Solute Partitioning to Enhance Mechanical Properties of Aged Aluminium Alloys

2009 ◽  
Vol 618-619 ◽  
pp. 487-491 ◽  
Author(s):  
Ian J. Polmear ◽  
Roger N. Lumley
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Fracture Toughness ◽  
Fatigue Strength ◽  
Aluminium Alloys ◽  
Creep Resistance ◽  
Fracture Properties ◽  
Secondary Precipitation ◽  
The Matrix

Deliberate partitioning of solute elements between the matrix solid solution and dispersed precipitates in aged aluminium alloys can be facilitated by underageing during heat treatment. Although this practice may cause some reduction in tensile properties, it has been shown that significant improvements may be achieved in creep resistance, fatigue strength and fracture toughness. Exploitation of secondary precipitation can allow simultaneous increases to be obtained in tensile and fracture properties.

Reinforced Pores in Porous Steels Obtained with Matrix Soluble Space Holders

MRS Advances ◽  
2019 ◽  
Vol 4 (54) ◽  
pp. 2959-2967
Author(s):  
G.O. Neves ◽  
G. Paz ◽  
N. Araya ◽  
C. Binder ◽  
A.N. Klein
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Fatigue Strength ◽  
Porous Materials ◽  
Crack Nucleation ◽  
Iron Matrix ◽  
Wide Range ◽  
The Matrix ◽  
Carbide Particles ◽  
Shape And Size

ABSTRACTThis paper presents a novel way to obtain reinforced pores by the dissociation of mixed carbides during sintering. Porous materials have a wide range of applications such as dampeners, light structures, etc. But usually pores act as points of stress concentration and crack nucleation, harming the mechanical properties of these materials. Methods have been developed to control the shape and size of pores but, until now, there are no techniques that allow reinforcing the material around the pores. To address this, steels were prepared by adding 1, 3 and 5 wt.% of Mo1.5Cr0.5C mixed carbide particles to a iron matrix by metal injection moulding. The results showed that during sintering, the dissociation of the carbide followed by the dissolution of the elements in the matrix generated rounded secondary pores with a reinforced vicinity, which increased the mechanical strength of the materials. The presence of rounded pores encircled by an enriched vicinity can allow the production of porous materials with exceptional fatigue strength and fracture toughness.

CARLSON ALLOY C600 and C600 ESR

Alloy Digest ◽  
1994 ◽  
Vol 43 (11) ◽  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Fracture Toughness ◽  
Cold Working ◽  
Elevated Temperatures ◽  
High Strength ◽  
Heat Treating ◽  
Solid Solution Alloy ◽  
Resistance To Oxidation ◽  
Good Workability

Abstract CARLSON ALLOYS C600 AND C600 ESR have excellent mechanical properties from sub-zero to elevated temperatures with excellent resistance to oxidation at high temperatures. It is a solid-solution alloy that can be hardened only by cold working. High strength at temperature is combined with good workability. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, and machining. Filing Code: Ni-470. Producer or source: G.O. Carlson Inc.

ALTEMP HX

Alloy Digest ◽  
1993 ◽  
Vol 42 (10) ◽  
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
Fracture Toughness ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Base Alloy ◽  
Heat Treating ◽  
Nickel Base Alloy ◽  
Temperature Performance ◽  
Nickel Base

Abstract ALTEMP HX is an austenitic nickel-base alloy designed for outstanding oxidation and strength at high temperatures. The alloy is solid-solution strengthened. Applications include uses in the aerospace, heat treatment and petrochemical markets. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness and creep. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, and joining. Filing Code: Ni-442. Producer or source: Allegheny Ludlum Corporation.

Mechanical properties of NiAl-Mo composites produced by specially controlled directional solidification

2012 ◽  
Vol 1516 ◽  
pp. 255-260 ◽  
Author(s):  
G. Zhang ◽  
L. Hu ◽  
W. Hu ◽  
G. Gottstein ◽  
S. Bogner ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Directional Solidification ◽  
Creep Resistance ◽  
Room Temperature ◽  
Growth Direction ◽  
Nominal Composition ◽  
Potential Candidate ◽  
In Situ Composites

ABSTRACTMo fiber reinforced NiAl in-situ composites with a nominal composition Ni-43.8Al-9.5Mo (at.%) were produced by specially controlled directional solidification (DS) using a laboratory-scale Bridgman furnace equipped with a liquid metal cooling (LMC) device. In these composites, single crystalline Mo fibers were precipitated out through eutectic reaction and aligned parallel to the growth direction of the ingot. Mechanical properties, i.e. the creep resistance at high temperatures (HT, between 900 °C and 1200 °C) and the fracture toughness at room temperature (RT) of in-situ NiAl-Mo composites, were characterized by tensile creep (along the growth direction) and flexure (four-point bending, vertical to the growth direction) tests, respectively. In the current study, a steady creep rate of 10-6s-1 at 1100 °C under an initial applied tensile stress of 150MPa was measured. The flexure tests sustained a fracture toughness of 14.5 MPa·m1/2at room temperature. Compared to binary NiAl and other NiAl alloys, these properties showed a remarkably improvement in creep resistance at HT and fracture toughness at RT that makes this composite a potential candidate material for structural application at the temperatures above 1000 °C. The mechanisms responsible for the improvement of the mechanical properties in NiAl-Mo in-situ composites were discussed based on the investigation results.

