Effect of Slag on Engineering Properties of Contamination Soil

2020 ◽  
Vol 857 ◽  
pp. 253-258
Author(s):  
Mohamed Moafak Arbili ◽  
Mohamed Karpuzcu ◽  
Farman Khalil
Keyword(s):  
Shear Strength ◽  
Contaminated Soils ◽  
Engineering Properties ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Additional Material ◽  
Pozzolanic Reactivity ◽  
Density Values ◽  
The Impact ◽  
Water Contents

In this study investigates utilizing of slag as an additional material to improve engineering properties of contaminated soil by crude oil to changing the engineering characteristics to be satisfying and compatible, this is due to its pozzolanic reactivity. The aim of this study the impact of slag material in geotechnical engineering and to stabilize properties of contaminated soils. Two percentages of slag were utilized in this study, which is 0% and 6%. Compaction and direct shear strength tests had been conducted on the artificial contaminated prepared soil samples. In the results, showed that the increasing of slag leads to a decrease in the optimum water contents while the maximum dry density values increase. Furthermore, the shear strength is improved by utilizing slag so that slag can be considered as a stabilizing material to improve the properties of contamination soil.

scholarly journals Effects of contamination with gasoline on engineering properties of fine-grained silty soils with an emphasis on the duration of exposure

2021 ◽  
Vol 3 (7) ◽  
Author(s):  
Abdollah Yazdi ◽  
Ebrahim Sharifi Teshnizi
Keyword(s):  
Contaminated Soils ◽  
Geotechnical Properties ◽  
Engineering Properties ◽  
Contamination Level ◽  
Dry Density ◽  
Compression Tests ◽  
Maximum Dry Density ◽  
Silty Soil ◽  
Geochemical Properties ◽  
Laboratory Results

AbstractLeaking tanks may lead to severe contamination of their surrounding soil. The geotechnical behavior of the soil varies with the physicochemical processes that occur between the contaminant and the soil. In this respect, studying the geochemical properties of gasoline-contaminated soils and sediments seems to be important for engineering and especially environmental purposes. In this paper, laboratory tests were carried out to examine the effects of crude gasoline contamination on some of the geotechnical properties of a silty soil sampled from the Mashhad plain, located in the northeast of Iran. Tests consisted of basic properties, Atterberg limits, compaction, direct shear, and uniaxial compression tests, which were carried out on clean and contaminated soil samples at the same densities. The contaminated samples were prepared by mixing the soils with crude gasoline in the amounts of 3%, 6%, 9%, and 12% of dry weight and curing periods of 0, 7, 15, and 30 days. Results indicated a decrease in the friction angle and an increase in the cohesion of the soil by increasing gasoline content. Besides, a reduction in the maximum dry density and optimum moisture content was observed in the compaction test. The increase in gasoline percentage up to 6% also showed a direct effect on increasing the liquid limit and plastic limit of silty soil, which decreased thereafter. Moreover, any increase in gasoline percentage had a reverse effect on the modulus of elasticity of the soil. The increase in gasoline percentage up to 3% also had a direct impact on the uniaxial compressive strength of the soil, exceeding which it started to decline. Finally, the effects of contamination duration were examined by testing contaminated samples in periods of 7, 15, and 30 days under natural conditions. The results showed a reverse relationship with all geotechnical properties due to aging and a reduction in the gasoline content due to the evaporation of volatile compounds. Also, the numerical analysis of the laboratory results indicated an increase in settling and the percentage of shear strain beneath the foundation with increasing the contamination level, confirming the laboratory results.

