Palm Oil Mill Effluent Treatment Using Electrocoagulation-Adsorption Hybrid Process

2020 ◽  
Vol 997 ◽  
pp. 139-149
Author(s):  
Yong Yin Sia ◽  
Ivy Ai Wei Tan ◽  
Mohammad Omar Abdullah
Keyword(s):  
Palm Oil ◽  
Alternative Treatment ◽  
Oxygen Demand ◽  
Total Suspended Solid ◽  
Suspended Solid ◽  
Effluent Treatment ◽  
Palm Oil Mill Effluent ◽  
Hybrid Process ◽  
Multi Stage ◽  
Palm Oil Mill

Palm oil processing is a multi-stage operation which generates large amount of palm oil mill effluent (POME). Due to its potential to cause environmental pollution, POME must be treated prior to discharge. Electrocoagulation (EC), adsorption (AD), combined EC and AD, and EC integrated with AD have demonstrated great potential to remove various organic and inorganic pollutants from wastewater. Up to date, no study has been found on POME treatment using EC-AD hybrid process. Therefore, this study aims to investigate the feasibility of applying EC-AD hybrid process as an alternative treatment for POME. The EC-AD hybrid process achieved higher removal of total suspended solid (TSS), chemical oxygen demand (COD) and colour as compared to EC and AD stand-alone processes. The EC-AD hybrid process reduced 79% of TSS, 44% of COD and 89% of colour from POME. The adsorption kinetics of TSS, COD and colour were best interpreted using pseudo-second-order model, which indicated that the adsorption rate was mainly controlled by chemisorption. Overall, the EC-AD hybrid process could be recommended as an alternative treatment for POME.

Treatment of Palm Oil Mill Effluent by Electrocoagulation Process

2012 ◽  
Vol 610-613 ◽  
pp. 363-367
Author(s):  
Tipakorn Suwannarat ◽  
Nipon Pisutpaisal ◽  
Siriorn Boonyawanich
Keyword(s):  
Palm Oil ◽  
Contact Time ◽  
Batch Reactor ◽  
Oxygen Demand ◽  
Total Suspended Solid ◽  
Suspended Solid ◽  
Steel Plates ◽  
Palm Oil Mill Effluent ◽  
Electrocoagulation Process ◽  
Palm Oil Mill

The purpose of current study was to examine the ability of electrocoagulation in decreasing chemical oxygen demand (COD) and total suspended solid (TSS) constituted in palm oil mill effluent. Bench-scale batch reactor containing two aluminum or steel plates (10 cm width × 30 cm height with 0.1 cm thickness) serving as electrodes with the interval distance of 3 cm was set up. The wastewater with COD concentration of 68,425 mg L-1 was treated in the reactor under the varied direct currents (0.3-1.3 A) and contact time (30-120 min). Sodium chloride was added to the wastewater to obtain the final concentration of 2 g L-1 (conductivity of 10 ms) prior to being fed into the reactor. The results showed that higher treatment efficiency when the aluminum was used as electrodes compared to the steel. COD removal efficiency was directly proportional to the contact time. The maximum COD and TSS removal observed at 1.3 A current input and 60 min contact time are 74.1 and 77.0%, respectively.

Batch Treatment of Palm Oil Mill Effluent

2009 ◽  
Vol 62-64 ◽  
pp. 759-762
Author(s):  
F.A. Aisien ◽  
A.A. Ojarikre ◽  
E.T. Aisien
Keyword(s):  
Palm Oil ◽  
Oxygen Demand ◽  
Chloride Ion ◽  
Total Suspended Solid ◽  
Suspended Solid ◽  
Palm Oil Mill Effluent ◽  
Significant Treatment ◽  
Physiochemical Parameters ◽  
Palm Oil Mill ◽  
Batch Treatment

Batch treatment of palm oil mill effluent (POME) was investigated using physical, chemical and biological methods. Physiochemical parameters such as pH, sulphate (SO42-), total dissolved solids (TDS), total suspended solid (TSS), chloride ion (Cl-), biological oxygen demand (BOD), chemical oxygen (COD) and metals (Fe2+, Zn2+, Ca2+ and Mg2+) concentrations were determined using American Public Health Association (APHA) methods. The results revealed that significant treatment was achieved at each stage. However, the biological method proved to be the best with percentage reductions of 45.6%, 97.6%, 71,0%, 50.1%, 80.4%, 93.8%, 72.0%, 85.4%, 93.2%, 77.7%, 86.2% and 85.7% for pH, SO42-, TS, TDS, TSS, Cl-, BOD, COD, Fe2+, Zn2+, Ca2+ and Mg2+ respectively. The concentrations after treatment were in conformity with the minimum acceptable standard of FEPA and WHO.

