Heat-Resistant Al-Alloys with Quasicrystalline and L12- Precipitates

We have been developing Al-Mn-Cu based alloys alloyed with minor additions of different elements. Small additions of beryllium enhance the formation of the icosahedral quasicrystalline phase (IQC) during solidification, especially during ageing. Upon solidification, primary IQC-particles may form, with sizes, ranging from 5 to 50 μm. IQC is also present as a part of binary eutectic in the interdendritic regions. More importantly, nanosized quasicrystalline precipitates can form during T5-treatment at temperatures ranging from about 250−450 °C. They are, in fact, metastable precipitates transforming to ternary T-precipitates (Al20Mn3Cu2) phase above 450 °C. The heat resistance can be increased considerably by the addition of Sc and Zr by forming L12-precipitates in spaces between quasicrystalline precipitates. In this paper, we studied three alloys, two Al-Mn-Cu-Be alloys and an Al-Mn-Cu-Be-Sc-Zr alloy. The alloys were produced by vacuum induction melting and casting into a copper mould. We investigated the response of the alloys to different heat treatments and their heat resistance at higher temperatures. It was shown that the alloys could be precipitation strengthened by ageing at 300 °C and 400 °C. The hardness of the alloy stayed at relatively high levels even at 500 °C, while more substantial softening occurred at 600 °C.

Effect of Ta and W Additions on Microstructure and Mechanical Properties of Tilt-Cast Ti-45Al-5Nb-2C Alloy

The effect of Ta and W additions on microstructure and mechanical properties of tilt-cast Ti-45Al-5Nb-2C (at.%) alloy was investigated. Three alloys with nominal composition Ti-45Al-5Nb-2C-2X (in at.%), where X is Ta or W, were prepared by vacuum induction melting in graphite crucibles followed by tilt casting into graphite moulds. The microstructure of the tilt-cast alloys consists of the α2(Ti3Al) + γ(TiAl) lamellar grains, single γ phase, (Ti,Nb,X)2AlC particles with a small amount of (Ti,Nb,X)C, and β/B2 phase identified only in W containing alloy. The EDS analysis shows that Ta segregates into the carbide particles and reduces dissolution of Nb in both (Ti,Nb,Ta)C and (Ti,Nb,Ta)2AlC phases. The alloying with W reduces Nb content in both carbide phases and leads to stabilisation of β/B2 phase in the lamellar α2 + γ regions. The alloying with Ta and W does not affect the volume fraction of the carbide particles but influences their size and morphology. While the alloying with Ta and W has no significant effect on Vickers hardness and the indentation elastic modulus of the studied alloys, the addition of Ta affects the nanohardness and elastic modulus of the (Ti,Nb,Ta)2AlC phase. The addition of W significantly increases the Vickers microhardness of the lamellar α2 + γ regions.

X-ray Computed Tomography Studies on Porosity Distribution in Vacuum Induction Cast Al-7Si Alloys

Porosity in aluminum alloys is a great concern to the casting and automotive industry. In this publication, porosity formation in air-melted and vacuum induction melted (VIM) aluminum alloys was studied and compared to understand its effect on microstructure and mechanical properties of Al-7Si alloys. Al-7Si alloys were cast at 700°C and 900°C in a muffle furnace and VIM furnace. Microstructural results show that the alloys cast in muffle furnace refined the eutectic silicon compared with the cast samples prepared in VIM furnace. X-ray computed tomography (XCT) was used for three-dimensional (3D) visualization and quantification of porosity in these alloys. The volume fraction of pores was observed to be higher in alloy air-melted at 900°C compared with 700°C. XCT results from VIM alloy samples showed no significant porosity when cast at either 700°C or 900°C. The morphology of large pores in alloys air-melted at 700°C represents the formation of shrinkage porosity due to the incomplete flow of molten metal during solidification. Tensile test results show that the elongation property of VIM alloy was increased by more than 20% compared with air-melted alloy. The tensile strength and elongation were observed to be higher for alloy samples cast at 700°C compared with 900°C for both air-melted and VIM alloys. The findings from microstructure, XCT, and tensile tests show that vacuum induction melting improves the mechanical properties of the alloy compared with air-melted alloy.