Effect of Groundnut Shell Ash on Laterite Soils Stabilized with Lime for Civil Structures

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Oluwaseun A. Adetayo ◽  
◽  
Olugbenga O. Amu ◽  
Feyidamilola Faluyi ◽  
Emmanuel Akinyele ◽  
...  
Keyword(s):  
Shear Strength ◽  
Local Government ◽  
Local Government Area ◽  
Engineering Properties ◽  
Lateritic Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Civil Structures ◽  
Groundnut Shell ◽  
Groundnut Shell Ash

This study considered the practicality of groundnut shell ash (GSA) on laterite stabilized with lime for civil structures. Three site locations of lateritic soil named specimen I, II and III were assembled from Ifewara, Atakunmosa West Local Government Area, Ilesa East Local Government Area, and Ilesa West Local Government, all situated in Osun State, Nigeria. Preliminary tests were wrapped up on the soil specimens in their characteristic states and when stabilized with optimum lime. Compaction, California Bearing Ratio (CBR) and undrained triaxial shear strength tests were performed when fluctuating paces of 2 %, 4 %, 6 %, and 8 % of GSA were included to the soil specimens at optimum lime. The Atterberg limits tests showed a critical decrease in plasticity index for all the soil specimens when stabilized with lime. Compaction test showed a lessening in the maximum dry density from 1732 kg/m3 to 1651 kg/m3 for specimen I, 1874 kg/m3 to 1621 kg/m3 for specimen II and 1683 kg/m3 to 1655 kg/m3 for specimen III on stabilizing with lime, presentation of GSA to stabilized lime-soil decreases the maximum dry density for all the soil specimen with specimen I diminished to 1642 kg/m3, 1595 kg/m3, 1611 kg/m3 and 1611 kg/m3 at 2 %, 4 %, 6 % and 8 % GSA substances individually. Addition of GSA substances enhanced the engineering properties of laterite stabilized with lime as the unsoaked CBR values expanded for all the soil specimens. At optimum lime measurements, addition of 4 % GSA expanded the shear strength to 110.74 kN/m2 and 127.53 kN/m2 for specimens I and II individually while at 6 % GSA addition, the shear strength of specimen III was peak 118.24 kN/m2. The expansion in shear strength further affirms the improvement prior shown in the geotechnical properties of lateritic soil with the addition of groundnut shell ash. addition of 2 % GSA content extended the triaxial shear strength from 60.43kN/m2 to 188.36kN/m2 for specimen I, and at 4% GSA content, both soil specimens II and III expanded from 19.19kN/m2 to 201.48kN/m2 and 30.62kN/m2 to 111.65kN/m2 separately. Conclusively, GSA improved the durability and strength of lateritic soils stabilized with lime for civil structures.

Interior Experimental Study on Engineering Properties of the Modified Tonhaltig Phyllite

2011 ◽  
Vol 243-249 ◽  
pp. 2586-2590 ◽  
Author(s):  
Xin Ping Li ◽  
Ya Ni Lu ◽  
Xing Hong Wu
Keyword(s):  
Engineering Application ◽  
Soft Rock ◽  
Engineering Properties ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Soft Rocks ◽  
Optimum Water Content ◽  
Principal Effect ◽  
Optimum Water ◽  
Water Contents

In view of the fact that large amounts of tonhaltig phyllite were found along the Shi-Tian expressway line, these soft rocks could not meet the roadbed filling requirements. It was necessary to improve the weathered soft rocks to satisfy the engineering demands. Interior comparative tests research on seven modified methods were carried out such as part in different proportions of cement、sand or stone bits, with soft rock of different water contents being artificial to mix and stir evenly, then unconfined compression strength of the samples at different cement quantity、different curing ages were compared; the optimum water content and and maximum dry density were determined through the compaction test; In addition, the principal effect of CBR value was analyzed. thus the best modified way was defined, the aim was to provide reference of theory and examination for further design and engineering application on weathered rock of expressway roadbed construction.