Effect of Different Mediators on Bio-Energy Generation and Palm Oil Mill Effluent Treatment in an Air-Cathode Microbial Fuel Cell-Adsorption System

2021 ◽  
Vol 411 ◽  
pp. 67-78
Author(s):  
Ivy Ai Wei Tan ◽  
J.R. Selvanathan ◽  
M.O. Abdullah ◽  
N. Abdul Wahab ◽  
D. Kanakaraju
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Palm Oil ◽  
Oxygen Demand ◽  
Energy Generation ◽  
Effluent Treatment ◽  
Palm Oil Mill Effluent ◽  
Adsorption System ◽  
Air Cathode ◽  
Palm Oil Mill

Palm oil mill effluent (POME) discharged without treatment into watercourses can pollute the water source. Microbial fuel cell (MFC) has gained high attention as a green technology of converting organic wastewater into bio-energy. As an approach to overcome the limitations of the existing POME treatment methods, air-cathode MFC-Adsorption system is introduced as an innovative technology to treat POME and generate bio-electricity simultaneously. However, the use of conventional MFC with proton exchange membrane in large scale applications is restricted by the high cost and low power generation. Addition of mediator in MFC is essential in order to increase the electron transfer efficiency, hence enhancing the system performance. This study therefore aims to investigate the effect of different type of mediators i.e. congo red (CR), crystal violet (CV) and methylene blue (MB) on the performance of an affordable air-cathode MFC-Adsorption system made from earthen pot with POME as the substrate. The addition of different mediators altered the pH of the MFC-Adsorption system, in which more alkaline system showed better performance. The voltage generated in the system with CR, CV and MB mediator was 120.58 mV, 168.63 mV and 189.25 mV whereas the current generated was 2.41 mA, 3.37 mA and 3.79 mA, respectively. The power density of 290.79 mW/m3, 568.72 mW/m3 and 716.31 mW/m3 was produced in the MFC-Adsorption system with CR, CV and MB mediator, respectively. The highest POME treatment efficiency was achieved in MFC-Adsorption system with MB mediator, which resulted in biochemical oxygen demand, chemical oxygen demand, total suspended solids, turbidity and ammoniacal nitrogen removal of 75.3%, 84.8%, 91.5%, 86.1% and 23.31%, respectively. Overall, the air-cathode MFC-Adsorption system with addition of MB mediator was feasible for POME treatment and simultaneous bio-energy generation.

Removal of Oily Wastewater Using Chitosan-filled Filter Media

2015 ◽  
Vol 74 (7) ◽  
Author(s):  
Aziatul Niza Sadikin ◽  
Mohd Ghazali Mohd Nawawi ◽  
Norasikin Othman ◽  
Roshafima Rasit Ali ◽  
Umi Aisah Asli
Keyword(s):  
Palm Oil ◽  
Suspended Solids ◽  
Total Suspended Solid ◽  
Suspended Solid ◽  
Palm Oil Mill Effluent ◽  
Filter Media ◽  
Fibrous Media ◽  
Filtration Process ◽  
Empty Fruit Bunches ◽  
Palm Oil Mill

The aim of this research is to evaluate the feasibility of the fibrous media for removal of total suspended solid and oil grease from palm oil mill effluent (POME). Wet lay-up method was adopted for filter fabrication where empty fruit bunches (EFB) were matted together with chitosan in non-woven manner. Chitosan-filled filter media were tested for their ability to reduce Total Suspended Solids (TSS) and Oil & Grease (O&G) from palm oil mill effluent. Filtration process results indicated that chitosan-filled filter media filtration only removed up to 28.14% of TSS and 29.86% of O&G. 

scholarly journals The Application of Nanofiltration Membrane for Palm Oil Mill Effluent Treatment by Adding Polyaluminium Chloride (PAC) as Coagulant

2020 ◽  
Vol 15 (1) ◽  
pp. 1-9
Author(s):  
Jhon Armedi Pinem ◽  
Imanuel Tumanggor ◽  
Edy Saputra
Keyword(s):  
Palm Oil ◽  
Treatment Process ◽  
Oxygen Demand ◽  
Effluent Treatment ◽  
Palm Oil Mill Effluent ◽  
Operating Pressure ◽  
Nanofiltration Membrane ◽  
Palm Oil Mill ◽  
Flocculation Process ◽  
Polyaluminium Chloride

