Influence of Dry Cut and Tool Wear on Residual Stresses in High Speed Machining of Nickel-Based Superalloy

2013 ◽  
Vol 768-769 ◽  
pp. 470-477 ◽  
Author(s):  
Ru Lin Peng ◽  
Jin Ming Zhou ◽  
Sten Johansson ◽  
Annethe Bellinius ◽  
Volodymr Bushlya ◽  
...  
Keyword(s):  
Tool Wear ◽  
Residual Stresses ◽  
High Speed ◽  
Flank Wear ◽  
Cutting Fluid ◽  
Cutting Condition ◽  
Minor Effect ◽  
Contrast Imaging ◽  
Tool Flank Wear ◽  
Tensile Stresses

Machining induced residual stresses were investigated in Inconel 718 prepared by high speed turning under dry cut condition. The influence of cutting tool wear and the use of cutting fluid were studied. By x-ray diffraction measurements, characteristic residual stress distributions with tensile stresses in the top layer and compressive stresses in the layer below were found in all the investigated samples. The magnitude of surface tensile stresses and size of the tension as well as compression zones varied depending on the cutting condition. The application of cutting fluid for turning using new tool has a minor effect, giving a somewhat larger subsurface compressive zone but reducing the surface tensile stresses. Tool flank wear has shown a much stronger effect. While a flank wear of VBmax=0.15 mm enhanced mostly the surface tensile residual stresses, a severer wear of VBmax=0.3 mm greatly increased the thickness of the subsurface compression zone and at the same time resulted in strong stress anisotropy. Microstructural study by electron channelling contrast imaging shows that the observed influence of tool flank wear or cutting fluid on residual stresses are related to different contributions from increased plastic deformation and cutting heat, which changed with the cutting conditions.

Tool Life Analysis when Turning Ti-6Al-4V Using Vegetable Oil-Based Cutting Fluid

2017 ◽  
Vol 882 ◽  
pp. 36-40
Author(s):  
Salah Gariani ◽  
Islam Shyha ◽  
Connor Jackson ◽  
Fawad Inam
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Vegetable Oil ◽  
Flank Wear ◽  
Cutting Speed ◽  
Fractional Factorial ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Tool Flank Wear ◽  
Fluid Concentration

This paper details experimental results when turning Ti-6Al-4V using water-miscible vegetable oil-based cutting fluid. The effects of coolant concentration and working conditions on tool flank wear and tool life were evaluated. L27 fractional factorial Taguchi array was employed. Tool wear (VBB) ranged between 28.8 and 110 µm. The study concluded that a combination of VOs based cutting fluid concentration (10%), low cutting speed (58 m/min), feed rate (0.1mm/rev) and depth of cut (0.75mm) is necessary to minimise VBB. Additionally, it is noted that tool wear was significantly affected by cutting speeds. ANOVA results showed that the cutting fluid concentration is statistically insignificant on tool flank wear. A notable increase in tool life (TL) was recorded when a lower cutting speed was used.

Role of Tool Flank Wear and Machining Speed in Developing of Residual Stress in Machined Surface During High Speed Machining of Titanium Alloys

2015 ◽  
Author(s):  
Xueping Zhang ◽  
Rajiv Shivpuri ◽  
Anil K. Srivastava
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
High Speed ◽  
Flank Wear ◽  
Tool Geometry ◽  
High Speed Machining ◽  
Machined Surface ◽  
Tool Flank Wear ◽  
Machining Speed

Residual stresses generated from finish machining have a significant impact on the fatigue life of mechanical components by controlling crack initiation and propagation processes in their near subsurface. As governing variables, tool geometry, tool wear, machining parameter, work material property, and lubrication conditions have been widely studied to determine their effects on residual stress pattern in machined surface and subsurface. Among those parameters, tool flank wear was seldom fully investigated although tool flank wear, as well as machining speed, has been identified as the most important contributor to residual stress. Especially, tool flank wear becomes more significant due to the poor work thermal property during the high speed machining of titanium Ti-6Al-4V alloy. This study aims to investigate the combined role of tool flank wear and machining speed in developing residual stress in the machining of titanium alloy using finite element method. A microstructure sensitive material model based on Self Consistent Method (SCM) is adopted to incorporate the phase state and its transformations during machining cycle. Critical flank wear land and corresponding machining speeds are identified, beyond which compressive residual stresses are transferred into tensile residual stresses. High machining speeds demonstrate a distinct influence on residual stresses by means of promoting tool flank wear rate. The numerical simulation results are validated by empirical data provided in previous research.

