Warm Hydroforming Process with Non-Uniform Heating for AZ31 Magnesium Alloy Tube

2010 ◽  
Vol 654-656 ◽  
pp. 739-742 ◽  
Author(s):  
Kenichi Manabe ◽  
Toshiji Morishima ◽  
Yu Ogawa ◽  
Kazuo Tada ◽  
Tsutomu Murai ◽  
...  
Keyword(s):  
Finite Element ◽  
Temperature Distribution ◽  
Magnesium Alloy ◽  
Tube Hydroforming ◽  
Az31 Magnesium Alloy ◽  
Fe Model ◽  
Uniform Heating ◽  
Forming Process ◽  
Alloy Tube ◽  
Warm Hydroforming

In this study, non-uniform heating approach in warm T-joint forming process is attempted for the AZ31 magnesium alloy tube. For this purpose, finite element simulation is performed to analyze the appropriate temperature distribution. The validity of the finite element(FE) model of T-joint tube hydroforming(THF) is verified by comparing the FE simulation and experimental results. Using this FE model, appropriate temperature distribution was suggested. In addition, it was showed that the wall thickness could be more uniform by optimizing the temperature condition.

125 Effect of Temperature Distribution in Warm Hydroforming of AZ31 Magnesium Alloy Tube

2009 ◽  
Vol 2009.17 (0) ◽  
pp. _125-1_-_125-2_
Author(s):  
Ken-ichi MANABE ◽  
Yu OGAWA ◽  
Kazuo TADA ◽  
Tsutomu MURAI ◽  
Humiaki NAKAGAWA
Keyword(s):  
Temperature Distribution ◽  
Magnesium Alloy ◽  
Az31 Magnesium Alloy ◽  
Effect Of Temperature ◽  
Alloy Tube ◽  
Warm Hydroforming

scholarly journals Qualitative Research of AZ31 Magnesium Alloy Aircraft Brackets Produced by a New Forging Method

2016 ◽  
Vol 61 (2) ◽  
pp. 1003-1008 ◽  
Author(s):  
A. Dziubińska ◽  
A. Gontarz ◽  
K. Dziedzic
Keyword(s):  
Qualitative Research ◽  
Finite Element ◽  
Magnesium Alloy ◽  
Numerical Results ◽  
Experimental Results ◽  
Az31 Magnesium Alloy ◽  
Forming Process ◽  
Closed Die Forging ◽  
Selection Of ◽  
Good Agreement

AbstractThe paper reports a selection of numerical and experimental results of a new closed-die forging method for producing AZ31 magnesium alloy aircraft brackets with one rib. The numerical modelling of the new forming process was performed by the finite element method.The distributions of stresses, strains, temperature and forces were examined. The numerical results confirmed that the forgings produced by the new forming method are correct. For this reason, the new forming process was verified experimentally. The experimental results showed good agreement with the numerical results. The produced forgings of AZ31 magnesium alloy aircraft brackets with one rib were then subjected to qualitative tests.

scholarly journals Warm Hydroforming Process under Non-Uniform Temperature Field for Magnesium Alloy Tubes

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 901
Author(s):  
Toshiji Morishima ◽  
Ken-Ichi Manabe
Keyword(s):  
Temperature Distribution ◽  
Magnesium Alloy ◽  
Thickness Distribution ◽  
Tube Hydroforming ◽  
Fuzzy Model ◽  
Fe Analysis ◽  
Experimental Result ◽  
Loading Path ◽  
Analysis Model ◽  
Warm Hydroforming

The warm tube hydroforming (WTHF) process of lightweight materials such as magnesium alloy contributes to a remarkable weight reduction. The success of the WTHF process strongly depends on the loading path with internal pressure and axial feeding and other process variables including temperature distribution. Optimization of these process parameters in this special forming technique is a great issue to be resolved. In this study, the optimization of the symmetrical temperature distribution and process loading path for the warm T-shape forming of magnesium alloy AZ31B tube was carried out by finite element (FE) analysis using a fuzzy model. As a result, a satisfactory good agreement of the wall thickness distribution of the samples formed under the optimum loading path condition can be obtained between the FE analysis result and the experimental result. Based on the validity validation of FE analysis model, the optimization method was applied to other materials and forming shapes, and applicability was discussed.

