Fine-Grained Structures Associated with Deformation Twin and Its Influence on Tensile Behaviours in a Cold-Rolled Fe-Ni Alloy

2006 ◽  
Vol 503-504 ◽  
pp. 895-900 ◽  
Author(s):  
Tatsuya Morikawa ◽  
Taku Moronaga ◽  
Kenji Higashida
Keyword(s):  
Deformation Twin ◽  
Liquid Nitrogen Temperature ◽  
Invar Alloy ◽  
High Yield ◽  
Fine Grained ◽  
Transmission Electron ◽  
Ni Alloy ◽  
Cold Rolled ◽  
Crystallographic Planes

Fine-grained structures in Fe-36mass%Ni Invar alloy have been investigated by using transmission electron microscopy (TEM). Particular attention has been paid on the role of deformation twinning in the formation of fine-grained structures and its influence on tensile stressstrain behaviours of rolled specimens. In Fe-Ni Invar alloy with a moderate stacking fault energy, deformation twin did not appear in usual cold-rolling at room temperature (RT), where a kind of cell walls was formed and the Cu-type texture was observed. On the other hand, twinning was occurred by rolling when specimens were cooled to liquid nitrogen temperature (LNT) immediately before the rolling. In such case, a fine lamellar structure was developed and the brass-type texture appeared. However, the lamella boundaries did not coincide with any crystallographic planes, and they were intersected with the bands of deformation twin. Specimens rolled by 90% in thickness reduction exhibited tensile stressstrain behaviours similar to those observed in specimens with SPD structures. In particular, specimens rolled at LNT showed high yield strengths and non-uniform deformation.

scholarly journals In Situ IR Characterization of CO Interacting with Rh Nanoparticles Obtained by Calcination and Reduction of Hydrotalcite-Type Precursors

2011 ◽  
Vol 2011 ◽  
pp. 1-8 ◽  
Author(s):  
F. Basile ◽  
I. Bersani ◽  
P. Del Gallo ◽  
S. Fiorilli ◽  
G. Fornasari ◽  
...  
Keyword(s):  
Crystal Size ◽  
Liquid Nitrogen Temperature ◽  
Transmission Electron ◽  
In Situ Ir ◽  
Ft Ir ◽  
Co Disproportionation ◽  
Ft Ir Spectroscopy

Supported Rh nanoparticles obtained by reduction in hydrogen of severely calcined Rh/Mg/Al hydrotalcite-type (HT) phases have been characterized by FT-IR spectroscopy of adsorbed CO [both at room temperature (r.t.) and nominal liquid nitrogen temperature] and Transmission Electron Microscopy (TEM). The effect of reducing temperature has been investigated, showing that Rh crystal size increases from 1.4 nm to 1.8 nm when the reduction temperature increases from 750°C to 950°C. The crystal growth favours the formation of bridged CO species and linear monocarbonyl species with respect to gem-dicarbonyl species; when CO adsorbs at r.t., CO disproportionation occurs on Rh and it accompanies the formation of RhI(CO)2. The role of interlayer anions in the HT precursors to affect the properties of the final materials has been also investigated considering samples prepared from silicate-instead of carbonate-containing precursors. In this case, formation of RhI(CO)2 and CO disproportionation do not occur, and this evidence is discussed in terms of support effect.

Role of Vacancies and Solute Atoms on Grain Boundary Sliding

1999 ◽  
Vol 601 ◽  
Author(s):  
J.S. Vetrano ◽  
C.H. Henager ◽  
E.P. Simonen
Keyword(s):  
Grain Boundary ◽  
Solute Atom ◽  
Vacancy Concentration ◽  
Grain Boundary Sliding ◽  
Fine Grained ◽  
Grain Boundary Plane ◽  
Transmission Electron ◽  
Boundary Sliding ◽  
Solute Atoms

AbstractIt is necessary for grain boundary dislocations to slide and climb during the grain boundary sliding process that dominates fine-grained superplastic deformation. The process of climb requires either an influx of vacancies to the grain boundary plane or a local generation of vacancies. Transmission electron microscopy (TEM) observations of grain boundaries in superplastically deformed Al-Mg-Mn alloys quenched under load from the deformation temperature have revealed the presence of nano-scale cavities resulting from a localized supersaturation of vacancies at the grain boundary. Compositional measurements along interfaces have also shown an effect of solute atoms on the local structure. This is shown to result from a coupling of vacancy and solute atom flows during deformation and quenching. Calculations of the localized vacancy concentration indicate that the supersaturation along the grain boundary can be as much as a factor often. The effects of the local supersaturation and solute atom movement on deformation rates and cavity nucleation and growth will be discussed.

