scholarly journals Effect of Sodium Aluminate Dosage as a Solid Alkaline Activator on the Properties of Alkali-Activated Slag Paste

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Bin Chen ◽  
Jun Wang ◽  
Jinyou Zhao
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Setting Time ◽  
Sodium Aluminate ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Alkali Activated Slag ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Alkali Activated

Extensive research into alkali-activated slag as a green gel material to substitute for cement has been done because of the advantages of low-carbon dioxide emissions and recycling of industrial solid waste. Alkali-activated slag usually has good mechanical properties, but the too fast setting time restricted its application and promotion. Changing the composition of alkaline activator could optimize setting time, usually making it by adding sodium carbonate or sodium sulfate but this would cause insufficient hydration reaction power and hinder compressive strength growth. In this paper, the effect of sodium aluminate dosage as an alkaline activator on the setting time, fluidity, compressive strength, hydration products, and microstructures was studied through experiments. It is fair to say that an appropriate amount of sodium aluminate could obtain a suitable setting time and better compressive strength. Sodium aluminate provided enough hydroxyl ions for the paste to promote the hydration reaction process that ensured obtaining high compressive strength and soluble aluminium formed precipitate wrapped on the surface of slag to inhibit the hydration reaction process in the early phase that prolonged setting time. The hydration mechanism research found that sodium aluminate played a key role in the formation of higher cross-linked gel hydration products in the late phase of the process. Preparing an alkali-activated slag with excellent mechanical properties and suitable setting time will significantly contribute to its application and promotion.

scholarly journals Effect of Dosage of Alkaline Activator on the Properties of Alkali-Activated Slag Pastes

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Zhenzhen Jiao ◽  
Ying Wang ◽  
Wenzhong Zheng ◽  
Wenxuan Huang
Keyword(s):  
Compressive Strength ◽  
Room Temperature ◽  
Setting Time ◽  
Drying Shrinkage ◽  
Engineering Properties ◽  
Alkali Activated Slag ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Good Workability ◽  
Alkali Activated

This study focused on the engineering properties of alkali-activated slag (AAS) pastes prepared by mixing an activator consisting of sodium silicate and sodium hydroxide at room temperature. The water-to-slag ratio of AAS paste was kept constant at 0.35 by mass. AAS pastes were prepared using the activator with five different silicate moduli of 1, 1.2, 1.4, 1.6, and 1.8 and three different Na2O contents of 6%, 8%, and 10%. The results showed that both the silicate moduli and Na2O contents had significant effects on the engineering properties of AAS pastes. All the AAS pastes exhibited properties such as fast setting, good workability, and high early compressive strength. The final setting time varied from 9 to 36 min, and the fluidity was in the range of 147–226 mm. The 1 d compressive strength of all the AAS pastes, which could be easily achieved, had values above 55 MPa, whereas the highest strength obtained was 102 MPa with the silicate modulus of 1 and Na2O content of 8% at room temperature. The drying shrinkage increased as the silicate modulus increased. Furthermore, the hydration products and microstructures of AAS pastes were explained according to the microanalysis methods.

scholarly journals The Effect of Different Types of Internal Curing Liquid on the Properties of Alkali-Activated Slag (AAS) Mortar

2021 ◽  
Vol 13 (4) ◽  
pp. 2407
Author(s):  
Guang-Zhu Zhang ◽  
Xiao-Yong Wang ◽  
Tae-Wan Kim ◽  
Jong-Yeon Lim ◽  
Yi Han
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Deionized Water ◽  
Internal Curing ◽  
Control Group ◽  
Alkali Activated Slag ◽  
Different Types ◽  
Naoh Solution ◽  
Activated Slag ◽  
Alkali Activated

This study shows the effect of different types of internal curing liquid on the properties of alkali-activated slag (AAS) mortar. NaOH solution and deionized water were used as the liquid internal curing agents and zeolite sand was the internal curing agent that replaced the standard sand at 15% and 30%, respectively. Experiments on the mechanical properties, hydration kinetics, autogenous shrinkage (AS), internal temperature, internal relative humidity, surface electrical resistivity, ultrasonic pulse velocity (UPV), and setting time were performed. The conclusions are as follows: (1) the setting times of AAS mortars with internal curing by water were longer than those of internal curing by NaOH solution. (2) NaOH solution more effectively reduces the AS of AAS mortars than water when used as an internal curing liquid. (3) The cumulative heat of the AAS mortar when using water for internal curing is substantially reduced compared to the control group. (4) For the AAS mortars with NaOH solution as an internal curing liquid, compared with the control specimen, the compressive strength results are increased. However, a decrease in compressive strength values occurs when water is used as an internal curing liquid in the AAS mortar. (5) The UPV decreases as the content of zeolite sand that replaces the standard sand increases. (6) When internal curing is carried out with water as the internal curing liquid, the surface resistivity values of the AAS mortar are higher than when the alkali solution is used as the internal curing liquid. To sum up, both NaOH and deionized water are effective as internal curing liquids, but the NaOH solution shows a better performance in terms of reducing shrinkage and improving mechanical properties than deionized water.

