Synthesize CCTO Using Different Mixing Media

2016 ◽  
Vol 840 ◽  
pp. 87-90 ◽  
Author(s):  
Rosyaini Afindi Zaman ◽  
Mohamad Johari Abu ◽  
Saniah Abdul Karim ◽  
Julie Juliewatty Mohamed ◽  
Mohd Fadzil Ain ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
High Dielectric Constant ◽  
Electronic Devices ◽  
Sol Gel ◽  
Dielectric Materials ◽  
High Energy ◽  
High Energy Density ◽  
Dielectric Ceramic ◽  
Wide Range ◽  
High Dielectric

In recent years, there has been an increasing interest on high dielectric constant that have significant applications in electronic devices. Dielectric materials have many technological applications such as capacitors, resonators and filters. High dielectric ceramic capacitors based perovskite oxides are necessary for modern electronic devices and are found to be suitable for a wide range of applications. Subramanian et al. discovered the high dielectric constant of CaCu3Ti4O12 (CCTO) ~ 10,000 at room temperature. CCTO has the cubic perovskite crystal structure and high dielectric constant of ~ 104 up to 105 at radio frequency and good temperature stability over a wide temperature range [1,2]. These properties were desired for various microelectronic applications. With the high dielectric constant, the material can store more charge and the values make CCTO an attractive material for ultra-high energy density capacitors. However, this properties can be accomplished if single phase of CCTO is formed. Many research have been done recently on the synthesis of the cubic perovskite CCTO and many techniques are working such as sol-gel route [3], combustion techniques [4], molten salt process [5] and etc., but this technique is difficult and complex process during sample preparation.

scholarly journals Polymer Nanocomposites with High Energy Density Utilizing Oriented Nanosheets and High-Dielectric-Constant Nanoparticles

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 4780
Author(s):  
Yushu Li ◽  
Yao Zhou ◽  
Sang Cheng ◽  
Jun Hu ◽  
Jinliang He ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Energy Density ◽  
Polymer Nanocomposites ◽  
High Dielectric Constant ◽  
Vinylidene Fluoride ◽  
Dielectric Materials ◽  
High Energy ◽  
High Energy Density ◽  
Capacitive Energy Storage ◽  
High Dielectric

The development of high-energy-density electrostatic capacitors is critical to addressing the growing electricity need. Currently, the widely studied dielectric materials are polymer nanocomposites incorporated with high-dielectric-constant nanoparticles. However, the introduction of high-dielectric-constant nanoparticles can cause local electric field distortion and high leakage current, which limits the improvement in energy density. In this work, on the basis of conventional polymer nanocomposites containing high-dielectric-constant nanoparticles, oriented boron nitride nanosheets (BNNSs) are introduced as an extra filler phase. By changing the volume ratios of barium titanate (BT) and BNNSs, the dielectric property of polymer nanocomposites is adjusted, and thus the capacitive energy storage performance is optimized. Experimental results prove that the oriented BNNSs can suppress the propagation of charge carriers and decrease the conduction loss. Using poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) as the polymer matrix, the P(VDF-HFP)/BNNS/BT nanocomposite has a higher discharged energy density compared with the conventional nanocomposite with the freely dispersed BT nanoparticles.

Composition-Microstructure-Property Relationships in BaTiO3 with Mg Addition

2015 ◽  
Vol 659 ◽  
pp. 58-63
Author(s):  
Oratai Jongprateep ◽  
Tunchanoke Khongnakhon ◽  
Jednupong Palomas
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Barium Titanate ◽  
High Efficiency ◽  
High Dielectric Constant ◽  
Dielectric Materials ◽  
High Energy ◽  
High Energy Density ◽  
Low Dielectric ◽  
High Dielectric

Rising worldwide demands for energy encourages development of high-efficiency energy storage and capacitor components. Main requirements for dielectric materials employed in fabrication of high energy density capacitors include high dielectric constant, high dielectric breakdown strength, and low dielectric loss. Owing to its high dielectric constant and low dielectric loss [1], barium titanate is among common capacitor materials. Tailoring of dielectric properties of barium titanate can be achieved through controlled chemical composition, microstructure, and crystal structure. Synthesis and processing techniques, as well as doping of barium titanate, can be key factors to control the composition and structure, which consequently contribute to enhancement of dielectric constant in the material.

scholarly journals Polyarylene Ether Nitrile-Based High-k Composites for Dielectric Applications

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
Yong You ◽  
Chenhao Zhan ◽  
Ling Tu ◽  
Yajie Wang ◽  
Weibin Hu ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
High Dielectric Constant ◽  
Dielectric Materials ◽  
Dielectric Ceramic ◽  
Polyarylene Ether Nitrile ◽  
Effective Strategies ◽  
Low Dielectric ◽  
Flexible Polymer ◽  
Ceramic Fillers ◽  
High Dielectric

Flexible polymer-based composites exhibiting high dielectric constant as well as low dielectric loss have been intensively investigated for their potential utilization in electronics and electricity industry and energy storage. Resulting from the polar -CN on the side chain, polyarylene ether nitrile (PEN) shows relatively high dielectric constant which has been extensively investigated as one of the hot spots as dielectric materials. However, the dielectric constant of PEN is still much lower than the ceramic dielectrics such as BaTiO3, TiO2, and Al2O3. In this review, recent and in-progress advancements in the designing and preparing strategies to obtain high-k PEN-based nanocomposites are summarized. According to the types of the added fillers, the effects of organic fillers, dielectric ceramic fillers, and conductive fillers on electric properties of PEN-based composites are investigated. In addition, other factors including the structures and sizes of the additive, the compatibility between the additive agent and the PEN, and the interface which affects the dielectric properties of the obtained composite materials are investigated. Finally, challenges facing in the design of more effective strategies for the high-k PEN-based dielectric materials are discussed.