Numerical Simulation of Microstructure Evolution in AZ31 Magnesium Alloy during Equal Channel Angular Pressing

2014 ◽  
Vol 609-610 ◽  
pp. 495-499
Author(s):  
Guo Cheng Ren ◽  
Xiao Juan Lin ◽  
Shu Bo Xu
Keyword(s):  
Finite Element ◽  
Magnesium Alloy ◽  
Equal Channel Angular Pressing ◽  
Microstructure Evolution ◽  
Element Model ◽  
Az31 Magnesium Alloy ◽  
Angular Pressing ◽  
Ecap Process ◽  
Element Simulation ◽  
3D Software

The microstructure and material properties of AZ31 magnesium alloy are very sensitive to process parameters, which directly determine the service properties. To explore and understand the deformation behavior and the optimization of the deformation process, the microstructure evolution during equal channel angular pressing was predicted by using the DEFORM-3D software package at different temperature. To verify the finite element simulation results, the microstructure across the transverse direction of the billet was measured. The results show that the effects strain and deformation temperatures on the microstructure evolution of AZ31 magnesium during ECAP process are significant, and a good agreement between the predicted and experimental results was obtained, which confirmed that the derived dynamic recrystallization mathematical models can be successfully incorporated into the finite element model to predict the microstructure evolution of ECAP process for AZ31 magnesium.

Finite Element Simulation and Experimental Study on Blow Forming of Plastic Cups

2011 ◽  
Vol 148-149 ◽  
pp. 1319-1322
Author(s):  
Xiao Hu ◽  
Yi Sheng Zhang ◽  
Hong Qing Li ◽  
De Qun Li
Keyword(s):  
Finite Element ◽  
Thickness Distribution ◽  
Viscoelastic Model ◽  
Engineering Practice ◽  
Fe Model ◽  
Thin Wall ◽  
Forming Process ◽  
Element Simulation ◽  
Physically Based ◽  
Set Up

Blow forming process of plastic sheets is simple and easy to realize, thus, it is widely used for plastic thin-wall parts. In the practical production, an effective method is needed for the preliminary set-up of process parameters in order to achieve accurate control of thickness distribution. Thus, a finite element method (FEM) code is used to simulate blow forming process. For better description of complex material theological characteristics, a physically based viscoelastic model (VUMAT forms Buckley model) to model the complex constitutive behavior is used. Nonlinear FE analyses using ABAQUS were carried out to simulate the blow forming process of plastic cups. The actual values at different locations show a satisfactory agreement with the simulation results: as a matter of fact the error along the cell mid-section did not exceed 0.02 mm on average, corresponding to 5% of the initial thickness, thus the FE model this paper can meet the requirements of the engineering practice.

scholarly journals Thermo-Fluid-Dynamic Modeling of the Melt Pool during Selective Laser Melting for AZ91D Magnesium Alloy

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4157
Author(s):  
Hongyao Shen ◽  
Jinwen Yan ◽  
Xiaomiao Niu
Keyword(s):  
Temperature Distribution ◽  
Magnesium Alloy ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Large Temperature ◽  
Fe Model ◽  
Laser Melting ◽  
Az91d Magnesium Alloy ◽  
Melt Pool ◽  
Flow Activity

A three dimensional finite element model (FEM) was established to simulate the temperature distribution, flow activity, and deformation of the melt pool of selective laser melting (SLM) AZ91D magnesium alloy powder. The latent heat in phase transition, Marangoni effect, and the movement of laser beam power with a Gaussian energy distribution were taken into account. The influence of the applied linear laser power on temperature distribution, flow field, and the melt-pool dimensions and shape, as well as resultant densification activity, was investigated and is discussed in this paper. Large temperature gradients and high cooling rates were observed during the process. A violent flow occurred in the melt pool, and the divergent flow makes the melt pool wider and longer but shallower. With the increase of laser power, the melt pool’s size increases, but the shape becomes longer and narrower. The width of the melt pool in single-scan experiment is acquired, which is in good agreement with the results predicted by the simulation (with error of 1.49%). This FE model provides an intuitive understanding of the complex physical phenomena that occur during SLM process of AZ91D magnesium alloy. It can help to select the optimal parameters to improve the quality of final parts and reduce the cost of experimental research.

Finite Element Simulation of Vacuum Hot Bulge Forming of Titanium Alloy Cylindrical Workpiece

2011 ◽  
Vol 675-677 ◽  
pp. 921-924 ◽  
Author(s):  
Ming Wei Wang ◽  
Chun Yan Wang ◽  
Li Wen Zhang
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Titanium Alloy ◽  
Finite Element Simulation ◽  
Process Parameters ◽  
Fe Model ◽  
Analysis Software ◽  
Forming Process ◽  
Element Simulation ◽  
Cylindrical Workpiece

Vacuum hot bulge forming (VHBF) is becoming an increasingly important manufacturing process for titanium alloy cylindrical workpiece in the aerospace industries. Finite element simulation is an essential tool for the specification of process parameters. In this paper, a two-dimensional nonlinear thermo-mechanical couple FE model was established. Numerical simulation of vacuum hot bulge forming of titanium alloy cylindrical workpiece was carried out using FE analysis software MSC.Marc. The effects of process parameter on vacuum hot bulge forming of BT20 titanium alloy cylindrical workpiece was analyzed by numerical simulation. The proposed an optimized vacuum hot bulge forming process parameters and die size. And the corresponding experiments were carried out. The simulated results agreed well with the experimental results.

Sign in / Sign up

Export Citation Format

Share Document