scholarly journals Effects of contamination with gasoline on engineering properties of fine-grained silty soils with an emphasis on the duration of exposure

2021 ◽  
Vol 3 (7) ◽  
Author(s):  
Abdollah Yazdi ◽  
Ebrahim Sharifi Teshnizi
Keyword(s):  
Contaminated Soils ◽  
Geotechnical Properties ◽  
Engineering Properties ◽  
Contamination Level ◽  
Dry Density ◽  
Compression Tests ◽  
Maximum Dry Density ◽  
Silty Soil ◽  
Geochemical Properties ◽  
Laboratory Results

AbstractLeaking tanks may lead to severe contamination of their surrounding soil. The geotechnical behavior of the soil varies with the physicochemical processes that occur between the contaminant and the soil. In this respect, studying the geochemical properties of gasoline-contaminated soils and sediments seems to be important for engineering and especially environmental purposes. In this paper, laboratory tests were carried out to examine the effects of crude gasoline contamination on some of the geotechnical properties of a silty soil sampled from the Mashhad plain, located in the northeast of Iran. Tests consisted of basic properties, Atterberg limits, compaction, direct shear, and uniaxial compression tests, which were carried out on clean and contaminated soil samples at the same densities. The contaminated samples were prepared by mixing the soils with crude gasoline in the amounts of 3%, 6%, 9%, and 12% of dry weight and curing periods of 0, 7, 15, and 30 days. Results indicated a decrease in the friction angle and an increase in the cohesion of the soil by increasing gasoline content. Besides, a reduction in the maximum dry density and optimum moisture content was observed in the compaction test. The increase in gasoline percentage up to 6% also showed a direct effect on increasing the liquid limit and plastic limit of silty soil, which decreased thereafter. Moreover, any increase in gasoline percentage had a reverse effect on the modulus of elasticity of the soil. The increase in gasoline percentage up to 3% also had a direct impact on the uniaxial compressive strength of the soil, exceeding which it started to decline. Finally, the effects of contamination duration were examined by testing contaminated samples in periods of 7, 15, and 30 days under natural conditions. The results showed a reverse relationship with all geotechnical properties due to aging and a reduction in the gasoline content due to the evaporation of volatile compounds. Also, the numerical analysis of the laboratory results indicated an increase in settling and the percentage of shear strain beneath the foundation with increasing the contamination level, confirming the laboratory results.

Effect of Slag on Engineering Properties of Contamination Soil

2020 ◽  
Vol 857 ◽  
pp. 253-258
Author(s):  
Mohamed Moafak Arbili ◽  
Mohamed Karpuzcu ◽  
Farman Khalil
Keyword(s):  
Shear Strength ◽  
Contaminated Soils ◽  
Engineering Properties ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Additional Material ◽  
Pozzolanic Reactivity ◽  
Density Values ◽  
The Impact ◽  
Water Contents

In this study investigates utilizing of slag as an additional material to improve engineering properties of contaminated soil by crude oil to changing the engineering characteristics to be satisfying and compatible, this is due to its pozzolanic reactivity. The aim of this study the impact of slag material in geotechnical engineering and to stabilize properties of contaminated soils. Two percentages of slag were utilized in this study, which is 0% and 6%. Compaction and direct shear strength tests had been conducted on the artificial contaminated prepared soil samples. In the results, showed that the increasing of slag leads to a decrease in the optimum water contents while the maximum dry density values increase. Furthermore, the shear strength is improved by utilizing slag so that slag can be considered as a stabilizing material to improve the properties of contamination soil.

scholarly journals Experimental Study on the Utilization of Fine Steel Slag on Stabilizing High Plastic Subgrade Soil

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Hussien Aldeeky ◽  
Omar Al Hattamleh
Keyword(s):  
Steel Slag ◽  
Dry Weight ◽  
Geotechnical Properties ◽  
Engineering Properties ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Geotechnical Characteristics ◽  
Subgrade Soil ◽  
Free Swell ◽  
High Plastic

The three major steel manufacturing factories in Jordan dump their byproduct, steel slag, randomly in open areas, which causes many environmental hazardous problems. This study intended to explore the effectiveness of using fine steel slag aggregate (FSSA) in improving the geotechnical properties of high plastic subgrade soil. First soil and fine steel slag mechanical and engineering properties were evaluating. Then 0%, 5%, 10%, 15%, 20%, and 25% dry weight of soil of fine steel slag (FSSA) were added and mixed into the prepared soil samples. The effectiveness of the FSSA was judged by the improvement in consistency limits, compaction, free swell, unconfined compression strength, and California bearing ratio (CBR). From the test results, it is observed that 20% FSSA additives will reduce plasticity index and free swell by 26.3% and 58.3%, respectively. Furthermore, 20% FSSA additives will increase the unconfined compressive strength, maximum dry density, and CBR value by 100%, 6.9%, and 154%. By conclusion FSSA had a positive effect on the geotechnical properties of the soil and it can be used as admixture in proving geotechnical characteristics of subgrade soil, not only solving the waste disposal problem.

