Reactive Ion Etching Induced Surface Damage of Silicon Carbide

2005 ◽  
Vol 483-485 ◽  
pp. 765-768 ◽  
Author(s):  
Jun Hai Xia ◽  
E. Rusli ◽  
R. Gopalakrishnan ◽  
S.F. Choy ◽  
Chin Che Tin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Reactive Ion Etching ◽  
Surface Damage ◽  
Textured Surface ◽  
Rf Power ◽  
Power Devices ◽  
Ion Etching ◽  
Maximum Value ◽  
Wide Range ◽  
Coarse Surface

Reactive ion etching of SiC induced surface damage, e.g., micromasking effect induced coarse and textured surface, is one of the main concerns in the fabrication of SiC based power devices [1]. Based on CHF3 + O2 plasma, 4H-SiC was etched under a wide range of RF power. Extreme coarse and textured etched surfaces were observed under certain etching conditions. A super-linear relationship was found between the surface roughness and RF power when the latter was varied from 40 to 160 W. A further increase in the RF power to 200 W caused the surface roughness to drop abruptly from its maximum value of 182.4 nm to its minimum value of 1.3 nm. Auger electron spectroscopy (AES) results revealed that besides the Al micromasking effect, the carbon residue that formed a carbon-rich layer, could also play a significant role in affecting the surface roughness. Based on the AES results, an alternative explanation on the origin of the coarse surface is proposed.

Reactive Ion Etching of TaSix in a CF4-O2 Discharge

1991 ◽  
Vol 240 ◽  
Author(s):  
C. P. Chen ◽  
K. S. Din ◽  
F. S. Huang
Keyword(s):  
Total Pressure ◽  
Etch Rate ◽  
Gas Flow ◽  
Reactive Ion Etching ◽  
Rf Power ◽  
Ion Etching ◽  
Gaas Mesfet ◽  
Maximum Value ◽  
Oxygen Percentage ◽  
Sem Micrograph

ABSTRACTIn the self-alignment technology for GaAs MESFET, the pattern technique for refractory suicide gate is needed. Reactive ion etching (RIE) of TaSix on GaAs has been performed in a mixture of CF4 and O2 Etching properties have been studied as function of oxygen percentage, total pressure and power. The samples were then examined in Scanning electron microscopy (SEM) and Auger electron spectroscopy (AES) to understand the surface morphology and constitution. It is found that the etch rate of TaSixincreased with increasing oxygen percentage initially, reached a maximum value near 10∼15% O2, then started to decrease with increasing oxygen at applied power 100 watt, pressure 50 mtorr, and total gas flow 40 seem. This etch rate also increases with RF power and total pressure in CF4 + O2 15% gas at gas flow rate 40 sccm. For GaAs etching, the rate is independent of oxygen percentage. This etch rate of GaAs also increases with power, but decreases with total pressure. Meanwhile, the SEM micrograph shows no undercut for sample after RIE at the applied power 140 watt with the pressure of 20 mtorr.

Interaction Relationship Analysis of Surface Roughness on Aluminium Etched Wafer Using RIE

2014 ◽  
Vol 487 ◽  
pp. 214-217
Author(s):  
Zaliman Sauli ◽  
Vithyacharan Retnasamy ◽  
Aaron Koay Terr Yeow ◽  
Ng Wei Wei
Keyword(s):  
Surface Roughness ◽  
Factorial Design ◽  
Design Of Experiment ◽  
Reactive Ion Etching ◽  
Full Factorial Design ◽  
Strong Interactions ◽  
Rf Power ◽  
Ion Etching ◽  
Relationship Analysis ◽  
Full Factorial

This paper presents the interaction relationships between Tetrafluoromethane (CF4) gas, Oxygen (O2) gas, and RF power in response to the surface roughness of an Aluminium deposited wafer after being etched using Reactive Ion Etching (RIE). The investigation was done using the three factors full factorial design of experiment (DOE). Analysis was done qualitatively by plotting the main interaction plots. The results suggest that strong interactions are present between CF4 and RF power, CF4 and O2, and also O2 and RF power due to the intersection of the graphs. This implies that all three factors have interaction between each other towards the surface roughness on the deposited Aluminium after RIE.

Study on Reactive Ion Etching of Vanadium Oxide Thin Film by Taguchi Method

2014 ◽  
Vol 909 ◽  
pp. 91-94
Author(s):  
Jun Gou ◽  
Hui Ling Tai ◽  
Jun Wang ◽  
De En Gu ◽  
Xiong Bang Wei ◽  
...  
Keyword(s):  
Thin Film ◽  
Taguchi Method ◽  
Vanadium Oxide ◽  
Etch Rate ◽  
Reactive Ion Etching ◽  
Oxide Thin Film ◽  
Optimum Process ◽  
Rf Power ◽  
Ion Etching ◽  
Vanadium Oxide Thin Film

A high selectivity patterning technology of vanadium oxide (VOx) thin film was suggested in this paper. VOxthin film was etched through a photoresist (PR) mask using Cl/N based gases in a reactive ion etching (RIE) system. Taguchi method was used for process design to identify factors that influence the patterning and find optimum process parameters. Experimental results suggested that RF power was the largest contribution factor for VOxetch rate, PR selectivity and uniformity on 6 inch diameter wafer. Uniformity and PR selectivity were improved by introducing a small amount of N2. High resolution and low roughness patterning transfer was achieved with a non uniformity of 2.4 %, an VOxetch rate of 74 nm/min, a PR selectivity of 0.96, a Si3N4selectivity of 5 and a SiO2selectivity of 10.

