Exfoliation and Fracture Behavior of Oxide Films Formed on Titanium and Its Alloy in High Temperature Environments

2006 ◽  
Vol 522-523 ◽  
pp. 417-424 ◽  
Author(s):  
Yoshinori Isomoto Oka ◽  
Takahiro Yamabe ◽  
Toshinori Tsumura
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
High Temperature ◽  
Oxide Film ◽  
Oxide Films ◽  
Pure Titanium ◽  
Specimen Surface ◽  
Wide Range ◽  
Basic Behavior ◽  
Corrosive Environments

It is very difficult to obtain mechanical properties of oxide films formed on a material in high temperature environments despite its importance of estimating material degradation caused by such as thermal stress. Corrosion/oxidation tests were conducted for pure titanium and titanium alloy in high temperature corrosive environments of wet air and water vapor with hydrogen chloride at temperatures from 673 K to 973 K to look into basic behavior of degradation and the growth of titanium oxide films. It was found that oxide films were usually formed on the specimen surface and the growth was accelerated by the corrosiveness of the environment. In order to examine mechanical properties and exfoliation of corrosion products or oxide films formed on titanium and its alloy, tests of single particle impact on the specimen surface with a glass bead were performed in high temperature corrosive environments. The piling-up surfaces around impact craters were formed and plastically strained. The oxide film formed on the metal surface was detached in a wide range of the circumference and fractured a little far from the rim of the crater. Then fracture and exfoliation stress of the oxide film were estimated by the calculation of impact energy and fractured and detached areas. It was found that both the fracture and exfoliation stress of the oxide films were different depending on the corrosive environment and chemical composition of titanium alloy.

scholarly journals Mechanical Properties and Adhesion of Oxide Films Formed on Pure Titanium at High Temperature Corrosive Environments

2006 ◽  
Vol 55 (1) ◽  
pp. 25-31 ◽  
Author(s):  
Yoshinori Isomoto ◽  
Takahiro Yamabe ◽  
Toki Yoshida ◽  
Toshinori Tsumura
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Oxide Films ◽  
Pure Titanium ◽  
Corrosive Environments

Application of TEM to Deformation, Wear, and Fracture of Ceramics

1974 ◽  
Vol 32 ◽  
pp. 472-473
Author(s):  
B. J. Hockey
Keyword(s):  
Wear Resistance ◽  
High Temperature ◽  
Mechanical Behavior ◽  
Brittle Materials ◽  
High Temperature Strength ◽  
Wide Range ◽  
Corrosive Environments ◽  
Further Development

Ceramics, such as Al2O3 and SiC have numerous current and potential uses in applications where high temperature strength, hardness, and wear resistance are required often in corrosive environments. These materials are, however, highly anisotropic and brittle, so that their mechanical behavior is often unpredictable. The further development of these materials will require a better understanding of the basic mechanisms controlling deformation, wear, and fracture.The purpose of this talk is to describe applications of TEM to the study of the deformation, wear, and fracture of Al2O3. Similar studies are currently being conducted on SiC and the techniques involved should be applicable to a wide range of hard, brittle materials.

Oxidation Effects during High Temperature Deformation of CP Ti Alloy

2007 ◽  
Vol 539-543 ◽  
pp. 3678-3683
Author(s):  
Ming Jen Tan ◽  
X.J. Zhu ◽  
S. Thiruvarudchelvan ◽  
K.M. Liew
Keyword(s):  
High Temperature ◽  
Oxide Film ◽  
High Temperatures ◽  
Pure Titanium ◽  
Initial Strain Rate ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Uniaxial Tensile ◽  
Commercially Pure Titanium ◽  
Commercially Pure

This work reports the influence of oxidation on the superplasticity of commercially pure titanium at high temperatures. Uniaxial tensile tests were conducted at temperatures in the range 600-800°C with an initial strain rate of 10s-1 to 10s-3. This study shows that oxidization at the surface of the alloy causes oxide film on the surface of commercially pure titanium alloy, and the thickness of oxide film increase with increasing exposure time and temperature. XRD analysis shows that the oxide film consists of TiO2. Because this oxide film is very brittle, it can induce clefts and degrade the ductility of the titanium at high temperatures. The mechanism of the initial clefts was investigated and a model for the cleft initiation and propagation during high temperature tensile test was proposed.

