scholarly journals The Use of Borax in Deterring Flash Setting of High Calcium Fly Ash Based Geopolymer

2016 ◽  
Vol 857 ◽  
pp. 416-420 ◽  
Author(s):  
Antoni ◽  
Stephen Wibiatma Wijaya ◽  
Juan Satria ◽  
Agung Sugiarto ◽  
Djwantoro Hardjito
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Fly Ash ◽  
Chemical Composition ◽  
Setting Time ◽  
Chemical Properties ◽  
Physico Chemical ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Positive Effect

Geopolymer that was made with high CaO content fly ash was found to have higher compressive strength than the low CaO fly ash, using the same mixture composition. This effect could be due to the physico-chemical properties of the fly ash, in respect to its particle size or the chemical composition. Although it was not widely published, the occurrence of flash setting of geopolymer was known to occur when using high CaO content fly ash as the precursor. Geopolymer paste may solidify within minutes after the addition of alkali activators, making it very difficult to cast in big volume. This paper investigate the effect of borax addition to the high calcium fly ash-based geopolymer mixture to reduce the occurrence of flash setting. It was found that the setting time can be extended significantly, with the addition of 5% borax, by mass, of fly ash. The addition of borax also have positive effect on increasing the compressive strength of geopolymer.

scholarly journals Influence of Particle Size Distribution of High Calcium Fly Ash on HVFA Mortar Properties

2018 ◽  
Vol 20 (2) ◽  
pp. 51
Author(s):  
Antoni . ◽  
Hendra Surya Wibawa ◽  
Djwantoro Hardjito
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Fly Ash ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Setting Time ◽  
High Volume ◽  
High Volume Fly Ash ◽  
High Calcium ◽  
High Calcium Fly Ash

This study evaluates the effect of particle size distribution (PSD) of high calcium fly ash on high volume fly ash (HVFA) mortar characteristics. Four PSD variations of high calcium fly ash used were: unclassified fly ash and fly ash passing sieve No. 200, No. 325 and No. 400, respectively. The fly ash replacement ratio of the cementitious material ranged between 50-70%. The results show that with smaller fly ash particles size and higher levels of fly ash replacement, the workability of the mixture was increased with longer setting time. There was an increase in mortar compressive strength with finer fly ash particle size, compared to those with unclassified ones, with the highest strength was found at those with fly ash passing mesh No. 325. The increase was found due to better compactability of the mixture. Higher fly ash replacement reduced the mortar’s compressive strength, however, the rate was reduced when finer fly ash particles was used.

scholarly journals Reactivity of fly ashes milled in different milling devices

2019 ◽  
Vol 58 (1) ◽  
pp. 179-188 ◽  
Author(s):  
Yong-Sik Chu ◽  
Batmunkh Davaabal ◽  
Dae-Sung Kim ◽  
Sung-Kwan Seo ◽  
Yoo Kim ◽  
...  
Keyword(s):  
Particle Size ◽  
Fly Ash ◽  
Surface Area ◽  
Thermal Power ◽  
Chemical Properties ◽  
Particle Size Reduction ◽  
Attrition Mill ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Physical And Chemical

Abstract The effect of two different milling devices, namely attrition mill versus vibration mill, on the reactivity of fly ash was studied. High calcium fly ash from 4th Thermal power station of Ulaanbaatar (Mongolia) was used for the experiments. The raw and processed samples were characterized by XRD, SEM, Particle size distribution, BET, Blaine surface area and density measurements. The efficiency of 1 hour milling was evaluated with the Blaine surface area set to be more than 5000 cm2/g. The physical and chemical properties of the attrition milled fly ash changed not much compared to the vibration milled samples. For example the d50 particle size became reduced from 29 µm to 6 µm by attrition milling and in vibration milled fly ash it was reduced to 7 µm. The density increased from 2.44 g/cm3 of raw fly ash to 2.84 g/cm3 and 2.79 g/cm3 in attrition and vibration milled samples, respectively. Mechanical milling revealed not only a particle size reduction but also the formation of a denser microstructure. As a result the vibration milled fly ash showed a weaker interaction with the alkaline solution (8 M NaOH used here) compared to the attrition milled fly ash. Consequently, compressive strength of the binder prepared using the attrition milled fly ash was higher, 61 MPa, while for vibration milled fly ash it was 49 MPa. For comparison unmilled fly ash, it was 21 MPa.