scholarly journals Effect of Calcium Chloride on Geotechnical Properties of Black Cotton Soil Ramya

2018 ◽  
Vol 2 (1) ◽  
Keyword(s):  
Calcium Chloride ◽  
Liquid Limit ◽  
Geotechnical Properties ◽  
Engineering Properties ◽  
Black Cotton Soil ◽  
Dry Density ◽  
Unconfined Compression ◽  
Maximum Dry Density ◽  
Treated Soil ◽  
Curing Period

The objective of the present study was to understand the effect of calcium chloride on geotechnical properties of black cotton soil. Black cotton soil collected from Siraguppa taluk, Bellary. It was subjected to various concentrations of calcium chloride viz. 0.1 N, 0.5 N, 1.0 N, 2.0 N and 4.0 N. Attempt was made to understand the effect of calcium chloride on index properties and engineering properties of black cotton soil. It was observed that the values of liquid limit, plastic limit and plasticity index of the soil treated with calcium chloride was decreasing with increase in concentration. Further the treated soil was investigated for compaction test. It was observed that the maximum dry density of the soil was increasing at higher concentrations. However, no remarkable changes were observed in the values of optimum moisture content with increase in concentration of calcium chloride. The laboratory investigation was made to obtain the unconfined compression strength (UCS) of treated soil. The soil was cured for 1 day, 7, 14 and 28 days. It was observed that the values of UCS were increasing with increase in concentration at any curing period. The soil was further tested to obtain the effect of calcium chloride on permeability of treated soil. It was observed that the permeability is increasing with increase in concentrations of 0 N, 0.5 N, and 4.0 N.

scholarly journals Use of Reservoir Sediments to Improve Engineering Properties of Dune Sand in Oman

2021 ◽  
Vol 11 (4) ◽  
pp. 1620
Author(s):  
Mohsin Usman Qureshi ◽  
Maryam Alsaidi ◽  
Mubashir Aziz ◽  
Ilhan Chang ◽  
Ali Murtaza Rasool ◽  
...  
Keyword(s):  
Binary Mixture ◽  
Engineering Properties ◽  
Dry Density ◽  
Compression Tests ◽  
Dune Sand ◽  
Maximum Dry Density ◽  
Uniformity Coefficient ◽  
Fine Grained ◽  
Sediment Content ◽  
Optimum Water Content

Managing sediments dredged from reservoirs of recharge dams is an environmental issue, however, these sediments can be an abundant and economical source of fine-grained fill soil. This experimental investigation quantifies the geotechnical properties of a reservoir sediment used to improve engineering properties of a poorly graded dune sand in Oman. The binary mixes were prepared with different percentages (5, 10, 20, 50, 75, 90, 95%) of sediment with sand. Laboratory tests such as gradation, consistency limits, compaction, and unconfined compression tests were performed to measure the engineering characteristics of the binary mixtures. The results showed that the maximum dry density increases up to a sediment content of 50% and then decreases with further increase in the sediment content. The optimum water content increases with the increase in sediment content from 17% for pure sand to 22.5% for pure sediment. The optimum moisture content shows a good correlation with the plastic limit of the binary mixture of sand and sediment. The unconfined compressive strength substantially increases with sediment content up to 75% and then decreases with further increase in the sediment content. The binary mixture of sand sediment is sensitive to moisture, however, the order of strength stability against moisture is dune sand mixed with 75, 50, and 20% sediments. The addition of sediment to dune sand improved the uniformity coefficient to some extent with an increase in the maximum and minimum void ratios as well. The elemental analysis of the sediment confirms that the material is non-contaminated and can be employed in geotechnical engineering applications as a sustainable and environmentally friendly solution.

