigid airship, the envelope plays a significant role in maintaining its shape and bearing the external force load. Generally, the envelope material of a flexible airship consists of plain-weave fabric, composed of warp and weft fibre yarn. At present, biaxial tensile experiments are the primary method used to study the stress–strain characteristics of such flexible airship materials. In this work, biaxial tensile testing of UN-5100 material was carried out. The strain on the material under unusual stress and the stress ratio were obtained using Digital Image Correlation (DIC) technology. Also, the stress–strain curve was corrected by polynomial fitting. The slope of the stress–strain curve at different points, the Membrane Structures Association of Japan (MSAJ) standard and the Radial Basis Function (RBF) model were compared to identify the stress–strain characteristics of the materials. Some conclusions on the mechanical properties of the flexible airship material can be drawn and will play a significant role in the design of such envelopes.

Experimental Research on the Stress - Strain Curve of Regional Confined Concrete under Single Axial Press

2014 ◽  
Vol 584-586 ◽  
pp. 1289-1292
Author(s):  
Guo Liang Zhu
Keyword(s):  
Mechanical Properties ◽  
Theoretical Analysis ◽  
Constitutive Model ◽  
Theoretical Basis ◽  
Strain Curve ◽  
Confined Concrete ◽  
Constitutive Relationship ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Relationship Of

Regional confined concrete is base on confined concrete. It is the theory and application of a new attempt and development on confined concrete. To apply it to the actual project, we need to research mechanical properties and establish constitutive relationship of regional confined concrete. According to the research, we had carried on a series of tests, founded the stress-strain constitutive model of regional confined concrete under single axial press. The accuracy of theoretical analysis were more fully verified , and a theoretical basis for the application was provided.

Improving the mechanical properties of short pineapple leaf fiber reinforced natural rubber by blending with acrylonitrile butadiene rubber

2017 ◽  
Vol 57 ◽  
pp. 94-100 ◽  
Author(s):  
Nuttapong Hariwongsanupab ◽  
Sombat Thanawan ◽  
Taweechai Amornsakchai ◽  
Marie-France Vallat ◽  
Karine Mougin
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Butadiene Rubber ◽  
Fiber Reinforced ◽  
Acrylonitrile Butadiene Rubber ◽  
Pineapple Leaf Fiber ◽  
Leaf Fiber

scholarly journals Hybrid-modelling of Mechanical Properties and Thermo-mechanical Behaviour of Chopped Strand Mat Reinforced Thermoset Composites

2020 ◽  
pp. 1-14
Author(s):  
Cornelius Ogbodo Anayo Agbo
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behaviour ◽  
Strain Curve ◽  
Fibre Volume ◽  
Secant Modulus ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Hybrid Modelling ◽  
Thermoset Composites ◽  
Chopped Strand Mat

The concern of this paper is to develop simple workshop application models for predicting the mechanical properties and the evaluation of the thermo-mechanical behaviour of chopped strand fibre-mat reinforced thermoset composites. A hybrid of empirical and strength of materials approach was used at macro- and micro-mechanics levels to model the random fibres which were treated as simple bars within the mat preform and the resulting composite material. The model was validated experimentally by testing wet lay-up produced samples with varying fibre volume fractions and they were found to agree well. The toughness modulus of the composite was also modeled using the secant modulus obtained from the sample’s stress – strain curves of uniform material composites produced at different temperature histories. The toughness modulus determined using the new model was compared with that obtained using the area under the same stress – strain curve computed by Simpson’s rule and the results agreed very well.

Experimental Research on Deformation Properties of Gangue-Paste Filling Material in Mine

2013 ◽  
Vol 734-737 ◽  
pp. 746-750
Author(s):  
Jun Wei Shi
Keyword(s):  
Mechanical Properties ◽  
Uniaxial Compression ◽  
Triaxial Compression ◽  
Strain Curve ◽  
Filling Material ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Deformation Stage ◽  
Plastic Hardening ◽  
Softening Stage

According to the mechanical properties of paste filling body under special environment such as high temperature high humidity high stress and high airtight) in gob, mechanical properties of gangue-paste filling body was studied with the method of field core and laboratory test. The complete stress-strain curve of filling body under the condition of uniaxial and triaxial and the ultimate compressive strength under different confining pressure station were obtained through uniaxial and triaxial compression test. Six stages of uniaxial compression complete stress-strain curve (compression stage, elastic deformation stage, non-stable developing stages, plastic hardening stage, stress softening stage and residual deformation stage) were improved and developed. The deformation characteristics of filling body under triaxial compression were different from that under uniaxial compression. Namely the deformation of filling body under triaxial compression only appeared two deformation stages: linear deformation stage and plastic hardening stage, but had no softening stage basically under different confining pressures, which was benefit for controlling the ground subsidence and preventing the ground buildings.