The Investigation on Setting Time and Strength of High Calcium Fly Ash Based Geopolymer

2018 ◽  
Vol 881 ◽  
pp. 158-164 ◽  
Author(s):  
Remigildus Cornelis ◽  
Henricus Priyosulistyo ◽  
Iman Satyarno ◽  
Rochmadi
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Setting Time ◽  
Solid Ratio ◽  
Synthesis Parameters ◽  
Heat Curing ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Ambient Curing

Fly ash based geopolymer normally gets the optimum strength by heat curing. This is considered as a hindrance to in-situ applications. Therefore, development of fly ash based geopolymer that suitable for ambient curing will widen the application to the concrete structure. This paper reports the results of an experimental study on setting time and development of compressive strength of class C fly ash based geopolymer paste produced in ambient curing condition. The main synthesis parameters such as water to the geopolymer solid ratio, alkali to cementitious ratio and molarity of NaOH were varied to understand their individual effect on setting time and the mechanical properties of the resulting geopolymer. The results suggested that generally the setting time increased with the NaOH molarity and the compressive strength of 59 MPa was obtained for geopolymer mixture cured at ambient temperature for 28 days with alkali to a cementitious ratio of 0.35 and 10 M NaOH. The results will be useful for developing the knowledge of the use of high calcium fly ash in producing geopolymer. This would be beneficial to the understanding the future applications of this material as new binding material.

Effect of Plasticizers and Water on Properties of HCFA Geopolymers

2017 ◽  
Vol 733 ◽  
pp. 76-79 ◽  
Author(s):  
Ahmad B. Malkawi ◽  
Mohd Fadhil Nuruddin ◽  
Amir Fauzi ◽  
Hashem Al-Mattarneh ◽  
Bashar S. Mohammed
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Tap Water ◽  
Setting Time ◽  
Water Addition ◽  
Final Setting Time ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Different Types ◽  
Hardened Properties

In this study, different types of plasticizers were used to investigate their effects on the fresh and hardened properties of high calcium fly ash geopolymers (HCFA). Modified polycarboxylate polymers (G3) and lignin-based polymers (G1) were used as plasticizing admixtures and the results were compared to the effect of tap water addition. The results showed that all the admixtures used are effective in increasing the workability of the HCFA geopolymers mixtures and the workability increased by 25-48% compared to the control mixtures. However, the use of G3 has adversely affected the strength by a reduction of 20%. While the use of G1 reduced the final setting time by 7% which is critical in the case of HCFA geopolymers where the final setting time occurs within 70 minutes. Water can be considered as the best admixture in terms of cost, setting time, and effect on compressive strength and it can be used where medium workability enhancement is required.

Influence of Glass and Limestone Powders in High Calcium Fly Ash Geopolymer Paste on Compressive Strength and Microstructure

2019 ◽  
Vol 801 ◽  
pp. 397-403
Author(s):  
Pattanapong Topark-Ngarm ◽  
Tawatchai Tho-In ◽  
Vanchai Sata ◽  
Prinya Chindaprasirt ◽  
Trinh Cao
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Glass Powder ◽  
Sodium Hydroxide Solution ◽  
Setting Time ◽  
Limestone Powder ◽  
Hydration Reaction ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Geopolymer Paste

The effects of replacing high calcium fly ash with containment glass powder and limestone powder in the geopolymer are investigated in this paper. The high calcium fly ash was replaced by either glass powder or limestone powder at 20% and 40% by weight. The geopolymer paste was tested for setting time and compressive strength and evaluated of its microstructure on SEM, XRD, FTIR, and MIP. The results indicated that the setting time of geopolymer paste was increased with the replacement of glass powder and reduced by replacement of limestone powder. The compressive strengths were generally higher than those of controls. The maximum increase of compressive strength was 33% when replaced fly ash with 20% of glass powder at 8 molar NaOH concentration of sodium hydroxide solution. The microstructure evaluations show the remaining particles of raw materials and the compatible of hydration reaction and polymerization when having limestone powder in the mix proportion. Furthermore, the powder acts as a filler in the gels.

Geopolymer Synthesis Using Metakaolin and High Calcium Fly Ash as Binary System Geopolymer

2020 ◽  
Vol 1007 ◽  
pp. 65-70
Author(s):  
Thammaros Pantongsuk ◽  
Chayanee Tippayasam ◽  
Pakamon Kittisayarm ◽  
Siripan Nilpairach ◽  
Duangrudee Chaysuwan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Construction Material ◽  
Construction Materials ◽  
Chemical Properties ◽  
Waste Products ◽  
X Ray ◽  
Alternative Construction ◽  
High Calcium ◽  
High Calcium Fly Ash

Conventional cement production process emits tons of carbon dioxide gas which is one of the greenhouse gases that influence the environment across the world. Discovering the alternative construction material with the eco-friendly process and the performance similar to or greater than ordinary Portland cement has been attractive to find out. This research presented green construction materials or so-called geopolymers from metakaolin substituted by high calcium fly ash by 20, 40, 60, 80 and 100 wt%. Some researches reported that geopolymer produced from metakaolin and fly ash with alkali solution gave a great result, but usually, they used fly ash containing very low calcium component. Compressive strength at 3, 7 and 28 curing days and flowability were conducted. The compressive strength of geopolymers blended with high calcium fly ash was still developed as the curing day increased and revealed the highest at 28 days especially on MK40 (high calcium fly ash 60 wt%). Geopolymer pastes prepared with a higher amount of high calcium fly ash exhibited less viscous. It was proved that the high amount of high calcium fly ash could be applied and gave extraordinary compressive strength. Furthermore, X-ray diffraction and X-ray fluorescence were used to investigate chemical properties as well as microstructure by a scanning electron microscope. For phase analysis, the existence of oxides of calcium and sulfur in high calcium fly ash resulted in the formation of thenardite, calcite, portlandite and C-S-H phase associating with geopolymeric phase. Therefore, this research proposed the opportunity for geopolymer production by using abundant high calcium fly ash to raise the value of the industrial waste products and green alternative construction material compared with OPC.