Effect of Lime on Compaction, Strength and Consolidation Characteristics of Pontian Marine Clay

2015 ◽  
Vol 72 (3) ◽  
Author(s):  
Siaw Yah Chong ◽  
Khairul Anuar Kassim
Keyword(s):  
Construction Material ◽  
Soft Clay ◽  
Engineering Properties ◽  
Dry Density ◽  
Marine Clay ◽  
Maximum Dry Density ◽  
Stabilization Phase ◽  
Compaction Curve ◽  
Stabilized Soil

Marine clay is a problematic construction material, which is often encountered in Malaysian coastal area. Previous researchers showed that lime stabilization effectively enhanced the engineering properties of clay. For soft clay, both strength and consolidation characteristics are equally important to be fully understood for design purpose. This paper presented the effect of lime on compaction, strength and consolidation characteristics of Pontian marine clay. Compaction, unconfined compression, direct shear, Oedometer and falling head permeability tests were conducted on unstabilized and lime stabilized samples at various ages. Specimens were prepared by compaction method based on 95 percent maximum dry density at the wetter side of compaction curve. It was found that lime successfully increased the strength, stiffness and workability of Pontian marine clay; however, the permeability was reduced. Unconfined compressive strength of stabilized soil was increased by 49 percent at age of 56 days whereas compressibility and permeability was reduced by 48 and 67 percent, respectively. From laboratory tests, phenomenon of inconsistency in engineering characteristics was observed for lime stabilized samples below age of 28 days. This strongly proved that lime stabilized soil underwent modification phase before stabilization phase which provided the long term improvement.

scholarly journals Geotechnical Properties of Fresh and Degraded MSW in the Foothill of Shivalik Range Una, Himachal Pradesh

2019 ◽  
Vol 8 (2) ◽  
pp. 363-374 ◽  
Keyword(s):  
Moisture Content ◽  
Himachal Pradesh ◽  
Engineering Properties ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Overburden Pressure ◽  
Dump Site ◽  
Angle Of Internal Friction ◽  
Geotechnical Characteristics ◽  
Geotechnical Tests

The aim of the present study is to determine the physical and geotechnical characteristics of municipal solid waste (MSW) from an open dump site located in Una town, Himachal Pradesh (India) for the analysis of settlement and structural stability of landfill. Degraded waste was tested for different time intervals ranging from 6 months to 6 years. The physical characterization and the geotechnical tests were performed to determine the composition and the engineering properties of MSW respectively. The presence of moisture content in the fresh waste was 49.5±1.05% but for the degraded (or old) waste it varied between 39.8 to 51.6%. The specific gravity of fresh and old waste varied between 1.83±0.05 and 1.85 for 6 months old waste and 2.28 for 5-6 years old degraded waste respectively. The maximum dry density (MDD) was observed to be 4.28 kN/m2 for fresh waste at the optimum moisture content (OMC) of 78.1% and 4.47 kN/m3 for 6 months old waste and 6.25 kN/m3 for the degraded waste of 5-6 years at 80.2, 85.4% of OMC respectively. The hydraulic conductivity (k) of MSW was found to be decreasing with the degradation of MSW and the overburden pressure whereas the shear strength increased along with the degradation of the waste. The cohesion (c) and angle of internal friction (φ) increased respectively from 31.2 kPa(fresh) to 38 kPa(degraded) and 14° to 22° with the increase in waste degradation. The compression ratio of fresh waste was within the ranges of 0.19-0.29 and for degraded MSW it varied between 0.12 for 6 months old waste and 0.17 for 5-6 years old degraded waste respectively.

scholarly journals Effect of Sand Percentage on the Compaction Properties and Undrained Shear Strength of Low Plasticity Clay

2021 ◽  
Vol 9 (1) ◽  
pp. 16-20
Author(s):  
Iyad Alkroosh ◽  
Ali Al-Robay ◽  
Prabir Sarker ◽  
Saif Alzabeebee
Keyword(s):  
Shear Strength ◽  
Moisture Content ◽  
Undrained Shear Strength ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Sand Content ◽  
Compression Tests ◽  
Maximum Dry Density ◽  
Sand Mixture ◽  
Undrained Shear