The rapid development of Crude Palm Oil (CPO) production has led to an increase in the production of Palm Oil Mill Effluent (POME) as well. POME will cause problems in the environment because contains high contaminants. This study aims to investigate the effect of the coagulant Polyaluminium Chloride (PAC) variations and the membrane’s operating pressure on the POME treatment process using the nanofiltration membrane (NF) with the coagulation-flocculation process as pre-treatment. The PAC was used in the coagulation-flocculation process with variations in concentration (5.0; 5.5; 6.0; 6.5; 7.0 g/L). The process was completed by a rapid stirring of 200 rpm for 5 minutes, followed with slow stirring at 60 rpm for 15 minutes and settling time for 30 minutes. The process of membrane nanofiltration was carried out for 60 minutes with variations in operating pressure (8.0; 9.0; and 10 bars). In each treatment process, effluent quality testing was carried out with Biochemical Oxygen Demand (BOD5), Chemical Oxygen Demand (COD), Total Suspended Solid (TSS) and oil/fat as parameters. In addition, an analysis of permeate fluxes and rejection of NF membrane was also carried out. The results of the analysis suggested that the best coagulant doses are 6.0 g/L with the reduction percentage of BOD, COD, TSS and oil/fat at 78.85%; 68.57%; 92.77% and 92.31% respectively. The highest percentage of NF membrane rejection was found at a pressure of 10 bar, which is equal to 94.71%; 94.86%; 97.92% and 95% respectively for BOD, COD, TSS and oil/fat with a flux value of 7.16 L/m2.hours.

Performance of Chitosan and Polyglutamic Acid in Palm Oil Mill Effluent Treatment

2021 ◽  
pp. 147-173
Author(s):  
Man Djun Lee ◽  
Pui San Lee
Keyword(s):  
Environmental Pollution ◽  
Palm Oil ◽  
Public Awareness ◽  
Oxygen Demand ◽  
Pollutant Removal ◽  
Effluent Treatment ◽  
Palm Oil Mill Effluent ◽  
Polyglutamic Acid ◽  
Palm Oil Mill ◽  
Pollutants Removal

This chapter presents the study on pollutant removal efficiency in palm oil mill effluent using chitosan and polyglutamic acid (PGA). Up until today, palm oil mill effluent (POME) has been considered one of the significant sources of environmental pollution. The characteristics of POME include contaminating the source of drinking water, which is also harmful to the aquatic ecosystem by creating a highly acidic environment or causing eutrophication. With increasing public awareness of environmental pollution, it creates the need to address this issue. Both chitosan and PGA are non-polluting food-based anionic and biodegradable biopolymers that are environmentally friendly in wastewater treatment. The critical parameter to determine the effectiveness of pollutants removal is chemical oxygen demand, colour, and total suspended solids. In this aspect, this chapter also discussed some of the significant findings done in previous studies to provide proper understandings and implications on this topic.

scholarly journals TIO2-ENABLED POLYVYNYLIDENE FLUORIDE FOR PALM OIL MILL EFFLUENT TREATMENT: EFFECTS OF MEMBRANE MORPHOLOGY AND AERATION ON FLUX AND SUSPENDED SOLID REMOVAL

2021 ◽  
Vol 84 (1) ◽  
pp. 107-115
Author(s):  
Erna Yuliwaty ◽  
Ahmad Fauzi Ismail ◽  
Goh Pei Sean ◽  
Sri Martini
Keyword(s):  
Palm Oil ◽  
Membrane Fouling ◽  
Polyvinylidene Fluoride ◽  
Membrane Surface ◽  
Suspended Solid ◽  
Effluent Treatment ◽  
Palm Oil Mill Effluent ◽  
Mixed Matrix Membrane ◽  
Membrane Pore ◽  
Palm Oil Mill

A polyvinylidene fluoride-based mixed matrix membrane (PVDF- MMM) has been developed to treat palm oil mill effluent (POME). The addition of TiO2 into PVDF membrane was conducted. Hollow fibers were spun from a dope solution containing PVDF/PVP 30K/DMAc/additives by using a dry-jet wet spinning process at different air gaps. AFM image demonstrated that wet spun hollow fiber had a rougher outer surface than that of dry-jet wet spun fibers and exhibited symmetric cross-section structure. Experimental results showed that hydrophilicity of membranes increased with adding of TiO2 particles and the varied air gap length influenced the characteristic of membrane pore size and outer membrane surface roughness. In addition, aeration could increase the turbulence and flux and reduce membrane fouling. The values of flux and suspended solids removal were 92.04 L/m2.hr and 94.86 %, respectively, with the varied aeration flow rate of 2.0, 3.0 and 4.0 mL/min and bubble size distribution of 4.0 µm. Overall, this study has proven that PVDF-based MMM could achieve expected performance for POME treatment.