Synthesis and characterization of sol-gel derived lanthanum hexaluminate powders and films

1995 ◽  
Vol 10 (1) ◽  
pp. 71-76 ◽  
Author(s):  
Michael K. Cinibulk
Keyword(s):  
Thin Films ◽  
Solid State ◽  
Sol Gel ◽  
High Yield ◽  
Trace Impurities ◽  
Fine Grained ◽  
Oxide Powders ◽  
Solid State Kinetics ◽  
Transmission Electron ◽  
Kinetics Of Formation

Powders and thin films of high-yield lanthanum hexaluminate (LaAl11O18) were prepared by a sol-gel route and compared with yields obtained by conventional hot-pressing of oxide powders. X-ray diffraction and transmission electron microscopy (TEM) were used to characterize powders and thin films deposited on TEM grids. While the solid-state kinetics of formation of LaA11O18 are known to be extremely sluggish, the yield of LaAl11O18 formed by the sol-gel route was much higher than that obtained by processing under similar conditions by solid-state reaction of elemental oxides. The development of a very fine grained microstructure at 1200 °C and a coarser, much more mature microstructure at 1450 °C, with strong texturing of the magnetoplumbite phase, was observed by TEM. Isolated grains of LaAlO3 were present in all powders and films. Trace impurities, introduced most likely as impurities in the initial alumina sol, appear to have segregated to both the grain boundaries and to the external surfaces of grains in as-prepared films.

Ultra-Fine Grained Fe-32%Ni Alloy Processed by Multi-Axial Forging

2010 ◽  
Vol 97-101 ◽  
pp. 187-190 ◽  
Author(s):  
Bao Jun Han
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Microstructure Evolution ◽  
Strain Path ◽  
Internal Stresses ◽  
Deformation Bands ◽  
Fine Grained ◽  
Transmission Electron ◽  
Ni Alloy ◽  
Equiaxed Grains

The Fe-32%Ni alloy was multi-axially forged at the temperature of 873K and strain rate of 10-2s-1, then the microstructure evolution in Fe-32%Ni alloy during deformation was investigated by the transmission electron microscopy (TEM). The results show that the grain size decreases with strain. The severe plastic deformed microstructure is characterized by the ultra-fine equiaxed grains and high internal stresses. The microstructure evolution mechanism is presented as the following: firstly, the dislocations accumulate as deformation bands in some directions with the progress of deformation; then the cellular structured subgrains are formed by continuous intersecting of deformation bands for the changing of strain path; eventually, the ultra-fine structured grains are formed by the subgrains rotation and the dislocations rearrangement.

Submicron/nano Grained Stainless Steel with Superior Mechanical Properties

2005 ◽  
Vol 903 ◽  
Author(s):  
Shreyas Rajasekhara ◽  
M. C. Somani ◽  
M. Koljonen ◽  
L. P. Karjalainen ◽  
A. Kyröläinen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
Austenitic Stainless Steels ◽  
Tensile Tests ◽  
Total Elongation ◽  
Fine Grained ◽  
Grain Sizes ◽  
Transmission Electron ◽  
Superior Mechanical Properties ◽  
Cold Rolled

AbstractMetastable austenitic stainless steels may transform to martensite when subjected to cold rolling. Upon subsequent annealing the martensite reverts back to ultra-fine grained austenite. Based on this concept, nano/submicron austenitic grains have been produced in a 63% cold rolled commercial AISI 301LN subjected to annealing treatments at 600°C, 800°C and 1000°C for 1, 10 and 100 seconds.Transmission Electron Microscopy (TEM) observations show the formation of equiaxed austenitic grains as small as ∼ 200nm in samples annealed at 800°C, and a dramatic increase in grain size as the annealing temperature and duration is increased. Additional tensile tests indicate that samples annealed at 800°C for 1 second exhibit a yield strength of ∼ 740 MPa and an total elongation of ∼ 45%. This combination of strength and ductility is excellent exceeding those of conventionally annealed steels (σy=350 MPa; Ductility ∼ 40%) or cold-rolled steels (σy=650 MPa; Ductility ∼ 30%).Finally, a correlation between the observed grain sizes and mechanical properties, in particular the yield strength, is obtained. Preliminary analysis indicates that the Hall-Petch equation can satisfactorily relate the observed yield strength with corresponding grain sizes.