The Effect of Zr Addition on Melting Temperature, Microstructure, Recrystallization and Mechanical Properties of a Cantor High Entropy Alloy

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its micro-structure, mechanical properties and thermomechanical recrystallization process. The base and Zr-modified alloys are obtained by vacuum induction melting of mechanically pre-alloyed powders. Raw materials are then cold rolled and annealed. recrystallization occurred during the heat treatment of the cold-rolled HEA. The alloys are characterized by X-ray diffraction, electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: (1) a fast vacuum induction melting process; (2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; (3) the good chemical alloy homogeneity; and (4) the mechanical properties improvement of re-crystallized grains with a coherent structure. The crystallographic lattice of both alloys results in FCC. The Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipitation of a coherent second phase, which enhances the alloy hardness and strength.

Quantitative Examination of the Inclusion and the Rotated Bending Fatigue Behavior of SAE52100

This study investigated the effect of maximum inclusion on the life of SAE52100 bearing steel processed by two different melting routes, vacuum induction melting plus electroslag remelting (VIM + ESR), and basic oxygen furnace plus ladle furnace plus vacuum degassing process (BOF + LF + RH) by the metallographic method, Aspex explorer, and rotated bending fatigue test. The rotated bending method was applied to examine the maximum inclusion size in a satisfactory manner, whereas both the metallographic method and Aspex explorer underestimated the result. Regardless of the characterization methods, the results show that the total number of inclusions in VIM + ESR melted steel is significantly higher than that in BOF + LF + RH processed steel, but the maximum inclusion size of VIM + ESR melted steel is significantly smaller than that of the BOF + LF + RH degassed steel. The distribution of the maximum inclusion size could be well fitted by the inverse Weibull distribution and could be well applied to reveal the different inclusion size distribution based on the data examined by the rotated bending fatigue method. Finally, a new equation was proposed to establish the relationship among the loading stress amplitude, rotated bending fatigue number, and the maximum inclusion size.

Low-Hysteresis Shape Memory Alloy Scale-Up: DSC, XRD and Microstructure Analysis on Heat-Treated Vacuum Induction Melted Ni-Ti-Cu-Pd Alloys

Quaternary Ni-Ti-Cu-Pd formulations were cast by vacuum induction melting (VIM) with the aim of preparing low-hysteresis shape memory alloys and verifying the applicability of the Co-Factor theory in conventional industrial manufacturing processes. The cast alloys showed lower transformation hysteresis width in DSC measurements than binary Ni-Ti, but struggled to achieve a near zero hysteresis, as predicted by the theoretical framework, despite being close to satisfy the first Co-Factor condition (CC I) that foresees minimum hysteresis for formulations in which the middle eigenvalue of the martensitic transformation matrix λ2 approaches one. The microstructure of the annealed Ni-Ti-Cu-Pd alloys exhibited a considerable amount of mostly sub-micron-sized secondary phases, which distort the matrix composition and prevent it from reaching the optimum stoichiometry for satisfying the CC I. In addition, this class of materials is prone to aging effects, leading to the formation of semi-coherent tetragonal precipitates, which tend to also form at the grain boundaries after low-temperature annealing, further affecting the transformation hysteresis in DSC experiments depending on the thermal history. This work reveals the importance of considering typical casting effects that alter the theoretical λ2 of ideal materials in the compositional design for the development of high-performance low-hysteresis alloys.

The Effect of Zr Addition on Melting Temperature, Microstructure, Recrystallization and Mechanical Properties of a Cantor High Entropy Alloy

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

Behavior of Nitrogen in GH4169 Superalloy Melt during Vacuum Induction Melting Using Returned Materials

The nitrogen behavior of superalloy melt GH4169 during the vacuum induction melting (VIM) process was clarified by using different proportions of returned materials including block-shaped returned material, chip-shaped returned material, and pure materials to produce a high–purity superalloy melt and provide guidance for the purification of the superalloy melt. For the nitrogen removal during the VIM process, the denitrification rate in the refining period reached 10 ppm per hour on average, which is significantly higher than 1 ppm per hour on average in the melting period. The denitrification reaction of superalloy melt GH4169 under extremely low vacuum pressure is controlled by both the mass transfer of nitrogen in the melt and the chemical reaction of the liquid–gas interface. The nitrogen removal of superalloy melts during VIM occurs through the two methods of gasification denitrification and nitride floatation because the nitrides begin to precipitate in the liquid phase at 1550 °C. A higher nitrogen removal rate can be obtained by increasing the proportion of chip-shaped material or decreasing the proportion of block-shaped material.