Strength of AAAS Composites with Ceramic Precursor over Time

2021 ◽  
Vol 322 ◽  
pp. 60-65
Author(s):  
Petr Frantík ◽  
Pavla Rovnaníková ◽  
Zbyněk Keršner
Keyword(s):  
Compressive Strength ◽  
Least Squares Method ◽  
Bending Tests ◽  
Three Point Bending ◽  
Dependent Change ◽  
Horizontal Asymptote ◽  
Ceramic Precursors ◽  
Time Dependent Change ◽  
Alkaline Activator ◽  
Alkali Activated

The paper deals with the approximation of the time evolution of the strengths of selected alkali-activated aluminosilicate (AAAS) composites based on ceramic precursors. Composites made of brick dust as a precursor and an alkaline activator with a silicate modulus of Ms = 0.8, 1.0, 1.2, 1.4, and 1.6 were investigated. The filler consisted of standard quartz sand in one case, and crushed brick in the other. The test specimens had nominal dimensions of 40 × 40 × 160 mm and were tested in three-point bending after 7, 28, 90, and 300 days of maturation. From each composite, 3 specimens were tested and the compressive strength was determined from the 6 specimen parts that remained after the bending tests. The obtained flexural and compressive strength values for the abovementioned 4 composite ages were approximated by the exponential function , where the coefficient a represents a horizontal asymptote to the approximation curve, i.e. the theoretical strength of the composite at time t = ∞; the exponential term of the approximation with the coefficients b and c expresses the degree of the time-dependent change of the respective compressive strength in the interval t = (0, ∞). The approximation was performed with the least squares method using genetic algorithms implemented in the Java GA package with open source code.

High Strength Alkali Activated Slag Cements with Controlled Setting Times and Early Strength Gain

2015 ◽  
Vol 1100 ◽  
pp. 44-49 ◽  
Author(s):  
Pavel Krivenko ◽  
Oleg Petropavlovsky ◽  
Vit Petranek ◽  
Vasiliy Pushkar ◽  
Grigorii Vozniuk
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Water Glass ◽  
High Strength ◽  
Strength Gain ◽  
Setting Times ◽  
Alkaline Activator ◽  
Early Strength ◽  
Activated Slag ◽  
Alkali Activated

The paper discusses approaches to compositional build-up of high strength alkali activated cements made using water glass as alkaline activator represented by commercial products in a form of powder and liquid. The purpose was to study the influence of fineness of ground granulated blast-furnace slags, admixtures and additives, compatible with alkali activated cements, water glass and mode of manufacturing technology in order to reach high compressive strength (≥ 80 MPa at standard age (28 days)) and early strength (≥ 20 MPa after 3 h of hardening in normal conditions).

Properties of Alkli-Activated Slag Cement Compounded with Soluble Glasses with a High Silicate Modulus

2013 ◽  
Vol 712-715 ◽  
pp. 905-908
Author(s):  
Qun Pan ◽  
Bin Zhu ◽  
Xiao Huang ◽  
Lin Liu
Keyword(s):  
Compressive Strength ◽  
Cement Mortar ◽  
Strength Characteristics ◽  
Slag Cement ◽  
Alkali Activated Slag ◽  
Cement Mortars ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Alkali Activated ◽  
High Silicate

Properties of alkali-activated slag cements compounded with soluble glasse with a high silicate modulus Ms=2.6 were detailedly studied in this paper, including compressive strength and flexure strength characterictics at the ages of 3,7,28 days and flow values of fresh cement mixtures on a jolting table. As a result, with the compressive strength at the age of 28 days of 95.6-107.8 MPa has been developed, and the flow values and strength characteristics of alkali-activated slag cement mortars increased with increase in a water to cement (alkaline activator solution to slag) ratio, and the flow value (determined on the cement mortar mixtures) would reach 145 mm. Moreover, the development speed of strength characteristics of mortar specimens would be affected negatively by increasing of water demand (requirement).

scholarly journals Effect of Sodium Aluminate Dosage as a Solid Alkaline Activator on the Properties of Alkali-Activated Slag Paste

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Bin Chen ◽  
Jun Wang ◽  
Jinyou Zhao
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Setting Time ◽  
Sodium Aluminate ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Alkali Activated Slag ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Alkali Activated

