scholarly journals Engine performance of blends of palm kernel oil biodiesel under varying speed at constant torque

2020 ◽  
Vol 39 (3) ◽  
pp. 761-766
Author(s):  
J.N. Nwakaire ◽  
O.F. Obi ◽  
C.J. Ohagwu ◽  
C.C. Anyadike ◽  
I.E. Ugwu ◽  
...  
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Palm Kernel ◽  
Engine Performance ◽  
Biofuel Production ◽  
Brake Thermal Efficiency ◽  
Kernel Oil ◽  
Constant Torque ◽  
Consumption Rates ◽  
Test Fuel

This study conducts a comparative evaluation the effect of using palm kernel oil (PKO), pure petroleum diesel and their blends (B5, B10, B20, B30, B40, and B100), on the performance of a four-cylinder CI diesel engine (David Brown 990: 58hp; 2WD), at Farm Power and Machinery Test laboratory Centre (FPMTLC), Department of Agricultural and Bioresources Engineering, University of Nigeria, Nsukka. The objective of the study was to determine the fuel consumption rates, energy expended, brake specific fuel consumption, and brake thermal efficiency, under varying operating speeds (700 – 1900rpm) at constant torque. Each fuel test was conducted using the Heenan-Froude hydraulic dynamometer engine-test-bed; pure petroleum diesel (B0) was used to generate the baseline data. Variables calculated were analyzed, then compared with each other to determine the differences in the engine performance and also to determine the optimum test fuel. The results obtained show that B10 had the overall optimum energy output, fuel consumption rates, and brake specific fuel consumption of 5431.809J, 3.42E-07 m3/s, and 0.16569l/KWh, respectively at the highest engine speed of 1900. B10 had an excellent brake thermal efficiency of 60.6% but was not better than B100, which showed a higher value of 66.95%. From the analysis, B10 is the optimum test fuel and can be used as an alternative fuel in David Brown 990 (58hp; 2WD) or similar CI diesel engines without any engine modification, even though B100 showed potential as an alternative to fossil diesel. Biofuel production grows through integrated aquaculture and algae production; the algae oil will serve as a raw material for biofuel production Keywords: Blends, Biodiesel, Brake Specific Consumption, Diesel Engine, Fuel Consumption rate, Thermal Efficiency.

scholarly journals Comprehensive Assessment from Optimum Biodiesel Yield to Combustion Characteristics of Light Duty Diesel Engine Fueled with Palm Kernel Oil Biodiesel and Fuel Additives

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4274
Author(s):  
Senthur Prabu Sabapathy ◽  
Asokan Morappur Ammasi ◽  
Esmail Khalife ◽  
Mohammad Kaveh ◽  
Mariusz Szymanek ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Palm Kernel ◽  
Yield Condition ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Brake Thermal Efficiency ◽  
Palm Kernel Oil ◽  
Kernel Oil

Biodiesel is considered as a key prospective renewable energy source in India. Hence, a study was carried out for the improvement of palm kernel oil biodiesel production using a transesterification process at different molar ratios. This study comprehensively examined all aspects of biodiesel from optimum production to the effect of additives on its combustion behavior. The optimum yield condition was validated with the MINITAB-17 software and analyzed using the Taguchi method. Two different additives, 5% diethyl ether (DEE) and 2000 ppm Butylated hydroxyltoluene (BHT), were also experimented. Engine experiments were conducted at constant speed (1500 rpm) and five different engine loads (0, 25, 50, 75 and 100%) on a single-cylinder direct injection diesel engine. Heat release rate, brake specific fuel consumption, brake thermal efficiency, engine emissions, such as CO, HC, NOx, and smoke opacity were analyzed. The maximum palm kernel oil (PKO) biodiesel yields, obtained at 55 °C, for the KOH and NaOH catalysts were 86.69% and 75.21% at the molar ratio of 6:1. B20BHT combustion showed 4.6% higher brake thermal efficiency (BTE). NOx emission was reduced by 19.4%, compared to the diesel fuel values. DEE resulted in higher CO and HC emissions compared to diesel fuel values by 39.2% and 7.6%, respectively, whereas smoke emission was improved by 11.5%.