The Investigation on Aluminium Alloys Automobile Wheel with Low-Titanium Content Produced by Electrolysis

2005 ◽  
Vol 475-479 ◽  
pp. 317-320 ◽  
Author(s):  
Jing Pei Xie ◽  
Ji Wen Li ◽  
Zhong Xia Liu ◽  
Ai Qin Wang ◽  
Yong Gang Weng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminium Alloys ◽  
Solution Treatment ◽  
A356 Alloy ◽  
Aging Treatment ◽  
Titanium Content ◽  
The Matrix ◽  
Automobile Wheel

The in-situ Ti alloying of aluminium alloys was fulfilled by electrolysis, and the material was made into A356 alloy and used in automobile wheels. The results show that the grains of the A356 alloy was refined and the second dendrites arm was shortened due to the in-situ Ti alloying. Trough 3-hour solution treatment and 2-hour aging treatment for the A356 alloy, the microstructures were homogeneous, and Si particles were spheroid and distribute in the matrix fully. The outstanding mechanical properties with tensile strength (σb≥300Mpa) and elongation values (δ≥10%) have been obtained because the heat treatment was optimized. Compared with the traditional materials, tensile strength and elongation were increased by 7.6~14.1% and 7.4~44.3% respectively. The qualities of the automobile wheels were improved remarkably.

scholarly journals Effects of Different Solid Solution Temperatures on Microstructure and Mechanical Properties of the AA7075 Alloy After T6 Heat Treatment

2019 ◽  
Vol 38 (2019) ◽  
pp. 892-896 ◽  
Author(s):  
Süleyman Tekeli ◽  
Ijlal Simsek ◽  
Dogan Simsek ◽  
Dursun Ozyurek
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Tensile Strength ◽  
Tensile Tests ◽  
Solution Temperature ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Different Temperatures

AbstractIn this study, the effect of solid solution temperature on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment was investigated. Following solid solution at five different temperatures for 2 hours, the AA7075 alloy was quenched and then artificially aged at 120∘C for 24 hours. Hardness measurements, microstructure examinations (SEM+EDS, XRD) and tensile tests were carried out for the alloys. The results showed that the increased solid solution temperature led to formation of precipitates in the microstructures and thus caused higher hardness and tensile strength.

Crystallization behavior, Al-Ce intermetallic formation, and microstructure refinement of near-eutectic Al–Si alloys by rare-earth element additions

2020 ◽  
Vol 111 (11) ◽  
pp. 938-952
Author(s):  
Bo Chi ◽  
Zhiming Shi ◽  
Cunquan Wang ◽  
Liming Wang ◽  
Hao Lian ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Rare Earth ◽  
Rare Earth Element ◽  
Crystallization Behavior ◽  
Earth Element ◽  
Microstructural Refinement ◽  
Preferential Growth ◽  
Intermetallic Formation ◽  
The Matrix

Abstract Near-eutectic Al-Si alloys have low strength and high brittleness because of the presence of many eutectic b-Si flakes, needle-like Al-Fe-Si intermetallics, and coarse α-Al grains. This study disclosed the effects of cerium-rich RE (rare earth) element modification on orientation characters of crystals, formation of Al-Ce compounds, and microstructural refinement to improve the microstructure and mechanical properties of the alloys. The RE addition depressed preferential growth along the close-packed and/or sub-closepacked planes and promoted growth along the non-closepacked planes, in which La and other elements were dissolved into needle-like Al11Ce3 phase. When the temperature decreased, Al11Ce3 was preferentially crystallized from the melts and then devitrified by attaching to the surface of β-Al5FeSi needles. Moreover, many small Al11Ce3 particles were precipitated in the matrix and on the Si surface by a T6 heat treatment. Eutectic β-Si phases were constructed into discontinuous networks, short rods, and even particles by RE additions, which were further transformed into fine nodules following the T6 treatment. α-Al grains and primary β-Al5FeSi needles were simultaneously refined. The addition of 1.0 wt.% REs and subsequent T6 treatment yielded the highest tensile strength, elongation, and hardness of the alloy.

scholarly journals Effect of Ground Slag on Mechanical Properties of Concrete under Low Temperature

2021 ◽  
Vol 2109 (1) ◽  
pp. 012019
Author(s):  
Xuelian Yuan ◽  
Jie Hu
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Compressive Strength ◽  
Low Temperature ◽  
Cement Paste ◽  
High Volume ◽  
Hardened Cement ◽  
Micro Structure ◽  
Hardened Cement Paste ◽  
Fracture Properties

Abstract Through using cube resisting compression test, fracture properties and micro-structure, the mechanical properties of high volume ground slag concrete under low temperature are studied in this paper. The results show that low temperature can improve the compressive strength of high volume ground slag concrete. And strength increased with the decreased of temperature. Low temperature can also improve the fracture energy and fracture toughness. Not only can ground slag reduce the content of calcium hydroxide in hardened cement paste, but ground slag can improve the compactness of hardened cement paste, reduce porosity and improve the strength of the interface.

Sign in / Sign up

Export Citation Format

Share Document