Extensive research into alkali-activated slag as a green gel material to substitute for cement has been done because of the advantages of low-carbon dioxide emissions and recycling of industrial solid waste. Alkali-activated slag usually has good mechanical properties, but the too fast setting time restricted its application and promotion. Changing the composition of alkaline activator could optimize setting time, usually making it by adding sodium carbonate or sodium sulfate but this would cause insufficient hydration reaction power and hinder compressive strength growth. In this paper, the effect of sodium aluminate dosage as an alkaline activator on the setting time, fluidity, compressive strength, hydration products, and microstructures was studied through experiments. It is fair to say that an appropriate amount of sodium aluminate could obtain a suitable setting time and better compressive strength. Sodium aluminate provided enough hydroxyl ions for the paste to promote the hydration reaction process that ensured obtaining high compressive strength and soluble aluminium formed precipitate wrapped on the surface of slag to inhibit the hydration reaction process in the early phase that prolonged setting time. The hydration mechanism research found that sodium aluminate played a key role in the formation of higher cross-linked gel hydration products in the late phase of the process. Preparing an alkali-activated slag with excellent mechanical properties and suitable setting time will significantly contribute to its application and promotion.

scholarly journals A Mix Design Procedure for Alkali-Activated High-Calcium Fly Ash Concrete Cured at Ambient Temperature

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Tanakorn Phoo-ngernkham ◽  
Chattarika Phiangphimai ◽  
Nattapong Damrongwiriyanupap ◽  
Sakonwan Hanjitsuwan ◽  
Jaksada Thumrongvut ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Design Methodology ◽  
Design Procedure ◽  
Mix Design ◽  
Fly Ash Concrete ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Alkaline Activator ◽  
Alkali Activated

This research focuses on developing a mix design methodology for alkali-activated high-calcium fly ash concrete (AAHFAC). High-calcium fly ash (FA) from the Mae Moh power plant in northern Thailand was used as a starting material. Sodium hydroxide and sodium silicate were used as alkaline activator solutions (AAS). Many parameters, namely, NaOH concentration, alkaline activator solution-to-fly ash (AAS/FA) ratio, and coarse aggregate size, were investigated. The 28-day compressive strength was tested to validate the mix design proposed. The mix design methodology of the proposed AAHFAC mixes was given step by step, and it was modified from ACI standards. Test results showed that the 28-day compressive strength of 15–35 MPa was obtained. After modifying mix design of the AAHFAC mixes by updating the AAS/FA ratio from laboratory experiments, it was found that they met the strength requirement.

Effect of the Combined Using of Fly Ash and Granulated Blast Furnace Slag on Properties of Cementless Alkali-Activated Mortar

2011 ◽  
Vol 287-290 ◽  
pp. 916-921
Author(s):  
Kyung Taek Koh ◽  
Gum Sung Ryu ◽  
Si Hwan Kim ◽  
Jang Hwa Lee
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Curing Temperature ◽  
Mixture Ratio ◽  
Granulated Blast Furnace Slag ◽  
Alkaline Activator ◽  
Furnace Slag ◽  
Alkali Activated

This paper examines the effects of the mixture ratio of fly ash/slag, the type of alkaline activators and curing conditions on the workability, compressive strength and microstructure of cementless alkali-activated mortar. The investigation showed that the mixture ratio of fly ash/slag and the type of alkaline activator have significant influence on the workability and strength, whereas the curing temperature has relatively poor effect. An alkali-activated mortar using a binder composed of 50% of fly ash and 50% of granulated blast furnace slag and alkaline activator made of 9M NaOH and sodium silicate in proportion of 1:1 is seen to be able to develop a compressive strength of 65 MPa at age of 28 days even when cured at ambient temperature of 20°C.

scholarly journals Artificial neural networks test for the prediction of chemical stability of pyroclastic deposits-based AAMs and comparison with conventional mathematical approach (MLR)

2020 ◽  
Vol 56 (1) ◽  
pp. 513-527
Author(s):  
Claudio Finocchiaro ◽  
Germana Barone ◽  
Paolo Mazzoleni ◽  
Caterina Sgarlata ◽  
Isabella Lancellotti ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Chemical Stability ◽  
Mechanical Performance ◽  
Calculated Data ◽  
Molar Ratio ◽  
Pyroclastic Deposits ◽  
Alkaline Activator ◽  
Artificial Neural ◽  
Artificial Neural Network Ann ◽  
Alkali Activated