scholarly journals The experimental investigation of diesel fuel-biofuel blends at different injection pressures in a DI diesel engine

2021 ◽  
Vol 9 (4A) ◽  
Author(s):  
İlker Örs ◽  
◽  
Murat Ciniviz ◽  
Bahar Sayin Kul ◽  
Ali Kahraman ◽  
...  
Keyword(s):  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Engine Performance ◽  
Injection Pressure ◽  
Exhaust Emissions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Injection Pressures

In this study, it was aimed to investigate the effects of a diesel-biodiesel blend (B20) and a diesel-biodiesel-bioethanol blend (BE5) on combustion parameters in addition to engine performance and exhaust emissions compared with diesel fuel. Parameters included in the evaluation was brake specific fuel consumption, brake thermal efficiency, CO, CO2, HC, NOx, smoke opacity emissions and finally cylinder pressure, heat release rate, ignition delay, some key points of the combustion phases such as start of ignition, start of combustion, CA50 and CA90 and combustion duration. Engine tests were conducted at different injection pressures of 170 bar, 190 bar, which is the original injection pressure, and 220 bar by the engine being loaded by 25, 50, 75 and 100% for the assessment of engine performance and exhaust emissions. For combustion evaluation, the data obtained at 1400 rpm, maximum torque-speed, and 2800 rpm, maximum power-speed were used, while the injection pressures were set to 170, 190 and 220 bar under full load condition. According to test results, the better performance characteristics, exhaust emissions and combustion behaviour of engine were obtained with the use of BE5 at high injection pressure. So, BE5 fuel improved brake specific fuel consumption by about 7% and brake thermal efficiency by about 6% compared to B20. In addition, while the emission values of BE5 gave better results than diesel fuel, it reduced the NOx and smoke emissions of B20 by approximately 1.4% and 6.4% respectively. Moreover, it has achieved a reduction in smoke emission of up to 45% compared to diesel fuel.

scholarly journals Effects of Methyl Acetate as Oxygenated Fuel Blending on Performance and Emissions of SI Engine

2018 ◽  
Vol 22 (1) ◽  
pp. 55-68 ◽  
Author(s):  
Abdulvahap Cakmak ◽  
Murat Kapusuz ◽  
Orkhan Ganiyev ◽  
Hakan Ozcan
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Methyl Acetate ◽  
Engine Performance ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Si Engine ◽  
Brake Thermal Efficiency ◽  
Oxygenated Fuel ◽  
Fuel Blending

Abstract - The objective of this paper is to investigate the use of methyl acetate as oxygenated fuel blending for base gasoline in SI engine. The effects of methyl acetate on engine performance parameters (brake specific fuel consumption, brake thermal efficiency and energy consumption rate) and exhaust emissions (CO, HC, CO2 and NOx) of SI engine have been experimentally investigated. Engine experiments were conducted on a single cylinder, water cooled, spark-ignition test engine at constant moderate speed; 1500 rpm for different loads; 104, 207, 311 and 414 kPa fuelling the engine with base gasoline, M5 (95 % base gasoline +5 % methyl acetate) and M10 (90 % base gasoline +10 % methyl acetate). The results showed that adding methyl acetate to base gasoline increases the brake specific fuel consumption while reducing the brake thermal efficiency of the engine. Furthermore, it was also observed that methyl acetate addition does not have a great effect on HC emissions, however, reduces CO and increases CO2 emissions. NOx results showed a striking increase in the level of NOx emissions with the addition of methyl acetate.

scholarly journals Control of Exhaust Emissions Using Piston Coating on Two-StrokeSI Engines with Gasoline Blends

2021 ◽  
Vol 8 (1) ◽  
pp. H16-H20
Author(s):  
A.V.N.S. Kiran ◽  
B. Ramanjaneyulu ◽  
M. Lokanath M. ◽  
S. Nagendra ◽  
G.E. Balachander
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Specific Fuel Consumption ◽  
Thermal Barrier ◽  
Piston Crown ◽  
Barrier Coating

