scholarly journals Analysis of Air Flow, Air and Fuel Induction for Internal Combustion Engine

2021 ◽  
Vol 1 (1) ◽  
Author(s):  
Mohd Fitri Arshad ◽  
◽  
Muhammad Faris Ahmad ◽  
Amir Khalid ◽  
Izuan Amin Ishak ◽  
...  
Keyword(s):  
Fluid Flow ◽  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Flow Behavior ◽  
Combustion Process ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Internal Combustion ◽  
Spark Ignition Engine ◽  
Rotating Flow

In an internal combustion engine, performance, efficiency and emission formation depends on the formation of air-fuel mixture inside the engine cylinder. The fluid flow dynamics plays an important role for air-fuel mixture preparation to obtain the better engine combustion, performance and efficiency. This review article discuss the rotating flow (swirl and tumble) in premixed spark-ignition engine and its effect on turbulence generation and flame propagation. Rotating flow can substantially increase turbulence intensity for the duration of the combustion period. This review paper discusses the in-cylinder swirl and tumble flow that affects air induction during the combustion process in internal combustion engine. Alternatively, this study using computer simulation (Computational Fluid Dynamic, CFD) which offer the opportunity to carry out repetitive parameter studies. An integration-type flowmeter (IFM) also has been used which consists of ultrasonic flowmeter, that integrates the flowrate during the intake process, gives accurate measurements regardless of sampling time and frequency. Research parameter in this study was swirl and tumble that represents the fluid flow behavior occurred inside combustion chamber. Fuel injection and air mass also were the important parameters that have been discussed about in air induction process. The results obtain from the numerical analysis can be employed to examine the homogeneity of air-fuel mixture structure for better combustion process and engine performance.

scholarly journals Performance and Exhaust Emissions of a Spark Ignition Internal Combustion Engine Fed with Butanol–Glycerol Blend

Energies ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6473
Author(s):  
Stanislaw Szwaja ◽  
Michal Gruca ◽  
Michal Pyrc ◽  
Romualdas Juknelevičius
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Engine Performance ◽  
Internal Combustion ◽  
Exhaust Emissions ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Spark Ignition Engines ◽  
Exhaust Temperature ◽  
Indicated Mean Effective Pressure

Investigation of a new type of fuel for the internal combustion engine, which can be successfully used in both the power generation and the automotive industries, is presented in this article. The proposed fuel is a blend of 75% n-butanol and 25% glycerol. The engine tests conducted with this glycerol–butanol blend were focused on the performance, combustion thermodynamics, and exhaust emissions of a spark-ignition engine. A comparative analysis was performed to find potential similarities and differences in the engine fueled with gasoline 95 and the proposed glycerol–butanol blend. As measured, CO exhaust emissions increased, NOx emissions decreased, and UHC emissions were unchanged for the glycerol–butanol blend when compared to the test with sole gasoline. As regards the engine performance and combustion progress, no significant differences were observed. Exhaust temperature remarkably decreased by 3.4%, which contributed to an increase in the indicated mean effective pressure by approximately 4% compared to gasoline 95. To summarize, the proposed glycerol–butanol blend can be directly used as a replacement for gasoline in internal combustion spark-ignition engines.

The Destruction of Exergy During the Combustion Process for a Spark-Ignition Engine

2010 ◽  
Author(s):  
Jerald A. Caton
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Combustion Process ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Design Parameters ◽  
Base Case ◽  
Operating Parameters ◽  
Wide Range

The second law of thermodynamics provides the mechanism for assessing the quality of energy. The non-conserved property used for this assessment is called exergy, availability or available energy. For the internal combustion engine, the exergy of the fuel is distributed among work, heat transfer, exhaust, and is destroyed by several processes. The major destruction of exergy for the internal combustion engine is during the combustion process. This paper documents this destruction for a wide range of engine operating parameters, design parameters, and fuels. A 5.7 liter, spark ignition, automotive engine was selected for this study. Operating parameters that were examined included equivalence ratio, speed, load and spark timing. Design parameters that were examined included compression ratio, expansion ratio and the use of turbocharging. Combustion parameters and oxidizer were examined as well. The fuels examined included isooctane (base), methane, propane, hexane, methanol, ethanol, hydrogen and carbon monoxide. For the part load base case (1400 rpm and a bmep of 325 kPa) using isooctane, the destruction of exergy was 21% of the fuel exergy. For many of the engine operating and design parameters, this destruction was relatively constant (between about 20 and 23%). The parameters that resulted in the greatest change of the exergy destruction were (1) exhaust gas recirculation, and (2) inlet oxygen concentration. In general, the amount of the destruction of exergy during the combustion processes was associated with the level of the combustion temperatures.