The influence of tool flank wear on residual stresses induced by milling aluminum alloy

2009 ◽  
Vol 209 (9) ◽  
pp. 4502-4508 ◽  
Author(s):  
Z.T. Tang ◽  
Z.Q. Liu ◽  
Y.Z. Pan ◽  
Y. Wan ◽  
X. Ai
Keyword(s):  
Aluminum Alloy ◽  
Residual Stresses ◽  
Flank Wear ◽  
Tool Flank Wear

The Analysis of Tool Wear in Milling CFRP with Different Diamond Coated Tool

2015 ◽  
Vol 667 ◽  
pp. 231-236 ◽  
Author(s):  
Xiao Fan Yang ◽  
You Sheng Li ◽  
Guo Hong Yan ◽  
Ju Dong Liu ◽  
Dong Min Yu
Keyword(s):  
Tool Wear ◽  
Flank Wear ◽  
Milling Process ◽  
Cutting Condition ◽  
End Mill ◽  
Reinforced Plastics ◽  
Right Hand ◽  
Coated Tool ◽  
New Type ◽  
Fiber Reinforced Plastics

Carbon fiber-reinforced plastics (CFRP) are typical difficult-to-machine materials, which is easy to produce many defects such as burrs, dilacerations, layering in milling process. And selecting the appropriate cutting tool has become the key to machining CFRP with high quality and efficiency. In the paper, the machining principle of milling CFRP with new type end mill was analyzed. The diamond coating of general right-hand end mill, cross-flute router and fine-cross-nick router were used to cutting CFRP under the same cutting condition. Through the comparative analysis of the workpiece’s surface quality and tool wear, it concluded that: compared with right-hand diamond coated end mill, cross-flute diamond coated router or fine-cross-nick diamond coated router could effectively suppress the appearance of burrs and dilacerations; abnormal coating peeling appeared in the flank face of right-hand diamond coated end mill, forming the boundary wear, which accelerated wear failure; the flank wear of diamond coated cross-flute router and fine-cross-nick router were both abrasive wear. Due to having more cutting edge than cross-flute router in cutting process, the flank wear of fine-cross-nick router was slower, and the tool life was longer. So it was more suitable for cutting CFRP.

Experimental Study of Tool Wear during Quasi High Speed Turning Titanium Alloy with Large Cutting Depth

2014 ◽  
Vol 800-801 ◽  
pp. 548-552
Author(s):  
Li Fu Xu ◽  
Wei Liang Dong ◽  
Shu Tao Huang ◽  
Bao Lin Dai
Keyword(s):  
Experimental Data ◽  
Titanium Alloy ◽  
High Speed ◽  
Flank Wear ◽  
Rake Face ◽  
Cutting Depth ◽  
Tool Flank Wear ◽  
High Speed Turning ◽  
Flank Face ◽  
Cutting Speeds

The wear morphology of rake face and flank face of tool is investigated by turning titanium alloy TC4 with CBN solid tool. It has been observed that the main wear form of rake face and flank face of tool is groove wear. The relation between tool flank wear and cutting speeds, feed rate, and cutting depth obtained from experimental data is given.

Basic Investigation of Tool Wear

1963 ◽  
Vol 85 (1) ◽  
pp. 33-37 ◽  
Author(s):  
H. Takeyama ◽  
R. Murata
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Flank Wear ◽  
Cutting Temperature ◽  
Cutting Condition ◽  
Rate Process ◽  
Mechanical Abrasion ◽  
Fundamental Investigation ◽  
First Approximation ◽  
Basic Investigation

This paper treats a fundamental investigation of tool wear and tool life mainly from the viewpoint of flank wear. The result reveals that the mechanism of tool wear in turning can be classified into two basic types: The mechanical abrasion which is directly proportional to the cutting distance and independent of the temperature; and the other is, so to speak, a physicochemical type which is considered to be a rate process closely associated with the temperature, of course. Although it depends upon the cutting condition which type of wear plays a more important role, the latter is predominant under usual conditions. According to the analyses and the experimental results, it has been found out that the tool life from the standpoint of flank wear can be predicted to a first approximation by the initial cutting temperature.