Nanostructures and dielectric properties of PVDF-based polymer films with high energy density and low energy losses

2015 ◽  
Vol 1740 ◽  
Author(s):  
Masahiko Ando ◽  
Naoki Yoshimoto ◽  
Yuichiro Yoshitake ◽  
Shuji Kato ◽  
Hidekazu Kodama ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Polymer Films ◽  
Polyvinylidene Fluoride ◽  
High Dielectric Constant ◽  
Electrical Energy ◽  
High Energy ◽  
High Energy Density ◽  
Β Phase ◽  
High Dielectric

ABSTRACTBased on the investigation of mechanism for large dielectric losses in relaxor fluorinated polymers, polyvinylidene fluoride (PVDF) derivatives, a new nanostructure-controlled PVDF based polymer films with low dielectric loss, tanδ < 1% (0.6%), and high dielectric constant, εr = 13 at frequency of 1 kHz, was proposed for electrical energy storage applications. The high dielectric loss was mainly due to the electric-field induced α-β phase transition, and one dimensional extension of P(VDF-TrFE)-g-PEMA films was found to reduce the α phase component resulting in reduction of the dielectric loss while keeping the high dielectric constant. In-situ FTIR measurements suggested a possibility of further reducing the dielectric-loss.

Enhanced dielectric properties and thermostability in polyimide composites with core-shell structured polyimide@BaTiO3 nanoparticles

2021 ◽  
pp. 095400832199352
Author(s):  
Wei Deng ◽  
Guanguan Ren ◽  
Wenqi Wang ◽  
Weiwei Cui ◽  
Wenjun Luo
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Energy Density ◽  
Breakdown Strength ◽  
In Situ Polymerization ◽  
Dielectric Materials ◽  
High Energy ◽  
Amic Acid ◽  
High Energy Density ◽  
Core Shell

Polymer composites with high dielectric constant and thermal stability have shown great potential applications in the fields relating to the energy storage. Herein, core-shell structured polyimide@BaTiO3 (PI@BT) nanoparticles were fabricated via in-situ polymerization of poly(amic acid) (PAA) and the following thermal imidization, then utilized as fillers to prepare PI composites. Increased dielectric constant with suppressed dielectric loss, and enhanced energy density as well as heat resistance were simultaneously realized due to the presence of PI shell between BT nanoparticles and PI matrix. The dielectric constant of PI@BT/PI composites with 55 wt% fillers increased to 15.0 at 100 Hz, while the dielectric loss kept at low value of 0.0034, companied by a high energy density of 1.32 J·cm−3, which was 2.09 times higher than the pristine PI. Moreover, the temperature at 10 wt% weight loss reached 619°C, demonstrating the excellent thermostability of PI@BT/PI composites. In addition, PI@BT/PI composites exhibited improved breakdown strength and toughness as compared with the BT/PI composites due to the well dispersion of PI@BT nanofillers and the improved interfacial interactions between nanofillers and polymer matrix. These results provide useful information for the structural design of high-temperature dielectric materials.

scholarly journals High-K dielectric sulfur-selenium alloys

2019 ◽  
Vol 5 (5) ◽  
pp. eaau9785 ◽  
Author(s):  
Sandhya Susarla ◽  
Thierry Tsafack ◽  
Peter Samora Owuor ◽  
Anand B. Puthirath ◽  
Jordan A. Hachtel ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Metal Oxides ◽  
High Dielectric Constant ◽  
Dielectric Material ◽  
Dielectric Strength ◽  
Dielectric Materials ◽  
High K ◽  
Device Applications ◽  
High K Dielectric ◽  
High Dielectric

Upcoming advancements in flexible technology require mechanically compliant dielectric materials. Current dielectrics have either high dielectric constant, K (e.g., metal oxides) or good flexibility (e.g., polymers). Here, we achieve a golden mean of these properties and obtain a lightweight, viscoelastic, high-K dielectric material by combining two nonpolar, brittle constituents, namely, sulfur (S) and selenium (Se). This S-Se alloy retains polymer-like mechanical flexibility along with a dielectric strength (40 kV/mm) and a high dielectric constant (K = 74 at 1 MHz) similar to those of established metal oxides. Our theoretical model suggests that the principal reason is the strong dipole moment generated due to the unique structural orientation between S and Se atoms. The S-Se alloys can bridge the chasm between mechanically soft and high-K dielectric materials toward several flexible device applications.

Microwave-Assisted Synthesis of High Dielectric Constant CaCu3Ti4O12 from Sol–Gel Precursor

2015 ◽  
Vol 44 (7) ◽  
pp. 2243-2249 ◽  
Author(s):  
Xin Ouyang ◽  
Peng Cao ◽  
Saifang Huang ◽  
Weijun Zhang ◽  
Zhaohui Huang ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
High Dielectric Constant ◽  
Sol Gel ◽  
Microwave Assisted Synthesis ◽  
Microwave Assisted ◽  
High Dielectric
Sign in / Sign up

Export Citation Format

Share Document