This paper investigates the influence of sand content on the mechanical behavior of a low plasticity clay that collected from south of Iraq (Sumer town). Samples have been prepared with sand contents of 0%, 10%, 20%, 30%, and 40% of the clay weight. Standard Proctor and unconfined compression tests have been carried out and the optimum moisture content, maximum dry density, and undrained shear strength have been determined. The results show a gradual increasing trend of the maximum dry density with the increase of the sand content up to 30%. The highest dry density reaches 1.90 g/cm3 corresponding to an optimum moisture content of 12%. In addition, this paper shows that the undrained shear strength is inversely proportional to the increase of the percentage of sand. The results of this work provide a useful addition to the literature regarding the behaviour or low plasticity clay-sand mixture.

Shear Strength of BC-Soil Admixed with Lime and Bio-Enzyme

2019 ◽  
Vol 969 ◽  
pp. 327-334
Author(s):  
C. Jairaj ◽  
M.T. Prathap Kumar ◽  
H. Muralidhara
Keyword(s):  
Shear Strength ◽  
Soil Stabilization ◽  
Morphological Changes ◽  
Ground Improvement ◽  
High Strength ◽  
Sem Analysis ◽  
Dry Density ◽  
Test Results ◽  
Maximum Dry Density ◽  
Lime Content

This BC Soil are expansive in nature and are problematic because of low shear strength and high compressibility. Review of literatures have proven that addition of lime imparts high strength with a corresponding reduction in swell of BC soils. In addition, Bio-enzymes have also been found to play a key role as activators in improving the characteristics of clayey soils such as BC soil. Development and use of non-traditional ground improvement techniques such as bio-enzymes in combination with lime for soil stabilization helps to reduce the cost and the detrimental effects on the soil environment. In the present study lime and bio-enzymes were used as soil stabilizing agents. Compaction test results on BC soil admixed with different percent of lime indicated that 3% addition lime gives higher maximum dry density of 17kN/m3 with OMC of 21% compare to other addition of lime percentages. Keeping 3% of lime as optimum lime content(OLC), BC Soil was admixed with different dosages of Bio-enzymes 25ml/m3, 50ml/m3, 100 ml/m3,150ml/m3, and 200ml/m3 along with OLC was tested for compaction and unconfined compressive strength(UCC). Further UCC test was carried out for different curing period of 0, 7, 15, 30, and 60 Days to analyse the long term effect of BC soil admixed with bio-enzymes with and without lime content. Morphological and chemical analysis was done by using XRD and SEM analysis, from all the test results it was found that 3%OLC + 75ml/m3 of bio-enzymes for 7 day of curing gives higher UCC of 450 kPa. From the SEM it was found that better bond between particles found to develop in bio-enzyme+ lime admixed BC soil in comparison with lime alone admixed BC soil. XRD studies indicated morphological changes in crystallinity and structure of stabilized BC soil in comparison to BC soil alone.

scholarly journals Influence of admixture of Bamboo leaf ash and lime on the Compaction characteristics of lateritic soil

2021 ◽  
Vol 6 (1) ◽  
Author(s):  
I. O Ameen
Keyword(s):  
Moisture Content ◽  
Soil Sample ◽  
Optimum Moisture Content ◽  
Lateritic Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
British Standard ◽  
Bamboo Leaf Ash ◽  
The Impact ◽  
Sample Maximum

This study investigated the impact of compactive efforts on A-7-5 lateritic soil stabilized with Bamboo Leaf Ash (BLA) mixed with lime. Preliminary tests were conducted on the soil sample for identification and classification. Compaction tests (using British Standard Light (BSL), British Standard Heavy (BSH) and West Africa Standard (WAS) compactive efforts) were performed on the sample in both natural and stabilized states by incorporating 2, 4, 6 and 8% Bamboo Leaf Ash mixed together with 1, 2, and 3% lime by weight of soil sample. Maximum dry density (MDD) increased to 1766 kg/m3 at 3% lime and 6% BLA, 1818 kg/m3 at 3% lime and 8% BLA and 1866 kg/m3 at 3% lime and 2% BLA while the optimum moisture content decreased to 12.70% at 3% and lime 8% BLA, 11.40% at 2% lime 6% BLA and 11.12% at 3% lime and 2% BLA for BSL, WAS and BSH, respectively. Based on these findings, the addition of lime-BLA enhanced the soil and has a promising prospect for stabilization of lateritic soil.