Performance of cellulose acetate – polyethersulphone blend membrane prepared using microwave heating for palm oil mill effluent treatment

2007 ◽  
Vol 56 (8) ◽  
pp. 169-177 ◽  
Author(s):  
A. Idris ◽  
I. Ahmed ◽  
H.W. Jye
Keyword(s):  
Cellulose Acetate ◽  
Microwave Heating ◽  
Palm Oil ◽  
Oxygen Demand ◽  
Effluent Treatment ◽  
Palm Oil Mill Effluent ◽  
Conventional Heating ◽  
Permeate Flux ◽  
Blend Membranes ◽  
Palm Oil Mill

The objective of this research is to investigate the performance of blend cellulose acetate (CA)–polyethersulphone (PES) membranes prepared using microwave heating (MWH) techniques and then compare it with blend CA-PES membranes prepared using conventional heating (CH) methods using bovine serum albumin solution. The superior membranes were then used in the treatment of palm oil mill effluent (POME). Various blends of CA-PES have been blended with PES in the range of 1–5 wt%. This distinctive series of dope formulations of blend CA/PES and pure CA was prepared using N, N-dimethylformamide (DMF) as solvent. The dope solution was prepared by MW heating for 5 min at a high pulse and the membranes were prepared by phase inversion method. The performances of these membranes were evaluated in terms of pure water and permeate flux, percentage removal of total suspended solids (TSS), chemical oxygen demand (COD) and biochemical oxygen demand (BOD). The results indicate that blend membranes prepared using the microwave technique is far more superior compared to that prepared using CH. Blend membranes with 19% CA, 1–3% PES and 80% of DMF solvent were found to be the best membrane formulation.

Survivability of Alcaligenaceae and Chromatiaceae as palm oil mill effluent pollution bioindicators under fluctuations of temperature, pH and total suspended solid

2021 ◽  
Author(s):  
Noor Shaidatul Lyana Mohamad-Zainal ◽  
Norhayati Ramli ◽  
Nurhasliza Zolkefli ◽  
Nurul Asyifah Mustapha ◽  
Mohd Ali Hassan ◽  
...  
Keyword(s):  
Palm Oil ◽  
Total Suspended Solid ◽  
Suspended Solid ◽  
Palm Oil Mill Effluent ◽  
Palm Oil Mill

scholarly journals Phytoremediation of Palm Oil Mill Effluent (POME) Using Eichhornia crassipes

2019 ◽  
Vol 6 (1) ◽  
pp. 340-354 ◽  
Author(s):  
Ivy Tan Ai Wei
Keyword(s):  
Palm Oil ◽  
Retention Time ◽  
Eichhornia Crassipes ◽  
Industrial Effluent ◽  
Oxygen Demand ◽  
Total Suspended Solid ◽  
Good Alternative ◽  
Potential Method ◽  
Palm Oil Mill Effluent ◽  
Palm Oil Mill

It is inevitable that the manufacturing process of palm oil is accompanied by the generation of a massive amount of high strength wastewater, namely palm oil mill effluent (POME), which could pose serious threat to the aquatic environment. POME which contains high organic compounds originating from biodegradable materials causes water pollution if not properly managed. Palm oil industries are facing the challenges to make ends meet in the aspects of natural assurance, financial reasonability and development sustainability. It is therefore crucial to seek a practical solution to achieve the goal of environmental protection while continuing the economic sustainability. Phytoremediation has been proven as a potential method for removal or degradation of various hazardous contaminants. However, research on phytoremediation of POME using Eichhornia crassipes (E. crassipes) is still limited. This study aims to determine the feasibility of applying phytoremediation technique using E. crassipes for POME treatment. The effects of pH, plant:POME ratio and retention time on the biochemical oxygen demand (BOD), chemical oxygen demand (COD) and total suspended solid (TSS) of POME were investigated. The highest BOD removal of 92.6% was achieved after 21 days retention time at pH 4 with plant:POME ratio of 1:20 kg/L. The highest COD removal of 20.7% was achieved after 14 days retention time at pH 6 with plant:POME ratio of 1:20 kg/L. Phytoremediation using E. crassipes was shown to be a promising eco-friendly technique for POME treatment, and is therefore recommended as a good alternative treatment solution for this industrial effluent.

Sign in / Sign up

Export Citation Format

Share Document