Effect of Lime on Compaction, Strength and Consolidation Characteristics of Pontian Marine Clay

2015 ◽  
Vol 72 (3) ◽  
Author(s):  
Siaw Yah Chong ◽  
Khairul Anuar Kassim
Keyword(s):  
Construction Material ◽  
Soft Clay ◽  
Engineering Properties ◽  
Dry Density ◽  
Marine Clay ◽  
Maximum Dry Density ◽  
Stabilization Phase ◽  
Compaction Curve ◽  
Stabilized Soil

Marine clay is a problematic construction material, which is often encountered in Malaysian coastal area. Previous researchers showed that lime stabilization effectively enhanced the engineering properties of clay. For soft clay, both strength and consolidation characteristics are equally important to be fully understood for design purpose. This paper presented the effect of lime on compaction, strength and consolidation characteristics of Pontian marine clay. Compaction, unconfined compression, direct shear, Oedometer and falling head permeability tests were conducted on unstabilized and lime stabilized samples at various ages. Specimens were prepared by compaction method based on 95 percent maximum dry density at the wetter side of compaction curve. It was found that lime successfully increased the strength, stiffness and workability of Pontian marine clay; however, the permeability was reduced. Unconfined compressive strength of stabilized soil was increased by 49 percent at age of 56 days whereas compressibility and permeability was reduced by 48 and 67 percent, respectively. From laboratory tests, phenomenon of inconsistency in engineering characteristics was observed for lime stabilized samples below age of 28 days. This strongly proved that lime stabilized soil underwent modification phase before stabilization phase which provided the long term improvement.

scholarly journals Geotechnical Properties of Fresh and Degraded MSW in the Foothill of Shivalik Range Una, Himachal Pradesh

2019 ◽  
Vol 8 (2) ◽  
pp. 363-374 ◽  
Keyword(s):  
Moisture Content ◽  
Himachal Pradesh ◽  
Engineering Properties ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Overburden Pressure ◽  
Dump Site ◽  
Angle Of Internal Friction ◽  
Geotechnical Characteristics ◽  
Geotechnical Tests

The aim of the present study is to determine the physical and geotechnical characteristics of municipal solid waste (MSW) from an open dump site located in Una town, Himachal Pradesh (India) for the analysis of settlement and structural stability of landfill. Degraded waste was tested for different time intervals ranging from 6 months to 6 years. The physical characterization and the geotechnical tests were performed to determine the composition and the engineering properties of MSW respectively. The presence of moisture content in the fresh waste was 49.5±1.05% but for the degraded (or old) waste it varied between 39.8 to 51.6%. The specific gravity of fresh and old waste varied between 1.83±0.05 and 1.85 for 6 months old waste and 2.28 for 5-6 years old degraded waste respectively. The maximum dry density (MDD) was observed to be 4.28 kN/m2 for fresh waste at the optimum moisture content (OMC) of 78.1% and 4.47 kN/m3 for 6 months old waste and 6.25 kN/m3 for the degraded waste of 5-6 years at 80.2, 85.4% of OMC respectively. The hydraulic conductivity (k) of MSW was found to be decreasing with the degradation of MSW and the overburden pressure whereas the shear strength increased along with the degradation of the waste. The cohesion (c) and angle of internal friction (φ) increased respectively from 31.2 kPa(fresh) to 38 kPa(degraded) and 14° to 22° with the increase in waste degradation. The compression ratio of fresh waste was within the ranges of 0.19-0.29 and for degraded MSW it varied between 0.12 for 6 months old waste and 0.17 for 5-6 years old degraded waste respectively.

scholarly journals Effect of Sand Percentage on the Compaction Properties and Undrained Shear Strength of Low Plasticity Clay

2021 ◽  
Vol 9 (1) ◽  
pp. 16-20
Author(s):  
Iyad Alkroosh ◽  
Ali Al-Robay ◽  
Prabir Sarker ◽  
Saif Alzabeebee
Keyword(s):  
Shear Strength ◽  
Moisture Content ◽  
Undrained Shear Strength ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Sand Content ◽  
Compression Tests ◽  
Maximum Dry Density ◽  
Sand Mixture ◽  
Undrained Shear

This paper investigates the influence of sand content on the mechanical behavior of a low plasticity clay that collected from south of Iraq (Sumer town). Samples have been prepared with sand contents of 0%, 10%, 20%, 30%, and 40% of the clay weight. Standard Proctor and unconfined compression tests have been carried out and the optimum moisture content, maximum dry density, and undrained shear strength have been determined. The results show a gradual increasing trend of the maximum dry density with the increase of the sand content up to 30%. The highest dry density reaches 1.90 g/cm3 corresponding to an optimum moisture content of 12%. In addition, this paper shows that the undrained shear strength is inversely proportional to the increase of the percentage of sand. The results of this work provide a useful addition to the literature regarding the behaviour or low plasticity clay-sand mixture.