The effect of BCl3 pretreatment on the etching of AlN in Cl2-based plasma

2008 ◽  
Vol 1108 ◽  
Author(s):  
Xiaoyan Xu ◽  
Vladimir Kuryatkov ◽  
Boris Borisov ◽  
Mahesh Pandikunta ◽  
Sergey A Nikishin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Plasma Etching ◽  
Inductively Coupled Plasma ◽  
Etch Rate ◽  
Reactive Ion Etching ◽  
Native Oxide ◽  
Short Exposure ◽  
Ion Etching ◽  
Inductively Coupled ◽  
High Etch Rate

AbstractThe effect of BCl3 and BCl3/Ar pretreatment on Cl2/Ar and Cl2/Ar/BCl3 dry etching of AlN is investigated using inductively coupled plasma reactive ion etching. The native AlN oxide can be effectively removed by a short exposure to BCl3 or BCl3/Ar plasma. Compared to the chlorine based plasma etching, BCl3/Ar is found to have the highest etch rate for both AlN and its native oxide. Following removal of the native oxide, Cl2/Ar/BCl3 plasma etching with 15% BCl3 fraction results in a high etch rate ˜ 87 nm/min and modest increases in the surface roughness.

Low Damage Magnetron Reactive Ion Etching of GaAs

1991 ◽  
Vol 240 ◽  
Author(s):  
G. Mclane ◽  
M. Meyyappan ◽  
M. W. Cole ◽  
H. S. Lee ◽  
R. Lareau ◽  
...  
Keyword(s):  
Minimal Surface ◽  
Reactive Ion Etching ◽  
Surface Region ◽  
Surface Damage ◽  
Silicon Tetrachloride ◽  
Attractive Alternative ◽  
Ion Etching

ABSTRACTMagnetron reactive ion etching is an attractive alternative to reactive ion etching since it has the potential for producing minimal surface damage while still retaining the advantages of reactive ion etching. We report here the results of a study of GaAs magnetron ion etching using Freon-12 and silicon tetrachloride etch gases. Differences are found in etch profiles and surface region characteristics of GaAs samples etched by the two gases. The relevant mechanisms are discussed.

Reactive ion Etching of PbZrxTi1−xO3 and Ruo2 Tein Films

1993 ◽  
Vol 310 ◽  
Author(s):  
Dilip P. Vijay ◽  
Seshu B. Desu ◽  
Wei Pan
Keyword(s):  
Thin Films ◽  
Solid Solution ◽  
Etch Rate ◽  
Reactive Ion Etching ◽  
Gas Pressure ◽  
Limiting Factor ◽  
Rf Power ◽  
Ion Etching ◽  
Pzt Thin Films ◽  
Etch Rates

AbstractIn this work, we have identified a suitable etch gas (CCI2,F2 ) for Reactive Ion Etching (RIE) of PZT thin films on RuO2 electrodes. The etch rate and anisotropy have been studied as a function of etching conditions. The effect of gas pressure, RF power and O2 concentration on the etch rate have been determined. It was found that ion bombardment effects are primarily responsible for the etching of both PZT and RuO2 thin films. Etch rates of the order of 20-30 nm/min were obtained for PZT thin films under low gas pressure and high RF power conditions. The etch residues and the relative etch rates of the components of the PZT solid solution were determined using XPS. The results show that the etching of PbO is the limiting factor in the etch process. For RuO2 thin films, etch rates of the order of 8-10 nm/min were obtained when O2 was added to the etch gas.

scholarly journals A Comparative Study on the Effects of Passivation Methods on the Carrier Lifetime of RIE and MACE Silicon Micropillars

2019 ◽  
Vol 9 (9) ◽  
pp. 1804
Author(s):  
Amal Kabalan
Keyword(s):  
Comparative Study ◽  
Surface Treatment ◽  
Chemical Etching ◽  
Carrier Lifetime ◽  
Surface Passivation ◽  
Reactive Ion Etching ◽  
Surface Damage ◽  
Ion Etching ◽  
Metal Assisted Chemical Etching

Silicon micropillars have been suggested as one of the techniques for improving the efficiency of devices. Fabrication of micropillars has been done in several ways—Metal Assisted Chemical Etching (MACE) and Reactive Ion Etching (RIE) being the most popular techniques. These techniques include etching through the surface which results in surface damage that affects the carrier lifetime. This paper presents a study that compares the carrier lifetime of micropillars fabricated using RIE and MACE methods. It also looks at increasing carrier lifetime by surface treatment using three main approaches: surface passivation by depositing Al2O3, surface passivation by depositing SiO2/SiN, and surface passivation by etching using KOH and Hydrofluoric Nitric Acetic (HNA) solution. It was concluded that passivating with SiO2 and SiN results in the highest carrier lifetime on the MACE and RIE pillars.

Sign in / Sign up

Export Citation Format

Share Document