On Future Directions in Pathology

1982 ◽  
Vol 40 ◽  
pp. 274-277
Author(s):  
Benjamin F. Trump ◽  
Irene K. Berezesky ◽  
Raymond T. Jones
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Clinical Pathology ◽  
Future Directions ◽  
Diagnostic Pathology ◽  
The Past ◽  
Transmission Electron ◽  
Organ Systems ◽  
The Many

The role of electron microscopy and associated techniques is assured in diagnostic pathology. At the present time, most of the progress has been made on tissues examined by transmission electron microscopy (TEM) and correlated with light microscopy (LM) and by cytochemistry using both plastic and paraffin-embedded materials. As mentioned elsewhere in this symposium, this has revolutionized many fields of pathology including diagnostic, anatomic and clinical pathology. It began with the kidney; however, it has now been extended to most other organ systems and to tumor diagnosis in general. The results of the past few years tend to indicate the future directions and needs of this expanding field. Now, in addition to routine EM, pathologists have access to the many newly developed methods and instruments mentioned below which should aid considerably not only in diagnostic pathology but in investigative pathology as well.

Strain-induced martensite effects on transgranular carbide precipitation in type 304 stainless steels

1991 ◽  
Vol 49 ◽  
pp. 604-605
Author(s):  
A.H. Advani ◽  
L.E. Murr ◽  
D. Matlock
Keyword(s):  
Heat Treatment ◽  
Grain Boundary ◽  
Stress Corrosion Cracking ◽  
Stainless Steels ◽  
Deformation Twin ◽  
Austenitic Stainless Steels ◽  
Carbide Precipitation ◽  
Strain Induced Martensite ◽  
Type 304

Thermomechanically induced strain is a key variable producing accelerated carbide precipitation, sensitization and stress corrosion cracking in austenitic stainless steels (SS). Recent work has indicated that higher levels of strain (above 20%) also produce transgranular (TG) carbide precipitation and corrosion simultaneous with the grain boundary phenomenon in 316 SS. Transgranular precipitates were noted to form primarily on deformation twin-fault planes and their intersections in 316 SS.Briant has indicated that TG precipitation in 316 SS is significantly different from 304 SS due to the formation of strain-induced martensite on 304 SS, though an understanding of the role of martensite on the process has not been developed. This study is concerned with evaluating the effects of strain and strain-induced martensite on TG carbide precipitation in 304 SS. The study was performed on samples of a 0.051%C-304 SS deformed to 33% followed by heat treatment at 670°C for 1 h.

Transmission Electron Microscopy studies of texture of Cr underlayer of magnetic recording hard disk

1991 ◽  
Vol 49 ◽  
pp. 580-581
Author(s):  
L. Tang ◽  
G. Thomas ◽  
M. R. Khan ◽  
S. L. Duan
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Magnetic Recording ◽  
Magnetic Thin Films ◽  
Magnetic Films ◽  
Substrate Bias ◽  
Epitaxial Relationship ◽  
Transmission Electron

Cr thin films are often used as underlayers for Co alloy magnetic thin films, such as Co1, CoNi2, and CoNiCr3, for high density longitudinal magnetic recording. It is belived that the role of the Cr underlayer is to control the growth and texture of the Co alloy magnetic thin films, and, then, to increase the in plane coercivity of the films. Although many epitaxial relationship between the Cr underlayer and the magnetic films, such as ﹛1010﹜Co/ {110﹜Cr4, ﹛2110﹜Co/ ﹛001﹜Cr5, ﹛0002﹜Co/﹛110﹜Cr6, have been suggested and appear to be related to the Cr thickness, the texture of the Cr underlayer itself is still not understood very well. In this study, the texture of a 2000 Å thick Cr underlayer on Nip/Al substrate for thin films of (Co75Ni25)1-xTix dc-sputtered with - 200 V substrate bias is investigated by electron microscopy.

Sign in / Sign up

Export Citation Format

Share Document