The Research of Test on Stress-Strain Constitutive Relations of Straw Concrete

2014 ◽  
Vol 584-586 ◽  
pp. 987-992
Author(s):  
Wei Liu ◽  
Wei Xi ◽  
Yi Lu Zhang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Constitutive Relations ◽  
Strain Curve ◽  
Green Building ◽  
Corn Straw ◽  
Stress Strain Curve ◽  
Stress Strain

As a new green building material, straw concrete are introduced about its mechanical properties and characteristics. Mechanical properties test such as prism compressive strength, elastic modulus and Poisson's ratios use standard prismatic blocks. Under different rate of corn straw, cement, sand and fly ash, test gets the full stress-strain curve. Results show that with increase of volume of corn straw, the prism compressive strength reduces significantly. Comparing with natural concrete, elastic modulus of straw concrete can reduces greatly. Poisson’s ratio reduces with increase of volume of corn straw. Fly ash could improve property of the material and replace cement, but excessive replacement will reduce the strength of material.

A hyper-elastic thermal aging constitutive model for rubber-like materials

2019 ◽  
Vol 52 (8) ◽  
pp. 677-700
Author(s):  
Ahmed G Korba ◽  
Abhishek Kumar ◽  
Mark Barkey
Keyword(s):  
Natural Rubber ◽  
Thermal Aging ◽  
Biaxial Loading ◽  
Strain Curve ◽  
Aging Effect ◽  
Elastic Materials ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Hyper Elastic ◽  
Uniaxial And Biaxial Loading

Different phenomenological, empirical, and micromechanical constitutive models have been proposed to describe the behavior of incompressible isotropic hyper-elastic materials. Among these models, very few have accounted for the thermal aging effect on the model constants and parameters. This article introduces a new empirical constitutive hyper-elastic model for thermally aged hyper-elastic materials. The model named “the weight function based (WFB) model” considers the effect of aging temperature and time on its parameters. The WFB model formulation can facilitate fatigue analysis and lifetime prediction of rubber-like materials under aging conditions. The WFB model in this article defines all rubber-like material properties, such as fracture stretch, strength, and stiffness, by predicting the full stress–strain curve at any aging time and temperature. The WFB model was tested on natural rubber for uniaxial and biaxial loading conditions. More than 100 specimens were aged and tested uniaxially under various temperatures and aging times to extract the stress–strain behavior. The temperatures used in the test ranged from 76.7°C to 115.5°C, and the aging time ranged from 0 to 600 hours (hrs). A classical bulge test experiment was generated to extract the biaxial natural rubber material behavior. An ABAQUS finite element analysis model was created to simulate and verify the generated biaxial stress–strain curve. The proposed model represents the aging effect on the tested natural rubber under uniaxial and biaxial loading conditions with an acceptable error margin of less than 10% compared to experimental data.

Experimental Setup for the Determination of Mechanical Solder Materials Properties at Elevated Temperatures

2010 ◽  
Vol 638-642 ◽  
pp. 3793-3798
Author(s):  
Wolfgang H. Müller ◽  
Holger Worrack ◽  
Jens Sterthaus
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Elevated Temperatures ◽  
Young's Modulus ◽  
Linear Optimization ◽  
Strain Curve ◽  
Stress And Strain ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Non Linear

The fabrication of microelectronic and micromechanical devices leads to the use of only very small amounts of matter, which can behave quite differently than the corresponding bulk. Clearly, the materials will age and it is important to gather information on the (changing) material characteristics. In particular, Young’s modulus, yield stress, and hardness are of great interest. Moreover, a complete stress-strain curve is desirable for a detailed material characterization and simulation of a component, e.g., by Finite Elements (FE). However, since the amount of matter is so small and it is the intention to describe its behavior as realistic as possible, miniature tests are used for measuring the mechanical properties. In this paper two miniature tests are presented for this purpose, a mini-uniaxial-tension-test and a nanoindenter experiment. In the tensile test the axial load is prescribed and the corresponding extension of the specimen length is recorded, both of which determines the stress-strain- curve directly. The stress-strain curves are analyzed by assuming a non-linear relationship between stress and strain of the Ramberg-Osgood type and by fitting the corresponding parameters to the experimental data (obtained for various microelectronic solders) by means of a non-linear optimization routine. For a detailed analysis of very local mechanical properties nanoindentation is used, resulting primarily in load vs. indentation-depth data. According to the procedure of Oliver and Pharr this data can be used to obtain hardness and Young’s modulus but not a complete stress-strain curve, at least not directly. In order to obtain such a stress-strain-curve, the nanoindentation experiment is combined with FE and the coefficients involved in the corresponding constitutive equations for stress and strain are obtained by means of the inverse method. The stress-strain curves from nanoindentation and tensile tests are compared for two mate-rials (aluminum and steel). Differences are explained in terms of the locality of the measurement. Finally, material properties at elevated temperature are of particular interest in order to characterize the materials even more completely. We describe the setup for hot stage nanoindentation tests in context with first results for selected materials.

Sign in / Sign up

Export Citation Format

Share Document