On the Prediction of Pollutant Emission [NOx] in Internal Combustion Engine

2013 ◽  
Vol 824 ◽  
pp. 505-513
Author(s):  
B.Y. Ogunmola ◽  
S.M. Abolarin ◽  
A.O. Adelaja
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Flame Temperature ◽  
Combustion Process ◽  
Internal Combustion ◽  
Spark Ignition Engine ◽  
Pollutant Emission ◽  
Matlab Simulation ◽  
Combustion Time ◽  
Equilibrium Equations

The study of internal chemical processes involving nitrogenous species forms an important part in the understanding of parameters which lower NOxemission from combustion systems. The focus of this research is to numerically model the prediction of formation of pollutant emission in a continuous internal combustion engine (ICE), from finite rate chemical equilibrium equations. The main source of nitrogen in the chemical formation of NOxis atmospheric, and a very small portion is caused by nitrogen compounds found in some fuels. A mathematical modeling was carried out with these equations using MATLAB simulation to predict the concentration of Nitric Oxide NO; a pollutant, at different flame temperatures and reaction timing of ICE. The temperatures under consideration vary from 1500K to 2300K. The concentration of the pollutant was evaluated by the analytical and numerical methods for a spark ignition engine at a temperature of 2000K; pressure of 1atm, considering a sample containing 78% of Nitrogen and 4% of Oxygen and 78% Nitrogen and 21% Oxygen held between zero to one second in the course of the combustion process, while the computer programme simulated between zero and 100seconds. The concentrations predicted were found to increase as the flame temperature, the combustion time increase as depicted on the results and as the percentage composition of Oxygen in the mixture increases, but reduces with increasing fuel nitrogen content.

scholarly journals The Effect of Compression Ratio by Different Piston Head Shape on the Performance of Motorcycle Engine

2019 ◽  
Vol 16 (3) ◽  
pp. 6906-6917
Author(s):  
A. Katijan ◽  
A. H. Kamardin
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Compression Ratio ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Engine Performance ◽  
Internal Combustion ◽  
Head Shape ◽  
Piston Head

The compression ratio has a significant impact on engine power, fuel economy, emission, and other performances of internal combustion engines. Basic engine theory states that a higher compression ratio produces higher torque and horsepower. One way of having different compression ratio is by changing piston head shape. A piston is a cylindrical engine component that slides back and forth in the cylinder bore via forces produced during the combustion process. The piston acts as a movable end of the combustion chamber transmitting power generated from the burning of fuel and air mixture in the combustion chamber. The objective of this study is to compare the engine performance in horsepower and torque produced by the different shapes of the piston head in an internal combustion engine. Three pistons with different head shapes -  standard, mug (low compression) and dome (high compression) with a compression ratio of 8.8:1, 7.61:1 and 10.06:1 were selected for the study. An experiment was also performed to a standard piston installed with 1.5 mm gasket, which has a compression ratio of 7.31. The experiments were carried out using a standard internal combustion engine of a Honda EX5 motorcycle. The engine runs on a chassis dynamometer to measure its torque and horsepower. Piston performance was evaluated based on the maximum available torque and horsepower. The result shows that all three pistons produce different torque and horsepower. The domed piston head produces higher torque and horsepower followed by the standard and mug. By just changing the piston head shape, torque and horsepower increased up to 7.14% and 20.05%  respectively.

Analysis and Research of the Combustion Process of YN4100QB Diesel Engine

2013 ◽  
Vol 744 ◽  
pp. 35-39
Author(s):  
Lei Ming Shi ◽  
Guang Hui Jia ◽  
Zhi Fei Zhang ◽  
Zhong Ming Xu
Keyword(s):  
Diesel Engine ◽  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Optimization Design ◽  
Combustion Engine ◽  
Geometric Model ◽  
Combustion Process ◽  
Internal Combustion ◽  
Engine Combustion ◽  
Exhaust Noise