Tool Wear Behavior in Turning Inconel 718 with Coated Inserts

2012 ◽  
Vol 499 ◽  
pp. 348-352 ◽  
Author(s):  
Xiao Li Zhu ◽  
Song Zhang ◽  
X.L. Xu ◽  
H.G. Lv
Keyword(s):  
Tool Wear ◽  
Inconel 718 ◽  
Flank Wear ◽  
Wear Behavior ◽  
Cutting Tools ◽  
Three Dimensional ◽  
Cutting Condition ◽  
Tool Holder ◽  
Final Failure ◽  
Coated Carbide

In the present study, an experimental investigation has been carried out in an attempt to monitor tool wear progress in turning Inconel 718 with coated carbide inserts under the wet cutting condition. First, each experimental test was conducted with a new cutting edge and the turning process was stopped at a certain interval of time. Secondly, the indexable insert was removed from the tool holder and the flank wear of the insert was measured using a three-dimensional digital microscopy (VHX-600E); and then the insert was clamped into the tool holder for the next turning experiment. The final failure of tool wear surfaces were examined under a scanning electron microscope (SEM) equipped with an energy dispersive X-ray spectrometer (EDS). It is indicated that significant flank wear was the predominant failure mode, and the abrasive, adhesive and oxidation wear were the most dominant wear mechanisms which directly control the deterioration and final failure of the cutting tools.

Surface Integrity of Die Material in High Speed Hard Machining, Part 1: Micrographical Analysis

1999 ◽  
Vol 122 (4) ◽  
pp. 620-631 ◽  
Author(s):  
T. I. El-Wardany ◽  
H. A. Kishawy ◽  
M. A. Elbestawi
Keyword(s):  
Tool Wear ◽  
Residual Stresses ◽  
Tool Steel ◽  
Surface Integrity ◽  
High Speed ◽  
Cutting Conditions ◽  
Metallographic Analysis ◽  
Tool Geometry ◽  
Machined Surface ◽  
Geometrical Defects

The effects of cutting conditions and tool wear on chip morphology and surface integrity during high speed machining of D2 tool steel (60–62 Hrc) are investigated experimentally and analytically in this paper. Polycrystalline Cubic Boron Nitride (PCBN) tools are used in this investigation. The chips and the subsurface of the workpiece are examined using optical and scanning electron microscopy. Microhardness measurements are performed on the surface and subsurface of the workpiece. The X-ray diffraction technique is used to measure the residual stresses induced in the machined surface. The paper is divided into two parts. Part 1 presents the results obtained from the micrographical analysis of the chips and the surfaces produced. Part 2 deals with microhardness and residual stresses of the machined surface. The micrographical analysis of the chips produced shows that different mechanisms of chip formation exist depending on the magnitude of the cutting pressure and tool wear. Saw toothed chips are produced during the machining of D2 tool steel if the cutting pressure exceeds approximately 4000 MPa. The metallographic analysis of the surface produced illustrates the damaged surface region that contains geometrical defects and changes in the subsurface metallurgical structure. The types of surface damage are dependent on the cutting conditions, tool geometry and the magnitude of the wear lands. [S1087-1357(00)00104-0]

Tool Wear in Ball-End Milling of Cr12MoV Die Steel Using an Indexable Cutter with the Asymmetric Inserts

2012 ◽  
Vol 500 ◽  
pp. 111-116
Author(s):  
Bin Zou ◽  
Chuan Zhen Huang ◽  
Zi Ye Liu ◽  
Xin Qiang Zhuang ◽  
Jun Wang
Keyword(s):  
Tool Wear ◽  
Flank Wear ◽  
End Milling ◽  
Cutting Conditions ◽  
Cutting Condition ◽  
Die Steel ◽  
Ball End Milling ◽  
Diffusion Wear ◽  
Flank Face ◽  
And Diffusion

Tool wear was investigated at the different cutting conditions in rough ball-end milling of Cr12MoV die steel using an indexable cutter with asymmetric inserts. The wear patterns on rake face and flank face of major insert and minor insert, and chip patterns were observed by VHX-600E large depth-of-view 3-D scanner. The relationships of tool wear and cutting conditions, and their mechanisms were discussed. The tool life was determined by the flank wear at No. 1 cutting condition. At Nos. 2-8 cutting conditions, the life of major inset and minor insert were determined by the wear of their rake faces and flank faces respectively. At No. 8 cutting condition, the tool wear was dominated by boundary wear, adhesion and diffusion wear, and the slight chipping. Both type and color of chips identified the cutting stability at the different cutting conditions.

Sign in / Sign up

Export Citation Format

Share Document