scholarly journals Novel Analytical Method for Mix Design and Performance Prediction of High Calcium Fly Ash Geopolymer Concrete

Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 900
Author(s):  
Chamila Gunasekara ◽  
Peter Atzarakis ◽  
Weena Lokuge ◽  
David W. Law ◽  
Sujeeva Setunge
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Gradient Algorithm ◽  
Geopolymer Concrete ◽  
Statistical Regression ◽  
Solid Ratio ◽  
Marquardt Algorithm ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Matlab Programming

Despite extensive in-depth research into high calcium fly ash geopolymer concretes and a number of proposed methods to calculate the mix proportions, no universally applicable method to determine the mix proportions has been developed. This paper uses an artificial neural network (ANN) machine learning toolbox in a MATLAB programming environment together with a Bayesian regularization algorithm, the Levenberg-Marquardt algorithm and a scaled conjugate gradient algorithm to attain a specified target compressive strength at 28 days. The relationship between the four key parameters, namely water/solid ratio, alkaline activator/binder ratio, Na2SiO3/NaOH ratio and NaOH molarity, and the compressive strength of geopolymer concrete is determined. The geopolymer concrete mix proportions based on the ANN algorithm model and contour plots developed were experimentally validated. Thus, the proposed method can be used to determine mix designs for high calcium fly ash geopolymer concrete in the range 25–45 MPa at 28 days. In addition, the design equations developed using the statistical regression model provide an insight to predict tensile strength and elastic modulus for a given compressive strength.

scholarly journals Resistance to Sulfuric Acid Corrosion of Geopolymer Concrete Based on Different Binding Materials and Alkali Concentrations

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7109
Author(s):  
Wei Yang ◽  
Pinghua Zhu ◽  
Hui Liu ◽  
Xinjie Wang ◽  
Wei Ge ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Corrosion Resistance ◽  
Sulfuric Acid ◽  
Fly Ash ◽  
Acid Corrosion ◽  
Geopolymer Concrete ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Naoh Solution ◽  
Sulfuric Acid Corrosion

Geopolymer binder is expected to be an optimum alternative to Portland cement due to its excellent engineering properties of high strength, acid corrosion resistance, low permeability, good chemical resistance, and excellent fire resistance. To study the sulfuric acid corrosion resistance of geopolymer concrete (GPC) with different binding materials and concentrations of sodium hydroxide solution (NaOH), metakaolin, high-calcium fly ash, and low-calcium fly ash were chosen as binding materials of GPC for the geopolymerization process. A mixture of sodium silicate solution (Na2SiO3) and NaOH solution with different concentrations (8 M and 12 M) was selected as the alkaline activator with a ratio (Na2SiO3/NaOH) of 1.5. GPC specimens were immersed in the sulfuric acid solution with the pH value of 1 for 6 days and then naturally dried for 1 day until 98 days. The macroscopic properties of GPC were characterized by visual appearance, compressive strength, mass loss, and neutralization depth. The materials were characterized by SEM, XRD, and FTIR. The results indicated that at the immersion time of 28 d, the compressive strength of two types of fly ash-based GPC increased to some extent due to the presence of gypsum, but this phenomenon was not observed in metakaolin-based GPC. After 98 d of immersion, the residual strength of fly ash based GPC was still higher, which reached more than 25 MPa, while the metakaolin-based GPC failed. Furthermore, due to the rigid 3D networks of aluminosilicate in fly ash-based GPC, the mass of all GPC decreased slightly during the immersion period, and then tended to be stable in the later period. On the contrary, in metakaolin-based GPC, the incomplete geopolymerization led to the compressive strength being too low to meet the application of practical engineering. In addition, the compressive strength of GPC activated by 12 M NaOH was higher than the GPC activated by 8 M NaOH, which is owing to the formation of gel depended on the concentration of alkali OH ion, low NaOH concentration weakened chemical reaction, and reduced compressive strength. Additionally, according to the testing results of neutralization depth, the neutralization depth of high-calcium fly ash-based GPC activated by 12 M NaOH suffered acid attack for 98 d was only 6.9 mm, which is the minimum value. Therefore, the best performance was observed in GPC prepared with high-calcium fly ash and 12 M NaOH solution, which is attributed to gypsum crystals that block the pores of the specimen and improve the microstructure of GPC, inhibiting further corrosion of sulfuric acid.

Sign in / Sign up

Export Citation Format

Share Document