In order to obtain the foundation to the research on the Diesel Engine YN4100QB combustion process, exhaust, the optimal design of combustion chamber and the useful information for the design of exhaust muffler, the geometric model and mesh model of a type internal combustion engine are constructed by using FIRE software to analyze the working process of internal combustion engine. Exhaust noise is the main component of automobile noise in the study of controlling vehicle noise. It is primary to design a type of muffler which is good for agricultural automobile engine matching and noise reduction effect. The present car mufflers are all development means. So it is bound to cause the long cycle of product development and waste of resources. Even sometimes not only can it not reach the purpose of reducing the noise but also it leads to reduce the engine dynamic. The strength of the exhaust noise is closely related to engine combustion temperature and pressure. The calculation and initial parameters are applied to the software based on the combustion model and theory. According to the specific operation process of internal combustion engine. Five kinds of common operation condition was compiled. It is obtained for the detailed distribution parameters of combusted gas temperature pressure . It is also got for flow velocity of the fields in cylinder and given for the relation of the parameters and crankshaft angle for the further research. At the same time NOx emissions situation are got. The numerical results show that not only does it provide the 3D distribution data in different crank shaft angle inside the cylinder in the simulation of combustion process, but also it provides a basis for the engine combustion ,emission research, the optimization design of the combustion chamber and the useful information for the designs of muffler.

Effect of Engine Operating Parameters on Combustion and Emission Characteristics

1992 ◽  
Author(s):  
Jiang Lu ◽  
Ashwani K. Gupta ◽  
Eugene L. Keating
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Internal Combustion ◽  
Operating Parameters ◽  
Emission Characteristics ◽  
Pollutants Emission

Abstract Numerical simulation of flow, combustion, heat release rate and pollutants emission characteristics have been obtained using a single cylinder internal combustion engine operating with propane as the fuel. The data are compared with experimental results and show excellent agreement for peak pressure and the rate of pressure rise as a function of crank angle. The results obtained for NO and CO are also found to be in good agreement and are similar to those reported in the literature for the chosen combustion chamber geometry. The results have shown that both the combustion chamber geometry and engine operating parameters affects the flame growth within the combustion chamber which subsequently affects the pollutants emission levels. The code employed the time marching procedure and solves the governing partial differential equations of multi-component chemically reacting fluid flow by finite difference method. The numerical results provide a cost effective means of developing advanced internal combustion engine chamber geometry design that provides high efficiency and low pollution levels. It is expected that increased computational tools will be used in the future for enhancing our understanding of the detailed combustion process in internal combustion engines and all other energy conversion systems. Such detailed information is critical for the development of advanced methods for energy conservation and environmental pollution control.

Ethers and esters as alternative fuels for internal combustion engine: A review

2021 ◽  
pp. 146808742110464
Author(s):  
Yang Hua
Keyword(s):  
Alternative Fuels ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Engine Performance ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Future Research ◽  
Particulate Emissions ◽  
Ic Engine

Ether and ester fuels can work in the existing internal combustion (IC) engine with some important advantages. This work comprehensively reviews and summarizes the literatures on ether fuels represented by DME, DEE, DBE, DGM, and DMM, and ester fuels represented by DMC and biodiesel from three aspects of properties, production and engine application, so as to prove their feasibility and prospects as alternative fuels for compression ignition (CI) and spark ignition (SI) engines. These studies cover the effects of ether and ester fuels applied in the form of single fuel, mixed fuel, dual-fuel, and multi-fuel on engine performance, combustion and emission characteristics. The evaluation indexes mainly include torque, power, BTE, BSFC, ignition delay, heat release rate, pressure rise rate, combustion duration, exhaust gas temperature, CO, HC, NOx, PM, and smoke. The results show that ethers and esters have varying degrees of impact on engine performance, combustion and emissions. They can basically improve the thermal efficiency of the engine and reduce particulate emissions, but their effects on power, fuel consumption, combustion process, and CO, HC, and NOx emissions are uncertain, which is due to the coupling of operating conditions, fuel molecular structure, in-cylinder environment and application methods. By changing the injection strategy, adjusting the EGR rate, adopting a new combustion mode, adding improvers or synergizing multiple fuels, adverse effects can be avoided and the benefits of oxygenated fuel can be maximized. Finally, some challenges faced by alternative fuels and future research directions are analyzed.