Experimental Study on Alkali-Activated Slag-Lithium Slag-Fly Ash Environmental Concrete

2011 ◽  
Vol 287-290 ◽  
pp. 1237-1240
Author(s):  
Lan Fang Zhang ◽  
Rui Yan Wang
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Setting Time ◽  
Alkali Activated Slag ◽  
Percent Increase ◽  
Compressive Strength Of Concrete ◽  
Activated Slag ◽  
Lithium Slag ◽  
Alkali Activated

The aim of this paper is to study the influence of lithium-slag and fly ash on the workability , setting time and compressive strength of alkali-activated slag concrete. The results indicate that lithium-slag and fly-ash can ameliorate the workability, setting time and improve the compressive strength of alkali-activated slag concrete，and when 40% or 60% slag was replaced by lithium-slag or fly-ash, above 10 percent increase in 28-day compressive strength of concrete were obtained.

Properties of Alkli-Activated Slag Cement Compounded with Soluble Glasses with a High Silicate Modulus

2013 ◽  
Vol 712-715 ◽  
pp. 905-908
Author(s):  
Qun Pan ◽  
Bin Zhu ◽  
Xiao Huang ◽  
Lin Liu
Keyword(s):  
Compressive Strength ◽  
Cement Mortar ◽  
Strength Characteristics ◽  
Slag Cement ◽  
Alkali Activated Slag ◽  
Cement Mortars ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Alkali Activated ◽  
High Silicate

Properties of alkali-activated slag cements compounded with soluble glasse with a high silicate modulus Ms=2.6 were detailedly studied in this paper, including compressive strength and flexure strength characterictics at the ages of 3,7,28 days and flow values of fresh cement mixtures on a jolting table. As a result, with the compressive strength at the age of 28 days of 95.6-107.8 MPa has been developed, and the flow values and strength characteristics of alkali-activated slag cement mortars increased with increase in a water to cement (alkaline activator solution to slag) ratio, and the flow value (determined on the cement mortar mixtures) would reach 145 mm. Moreover, the development speed of strength characteristics of mortar specimens would be affected negatively by increasing of water demand (requirement).

scholarly journals Effect of Cr6+ on the Properties of Alkali-Activated Slag Cement

2021 ◽  
Vol 8 ◽  
Author(s):  
Fu Bo ◽  
Cheng Zhenyun
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Cement Stone ◽  
Slag Cement ◽  
Hydration Kinetics ◽  
Alkali Activated Slag ◽  
Dual Beam ◽  
Press Method ◽  
Activated Slag ◽  
Alkali Activated

In order to investigate the effect of Cr6+ on the properties of alkali-activated slag cement (AAS), the effects of added dosage of Na2Cr2O4 on the setting time and compressive strength of AAS were measured. The leaching concentration of Cr6+ from AAS cement stone was measured using dual-beam UV-visible spectrophotometry. The effect of Na2Cr2O4 on the hydration kinetics of AAS cement was monitored by microcalorimetry and the corresponding kinetic parameters were analyzed. The pore solution from AAS was collected and analyzed using the high pressure press method. The effects of Na2Cr2O4 on the hydration products of AAS cement were observed and compared using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The experimental results showed that the AAS hydration process was markedly affected by Na2Cr2O4 dosage. The setting time of AAS pastes was increased and the compressive strength of cement stones was reduced with increasing dosage of Na2Cr2O4. With the development of AAS hydration, the leaching concentration of Na2Cr2O4 gradually decreased. Na2Cr2O4 did not affect the dissolution of slag particles, but impeded the formation of C-S-H gel. The Cr6+ was immobilized chemically in the form of needle-like CaCrO4 particles formed by the chemical reaction between Na2Cr2O4 and Ca2+ leaching from the slag.

scholarly journals Effect of Rheology of Fresh Paste on the Pore Structure and Properties of Pervious Concrete Based on the High Fluidity Alkali-Activated Slag

Crystals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 593
Author(s):  
Haining Geng ◽  
Qing Xu ◽  
Saiful B. Duraman ◽  
Qiu Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Pore Structure ◽  
Water Permeability ◽  
Coarse Aggregate ◽  
Pervious Concrete ◽  
Alkali Activated Slag ◽  
Activated Slag ◽  
Alkali Activated