scholarly journals Investigation on the performance of ‘Fino’ materials to stabilize expansive soil: A case study in Yeka Sub-City, Addis Ababa, Ethiopia

2021 ◽  
Vol 6 (2) ◽  
pp. 044-050
Author(s):  
Tsion Mindaye ◽  
Emer Tucay Quezon ◽  
Temesgen Ayna
Keyword(s):  
Soil Stabilization ◽  
Addis Ababa ◽  
Research Result ◽  
Expansive Soil ◽  
Liquid Limit ◽  
Engineering Properties ◽  
Natural State ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Proctor Test

Expansive soil swells when it is wet, and it will shrink when it dries. Due to this behavior of the soil, the strength and other properties of soil are inferior. To improve its properties, it is necessary to stabilize the soil with different stabilizers. Soil stabilization is a process to treat the soil to maintain, alter, or improve expansive soil performance. In this study, the potential of 'Fino' as stabilizing additive to expansive soil was investigated for the improving engineering properties of expansive soil to be used as subgrade material. The evaluation involved the determination of the Free Swell test, CBR test, Atterberg's limits, and the Proctor test of expansive soil in its natural state as well as when mixed with varying proportions of 'Fino.' The practices were performed on six proportions 5%, 10%, 15%, 20%, 25% and 30 % with expansive soil. The research result indicated a considerable reduction in Swelling, and the Maximum dry Density of soil was improved. Optimum moisture content decreased in increasing 'Fino.' At 30% of 'Fino,' the CBR values of expansive soil increased from 1.06% to 5.94%, Liquid Limit decreased from 95.2% to 29.4%, plasticity index decreased from 57.24% to 17.82% and the degree of expansion of the natural subgrade soil has reduced from "very high to medium." Hence, it is concluded that the 'Fino' at 30% has shown significant improvement in the expansive soil's engineering properties meeting the ERA and AASHTO Standard specifications requirements for road subgrade material.

Effect of sand percentage on the compaction properties and undrained shear strength of low plasticity soft clay

2021 ◽  
Author(s):  
Iyad Alkroosh ◽  
◽  
Ali Al-Robay ◽  
Prabir Sarker ◽  
Saif Alzabeebee ◽  
...  
Keyword(s):  
Shear Strength ◽  
Moisture Content ◽  
Soft Clay ◽  
Undrained Shear Strength ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Sand Content ◽  
Compression Tests ◽  
Maximum Dry Density ◽  
Undrained Shear

This study investigated the influence of sand content on the mechanical behaviour of a low plasticity clay found in Iraq. Samples were prepared with sand contents of 0%, 10%, 20%, 30%, and 40% of the weight of the clay. Standard Proctor and unconfined compression tests were carried out and the optimum moisture content, maximum dry density, and undrained shear strength were determined. The results showed a gradual increasing trend of the maximum dry density with the increase of the sand content up to 30%. The highest dry density reached was 1.90 gm/cm3 corresponding to an optimum moisture content of 12%. In addition, it was also found that the undrained shear strength was inversely proportional to the increase of the percentage of sand. Thus, the dry density of the clay could be increased well above 1.70 g/cm3, which is the minimum dry density accepted as a compacted subgrade according to the Iraqi General Specifications for Roads and Bridges (2003); hence, the rejected low plasticity clay could be utilised by mixing with sand. The reasons for the increase of the dry density and the decrease of the undrained shear strength has been extensively discussed in the paper.

Sign in / Sign up

Export Citation Format

Share Document