Investigation to some Preliminary Geotechnical Properties of Soft Clay Stabilized by Fly Ash Based Geopolymers

2020 ◽  
Vol 857 ◽  
pp. 259-265
Author(s):  
Jasim M. Abbas ◽  
Amer M Ibrahim ◽  
Abdalla M. Shihab
Keyword(s):  
Fly Ash ◽  
Specific Gravity ◽  
Soft Clay ◽  
Cost Effective ◽  
Geotechnical Properties ◽  
Experimental Program ◽  
Dry Density ◽  
Alkali Activation ◽  
Plastic Behavior ◽  
Maximum Dry Density

The civil engineering projects that includes soft clay within its activities has a serious concern of hazards, such hazards can be overcame by treating the existing soils by certain materials which are named as "stabilizers". The common materials that are highly used in this field are ordinary Portland cement, fly ash, lime and rice husk ash, etc. Each one of these stabilizers has its known shortcomings. The alkali activation of any alumina silicate source produces some kind of cost effective primary binding gel which is known as "Geopolymers". This study is devoted to investigate the role of liquid over fly ash ratio to some soil – FA based Geopolymers geotechnical properties. Such ratio is taken as 2.71, 3.167, 3.8 and 4.75 respectively within the experimental program and the investigated geotechnical properties are the specific gravity, liquid and plastic limit, compaction characteristics and California bearing ratio. The tests results showed that the maximum dry density decreased about 42 % at 2.71 liq/FA whereas this the specific gravity decreased 27 % at the same this ratio. In addition, the 3.8 and 4.75 of such limits revealed no plastic behavior due to the high presence of liquid.

scholarly journals Evolution of the Geotechnical Properties of Fly Ash Stabilized Silty Soil Activated by Graphene Oxide (GO)

2019 ◽  
Vol 8 (2) ◽  
pp. 4732-4737 ◽  
Keyword(s):  
Graphene Oxide ◽  
Fly Ash ◽  
Soil Stabilization ◽  
Dry Density ◽  
Unconfined Compression ◽  
Maximum Dry Density ◽  
Unconfined Compression Test ◽  
Soil Matrix ◽  
Silty Soil ◽  
Limit Test

At present time, there are vastly available of various nanomaterials, by using this material it plays an important role in various applications along with geotechnical soil stabilization/strengthen techniques. In the present investigation the addition of Graphene Oxide (GO) solution as nanomaterial into the low cemented fly ash (Class F – fly ash) to improving various properties of a local available silty soil. The various tests such as light compaction test, unconfined compression test, direct shear test, liquid limit, and plastic limit test were performed on the newly formed matrix to check their respective behavior to stimulated actual site condition on the given matrix in the laboratory. Also Scanning Electron Microscopy (SEM) analysis was performed to study the structure of the newly formed matrix. The addition of small proportion GO in original soil-fly ash matrix decrease the plasticity index and at the same time increase the maximum dry density, unconfined compression strength, and cohesion value help to use newly soil matrix effectively.

scholarly journals Investigation on the performance of ‘Fino’ materials to stabilize expansive soil: A case study in Yeka Sub-City, Addis Ababa, Ethiopia

2021 ◽  
Vol 6 (2) ◽  
pp. 044-050
Author(s):  
Tsion Mindaye ◽  
Emer Tucay Quezon ◽  
Temesgen Ayna
Keyword(s):  
Soil Stabilization ◽  
Addis Ababa ◽  
Research Result ◽  
Expansive Soil ◽  
Liquid Limit ◽  
Engineering Properties ◽  
Natural State ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Proctor Test

Expansive soil swells when it is wet, and it will shrink when it dries. Due to this behavior of the soil, the strength and other properties of soil are inferior. To improve its properties, it is necessary to stabilize the soil with different stabilizers. Soil stabilization is a process to treat the soil to maintain, alter, or improve expansive soil performance. In this study, the potential of 'Fino' as stabilizing additive to expansive soil was investigated for the improving engineering properties of expansive soil to be used as subgrade material. The evaluation involved the determination of the Free Swell test, CBR test, Atterberg's limits, and the Proctor test of expansive soil in its natural state as well as when mixed with varying proportions of 'Fino.' The practices were performed on six proportions 5%, 10%, 15%, 20%, 25% and 30 % with expansive soil. The research result indicated a considerable reduction in Swelling, and the Maximum dry Density of soil was improved. Optimum moisture content decreased in increasing 'Fino.' At 30% of 'Fino,' the CBR values of expansive soil increased from 1.06% to 5.94%, Liquid Limit decreased from 95.2% to 29.4%, plasticity index decreased from 57.24% to 17.82% and the degree of expansion of the natural subgrade soil has reduced from "very high to medium." Hence, it is concluded that the 'Fino' at 30% has shown significant improvement in the expansive soil's engineering properties meeting the ERA and AASHTO Standard specifications requirements for road subgrade material.

Sign in / Sign up

Export Citation Format

Share Document