Pervious concrete is made of cementitious materials, coarse aggregate, water and additives, with characteristic macro- and meso-connected pore structure, which enables the acceptable mechanical properties and high water permeability for pavement and road applications. In this study, the effect of rheology of fresh alkali-activated slag paste on the sedimentation of paste on the bottom of pervious concrete, meso-structure, connected porosity, mechanical properties and water permeability was investigated by a range of analytical techniques through varying the equivalent alkali content to control the rheology of fresh paste in the pervious concrete. The compressive strength of pervious concrete was related to the percentage area of paste and the average thickness of paste on the surface of coarse aggregate. The tensile strength and water permeability were correlated to the connected porosity of pervious concrete and the rheology of fresh paste. A relative lower fluidity, higher viscosity and shear stress of fresh alkali-activated slag paste favoured lower sedimentation of paste on the bottom of pervious concrete, higher connected porosity, tensile strength and water permeability. There was no correlation between compressive strength and tensile strength of pervious concrete.

Effect of Polymer Admixtures on Mechanical Properties of Alkali-Activated Slag Mortars

2015 ◽  
Vol 1124 ◽  
pp. 145-150 ◽  
Author(s):  
Olesia Mikhailova ◽  
Pavel Rovnaník
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Polyethylene Glycol ◽  
Acrylic Acid ◽  
Polypropylene Glycol ◽  
Alkali Activated Slag ◽  
Different Types ◽  
Methyl Metacrylate ◽  
Activated Slag ◽  
Alkali Activated

Alkali-activated slag (AAS) binders have lower environmental impact due to its production process, but also have disadvantages as an increased shrinkage followed by formation of microcracks. The effect of polymer admixtures based on vinyl acetate, ethylene and acrylic acid ester, methyl metacrylate and different types of polyethylene glycol (PEG) and polypropylene glycol (PPG) on properties of alkali-activated slag concrete was studied. Admixtures used for mortars were tested to improve shrinkage, workability and compressive strength, flexural strength. The analysis also showed the effect of the admixtures on microstructure of the alkali-activated slag pastes and mortars.

scholarly journals A Systematic Study on Polymer-Modified Alkali-Activated Slag–Part II: From Hydration to Mechanical Properties

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3418 ◽  
Author(s):  
Zichen Lu ◽  
Jan-Philip Merkl ◽  
Maxim Pulkin ◽  
Rafia Firdous ◽  
Steffen Wache ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Pore Structure ◽  
Analytical Techniques ◽  
Hydration Products ◽  
Ion Diffusion ◽  
X Ray Diffraction ◽  
Alkali Activated Slag ◽  
Activated Slag ◽  
Alkali Activated ◽  
Polymer Latex

The effect of styrene-acrylate (SA) polymer latex on alkali-activated slag (AAS) was systematically studied in the aspects of hydration, hydration products, pore structure and mechanical properties through the combined analytical techniques including calorimetry, X-ray diffraction, thermogravimetric analysis, mercury intrusion porosimetry, and mechanical measurement. It was found that the addition of SA does not retard the AAS hydration, but slightly accelerates it, possibly due to the increasing ion diffusion through the loosely structured hydration products. Pore structure analysis indicates that the addition of polymer increases the cumulative pore volume and the portion of pores with size >100 nm in the hardened AAS paste. The addition of SA latex results in a continuous decrease of the compressive strength, but the flexural strength firstly increases and then decreases with the increase of polymer dosage. The polymer dosage of 2.5 wt % is optimal when applying polymer latex in the AAS system in this study.

scholarly journals Understanding the Role of Metakaolin towards Mitigating the Shrinkage Behavior of Alkali-Activated Slag

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6962
Author(s):  
Bo Fu ◽  
Zhenyun Cheng ◽  
Jingyun Han ◽  
Ning Li
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Drying Shrinkage ◽  
Activator Concentration ◽  
Reaction Products ◽  
Alkali Activated Slag ◽  
Activated Slag ◽  
Alkali Activated ◽  
Shrinkage Behavior

This research investigates the mechanism of metakaolin for mitigating the autogenous and drying shrinkages of alkali-activated slag with regard to the activator parameters, including concentration and modulus. The results indicate that the incorporation of metakaolin can decrease the initial viscosity and setting time. Increasing activator concentration can promote the reaction process and shorten the setting time. An increase in the metakaolin content induces a decrease in compressive strength due to reduced formation of reaction products. However, increasing activator dosage and modulus can improve the compressive strength of alkali-activated slag containing 30% metakaolin. The inclusion of metakaolin can mitigate the autogenous and drying shrinkage of alkali-activated slag by coarsening the pore structure. On the other hand, increases in activator concentration and modulus result in an increase in magnitude of the autogenous and drying shrinkage of alkali-activated slag containing metakaolin. The influence of the activator modulus on the shrinkage behavior of alkali-activated slag-metakaolin binary system should be further investigated.

Sign in / Sign up

Export Citation Format

Share Document