Abstract The investigation on the reticulation degree of volcanic alkali-activated materials, AAMs, were experimentally determined in terms of chemico-physical properties: weight loss after leaching test in water, ionic conductivity and pH of the leachate and compressive strength. Artificial neural network (ANN) was successfully applied to predict the chemical stability of volcanic alkali-activated materials. Nine input data per each chemico-physical parameter were used to train each ANN. The training series of specific volcanic precursors were tested also for the other one. Excellent correlations between experimental and calculated data of the same precursor type were found reaching values around one. The evidence of strong effect on chemical stability of the alkaline activator SiO2/Na2O molar ratio as well as the Si/Al ratio of precursor mixtures on the reticulation degree of ghiara-based formulation with respect to volcanic ash-based materials is presented. It must be noted that such effect was much less pronounced on the compressive strength values, appearing more insensitive the molar ratio of the alkaline activator. The comparison of the ANN results with more conventional multiple linear regression (MLR) testifies the higher prediction performance of the first method. MLRs results, less significant, are useful to confirm the powerful capacity of ANNs to identify the more suitable formulation using a set of experimental AAMs. This study, as few others, on the correlation between chemical stability and compressive strength of AAMs provide a great contribution in the direction of durability and in-life mechanical performance of these class of materials. Graphic abstract

scholarly journals Effect of Dosage of Alkaline Activator on the Properties of Alkali-Activated Slag Pastes

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Zhenzhen Jiao ◽  
Ying Wang ◽  
Wenzhong Zheng ◽  
Wenxuan Huang
Keyword(s):  
Compressive Strength ◽  
Room Temperature ◽  
Setting Time ◽  
Drying Shrinkage ◽  
Engineering Properties ◽  
Alkali Activated Slag ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Good Workability ◽  
Alkali Activated

This study focused on the engineering properties of alkali-activated slag (AAS) pastes prepared by mixing an activator consisting of sodium silicate and sodium hydroxide at room temperature. The water-to-slag ratio of AAS paste was kept constant at 0.35 by mass. AAS pastes were prepared using the activator with five different silicate moduli of 1, 1.2, 1.4, 1.6, and 1.8 and three different Na2O contents of 6%, 8%, and 10%. The results showed that both the silicate moduli and Na2O contents had significant effects on the engineering properties of AAS pastes. All the AAS pastes exhibited properties such as fast setting, good workability, and high early compressive strength. The final setting time varied from 9 to 36 min, and the fluidity was in the range of 147–226 mm. The 1 d compressive strength of all the AAS pastes, which could be easily achieved, had values above 55 MPa, whereas the highest strength obtained was 102 MPa with the silicate modulus of 1 and Na2O content of 8% at room temperature. The drying shrinkage increased as the silicate modulus increased. Furthermore, the hydration products and microstructures of AAS pastes were explained according to the microanalysis methods.

scholarly journals Durability of alkali activated slag in a marine environment: Influence of alkali ion

2018 ◽  
Vol 83 (10) ◽  
pp. 1143-1156 ◽  
Author(s):  
Irena Nikolic ◽  
Milena Tadic ◽  
Ivona Jankovic-Castvan ◽  
Vuk Radmilovic ◽  
Velimir Radmilovic
Keyword(s):  
Compressive Strength ◽  
Marine Environment ◽  
Alkali Activated Slag ◽  
Lower Porosity ◽  
Seawater Environment ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Electric Arc Furnace Slag ◽  
Strength And Durability ◽  
Alkali Activated

The durability of alkali-activated steel electric arc furnace slag (EAFS) in a marine environment was evaluated with respect to the chemical composition of the alkaline activator. Two different alkaline activators have been used: a mixture of NaOH and Na2SiO3 solutions (Na-activator), as well as a mixture of KOH and K2SiO3 solutions (K-activator). The obtained results gave the insight into the influence of alkaline activator chemistry on the compressive strength and durability of alkali-activated slag (AAS), which was exposed to the damaging seawater environment. The porosity of AAS was found to be the most important factor with regards to the strength and durability of these materials in marine environment. Sodium based alkali-activated slag (Na-AAS) displayed lower porosity and higher compressive strength compared to potassium based AAS (K- -AAS). Lower porosity and thus a lower rate of water uptake by AAS matrix, i.e., the lower sorptivity was exhibited by the Na-AAS when compared to K-AAS. Hence, Na-AAS exhibited better durability in a marine environment.

Sign in / Sign up

Export Citation Format

Share Document