3D CFD Simulations of Hydrogen Fuelled Spark Ignition Engine

2008 ◽  
Author(s):  
Dinesh D. Adgulkar ◽  
N. V. Deshpande ◽  
S. B. Thombre ◽  
I. K. Chopde
Keyword(s):  
Internal Combustion Engine ◽  
Power Output ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Flame Speed ◽  
Spark Ignition Engine ◽  
Cfd Simulations ◽  
Turbulent Flame Speed ◽  
Combustion Of Hydrogen

By supporting hydrogen as an alternative fuel to the conventional fuel i.e. gasoline, new era of renewable and carbon neutral energy resources can be introduced. Hence, development of hydrogen fuelled internal combustion engine for improved power density and less emission of NOx has become today’s need and researchers are continuously extending their efforts in the improvement of hydrogen fuelled internal combustion engine. In this work, three dimensional CFD simulations were performed using CFD code (AVL FIRE) for premixed combustion of hydrogen. The simplified 3D geometry of engine with single valve i.e. inlet valve was considered for the simulation. Various combustion models for spark ignition for hydrogen i.e. Eddy Breakup model, Turbulent Flame Speed Closure Combustion Model, Coherent Flame model, Probability Density Function model were tested and validated with available simulation results. Results obtained in simulation indicate that the properties of hydrogen i.e. high flame speed, wide flammability limit, and high ignition temperature are among the main influencing factors for hydrogen combustion being different than that of gasoline. Different parameters i.e. spark advance angle (TDC to 40° before TDC in the step of 5°), rotational speed (1200 to 3000 rpm in the step of 300 rpm), equivalence ratio (0.5 to 1.2 in the step of 0.1), and compression ratio (8, 9 and 10) were used to simulate the combustion of hydrogen in spark ignition engine and to investigate their effects on the engine performance, which is in terms of pressure distribution, temperature distribution, species mass fraction, reaction progress variable and rate of heat release for complete cycle. The results of power output for hydrogen were also compared with that of gasoline. It has been observed that power output for hydrogen is almost 12–15% less than that of gasoline.

scholarly journals Assessment of thermodynamic cycle of internal combustion engine in terms of rightsizing

2019 ◽  
Vol 178 (3) ◽  
pp. 182-186
Author(s):  
Zbigniew SROKA ◽  
Maciej DWORACZYŃSKI
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Thermodynamic Cycle ◽  
Internal Combustion ◽  
Research Problem ◽  
Combustion Engines ◽  
Operating Characteristics ◽  
Swept Volume

The modification of the downsizing trend of internal combustion engines towards rightsizing is a new challenge for constructors. The change in the displacement volume of internal combustion engines accompanying the rightsizing idea may in fact mean a reduction or increase of the defining swept volume change factors and thus may affect the change in the operating characteristics as a result of changes in combustion process parameters - a research problem described in this publication. Incidents of changes in the displacement volume were considered along with the change of the compression space and at the change of the geometric degree of compression. The new form of the mathematical dependence describing the efficiency of the thermodynamic cycle makes it possible to evaluate the opera-tion indicators of the internal combustion engine along with the implementation of the rightsizing idea. The work demonstrated the in-variance of cycle efficiency with different forms of rightsizing.

Improved throttle valve modeling for spark-ignition engine simulations

2018 ◽  
Vol 233 (6) ◽  
pp. 1614-1622 ◽  
Author(s):  
Elie Haddad ◽  
David Chalet ◽  
Pascal Chesse
Keyword(s):  
Internal Combustion Engine ◽  
Discharge Coefficient ◽  
Test Bench ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Simulation Software ◽  
Spark Ignition Engine ◽  
Engine Test ◽  
Engine Simulation ◽  
Throttle Valve

Automotive manufacturers nowadays are constantly working on improving their internal combustion engines’ performance by reducing the fuel consumption and emissions, without compromising the power generated. Manufacturers are therefore relying on virtual engine models that can be run on simulation software in order to reduce the amount of time and costs needed, in comparison with experiments done on engine test benches. One important element of the intake system of an internal combustion engine is the throttle valve, which defines the amount of air reaching the plenum before being drawn into the cylinders. This article discusses a widely used model for the estimation of air flow rate through the throttle valve in an internal combustion engine simulation. Experiments have been conducted on an isolated throttle valve test bench in order to understand the influence of different factors on the model’s discharge coefficient. These experiments showed that the discharge coefficient varies with the pressure ratio across the throttle valve and with its angle. Furthermore, for each angle, this variation can be approximated with a linear model composed of two parameters: the slope and the Y-Intercept. These parameters are calibrated for different throttle valve angles. This calibration can be done using automotive manufacturers’ standard engine test fields that are often available. This model is then introduced into an engine simulation model, and the results are compared to the experimental data of a turbocharged engine test bench for validation. They are also compared with a standard discharge coefficient model that varies only with the throttle valve angle. The results show that the new model for the discharge coefficient reduces mass flow estimation errors and allows expanding the applications of the throttle valve isentropic nozzle model.

Sign in / Sign up

Export Citation Format

Share Document