Influences of Solution Temperatures on Microstructure and Mechanical Properties of near α Titanium Alloy

2021 ◽  
Vol 1035 ◽  
pp. 89-95
Author(s):  
Chao Tan ◽  
Zi Yong Chen ◽  
Zhi Lei Xiang ◽  
Xiao Zhao Ma ◽  
Zi An Yang
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
High Temperature ◽  
Room Temperature ◽  
Solution Temperature ◽  
Vacuum Induction Melting ◽  
Induction Melting ◽  
Β Phase ◽  
Α Phase ◽  
New Type

A new type of Ti-Al-Sn-Zr-Mo-Si series high temperature titanium alloy was prepared by a water-cooled copper crucible vacuum induction melting method, and its phase transition point was determined by differential thermal analysis to be Tβ = 1017 °C. The influences of solution temperature on the microstructures and mechanical properties of the as-forged high temperature titanium alloy were studied. XRD results illustrated that the phase composition of the alloy after different heat treatments was mainly α phase and β phase. The microstructures showed that with the increase of the solution temperature, the content of the primary α phase gradually reduced, the β transformation structure increased by degrees, then, the number and size of secondary α phase increased obviously. The tensile results at room temperature (RT) illustrated that as the solution temperature increased, the strength of the alloy gradually increased, and the plasticity decreased slightly. The results of tensile test at 650 °C illustrated that the strength of the alloy enhanced with the increase of solution temperature, the plasticity decreased first and then increased, when the solution temperature increased to 1000 °C, the alloy had the best comprehensive mechanical properties, the tensile strength reached 714.01 MPa and the elongation was 8.48 %. Based on the room temperature and high temperature properties of the alloy, the best heat treatment process is finally determined as: 1000 °C/1 h/AC+650 °C/6 h/AC.

Effect of Hot Processing on Mircrostructure and Properties of Flat Billets of TA15 Titanium Alloy

2021 ◽  
Vol 1016 ◽  
pp. 906-910
Author(s):  
Xin Hua Min ◽  
Cheng Jin
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Titanium Alloy ◽  
High Temperature ◽  
Room Temperature ◽  
High Strength ◽  
Slow Cooling ◽  
Microstructure And Mechanical Properties ◽  
Ta15 Titanium Alloy ◽  
The Ideal

In this paper,effect of the different forging processes on the microstructure and mechanical properties of the flat flat billets of TA15 titanium alloy was investigated.The flat billiets of 80 mm×150 mm×L sizes of TA15 titanium alloy are produced by four different forging processes.Then the different microstrure and properties of the flat billiets were obtained by heat treatment of 800 °C~850 °C×1 h~4h.The results show that, adopting the first forging temperature at T1 °C、slow cooling and the second forging temperature at T2°C 、quick cooling, the primary αphases content is just 10%, and there are lots of thin aciculate phases on the base. This microstructure has both high strength at room temperature and high temperature, while the properties between the cross and lengthwise directions are just the same. So the hot processing of the first forging temperature at T1 °C、slow cooling and the second forging temperature at T2°C 、quick cooling is choosed as the ideal processing for production of aircraft frame parts.

scholarly journals High-Temperature Flow Behaviour and Constitutive Equations for a TC17 Titanium Alloy

2019 ◽  
Vol 38 (2019) ◽  
pp. 168-177 ◽  
Author(s):  
Liu Shi-feng ◽  
Shi Jia-min ◽  
Yang Xiao-kang ◽  
Cai Jun ◽  
Wang Qing-juan
Keyword(s):  
Titanium Alloy ◽  
High Temperature ◽  
Constitutive Equation ◽  
Constitutive Equations ◽  
Deformation Behaviour ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Compression Tests ◽  
Average Absolute Relative Error ◽  
Wide Range

AbstractIn this study, the high-temperature deformation behaviour of a TC17 titanium alloy was investigated by isothermal hot compression tests in a wide range of temperatures (973–1223 K) and strain rates (0.001–10 s−1). Then, the constitutive equations of different phase regimes (α + β and single β phases) were developed on the basis of experimental stress-strain data. The influence of the strain has been incorporated in the constitutive equation by considering its effect on different material constants for the TC17 titanium alloy. Furthermore, the predictability of the developed constitutive equation was verified by the correlation coefficient and average absolute relative error. The results indicated that the obtained constitutive equations could predict the high-temperature flow stress of a TC17 titanium alloy with good correlation and generalization.

Identification of the Initial Oxide Films on 18-8 Stainless Steel in High Temperature Water

CORROSION ◽  
1968 ◽  
Vol 24 (10) ◽  
pp. 336-337 ◽  
Author(s):  
T. NAKAYAMA ◽  
Y. OSHIDA
Keyword(s):  
Stainless Steel ◽  
High Temperature ◽  
Oxide Film ◽  
Oxide Films ◽  
Spinel Type ◽  
High Temperature Water ◽  
Temperature Water

Abstract Initial oxide film formed on 18–8 stainless steel in high temperature water at 300 C (572 F) for 1 hour was identical with corundum type crystals like (Cr, Fe)2O3 alone or its coexistence with α-Fe2O3. On the contrary, the oxide film produced by prolonged oxidation (24 hours) consisted mainly of the spinel type crystals containing nickel.

Sign in / Sign up

Export Citation Format

Share Document