An increase in fuel utilization to internal combustion engines, variation in gasoline price, reduction of the fossil fuels and natural resources, needs less carbon content in fuel to find an alternative fuel. This paper presents a comparative study of various gasoline blends in a single-cylinder two-stroke SI engine. The present experimental investigation with gasoline blends of butanol and propanol and magnesium partially stabilized zirconium (Mg-PSZ) as thermal barrier coating on piston crown of 100 µm. The samples of gasoline blends were blended with petrol in 1:4 ratios: 20 % of butanol and 80 % of gasoline; 20 % of propanol and 80 % of gasoline. In this work, the following engine characteristics of brake thermal efficiency (BTH), specific fuel consumption (SFC), HC, and CO emissions were measured for both coated and non-coated pistons. Experiments have shown that the thermal efficiency is increased by 2.2 % at P20. The specific fuel consumption is minimized by 2.2 % at P20. Exhaust emissions are minimized by 2.0 % of HC and 2.4 % of CO at B20. The results strongly indicate that the combination of thermal barrier coatings and gasoline blends can improve engine performance and reduce exhaust emissions.

scholarly journals EXPERIMENTAL ANALYSIS OF THE COMBUSTION CHAMBER COATED WITH Mo AND Al2O3-TiO2 IN A DIESEL ENGINE

2021 ◽  
Vol 55 (4) ◽  
Author(s):  
Murugan Kuppusamy ◽  
Thirumalai Ramanathan ◽  
Udhayakumar Krishnavel ◽  
Seenivasan Murugesan
Keyword(s):  
Combustion Chamber ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Performance Test ◽  
Ceramic Powder ◽  
Specific Fuel Consumption ◽  
Emission Characteristic ◽  
Powder Materials ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency

The effect of thermal-barrier coatings (TBCs) reduces fuel consumption, effectively improving the engine efficiency. This research focused on a TBC with a thickness of 300 µm insulating the combustion chamber of a direct ignition (DI) engine. The piston crown, inlet and exhaust-valve head were coated using air-plasma-spray coating. Ceramic powder materials such as molybdenum (Mo) and aluminum oxide titanium dioxide (Al2O3-TiO2) were used. A performance test of the engine with the coated combustion chamber was carried out to investigate the brake power, brake thermal efficiency, volumetric efficiency, brake specific fuel consumption and air-fuel ratio. Also, an emission-characteristic test was carried out to investigate the emissions of unburned hydrocarbon (HC), carbon monoxide (CO), nitrogen oxides (NO, NO2, NO3) and smoke opacity (SO). The results reveal that the brake thermal efficiency and brake specific fuel consumption show significant increases because of these coating materials. The effect of the Al2O3-TiO2 coating significantly reduces the HC and CO engine emissions.

Impact of Oxidation Inhibitors on Performance and Emission Characteristics of a Low Heat Rejection Engine

2017 ◽  
Vol 8 (4) ◽  
Author(s):  
P.S. Kumar ◽  
S.A. Kannan ◽  
A. Kumar ◽  
K.A.V. Geethan
Keyword(s):  
Combustion Chamber ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Specific Fuel Consumption ◽  
Nox Emission ◽  
Emission Characteristics ◽  
Brake Thermal Efficiency ◽  
Heat Rejection ◽  
Oxidation Inhibitors ◽  
Low Heat Rejection Engine

In this study, for the first time analysis of a low heat rejection engine was carried out along with the addition of oxidation inhibitors. If the combustion chamber components of the engine such as piston, cylinder head, and inlet and outlet valves are insulated with a thermal barrier material, then the engine will be referred as low heat rejection engine. In this study yttria stabilized zirconia was coated on the combustion chamber components for a thickness of about 150 microns. Then the analysis of performance parameters such as brake thermal efficiency and specific fuel consumption and emission characteristics such as emission of carbon monoxide, hydrocarbon and nitrogen oxide was carried out in single cylinder four stroke diesel engine with electrical loading using diesel and pongamia methyl ester as the fuels. The major problem associated with the usage of biodiesels and low heat rejection engine is the increased NOX emission than the normal engine operated with the diesel. This problem has been overcome by the usage of oxidation inhibitors such as ethyl hexyl nitrate (EHN), tert-butyl hydroquinone (TBHQ). The results showed that addition of oxidation inhibitors leads to increase in brake thermal efficiency, reduced specific fuel consumption and reduced NOX emission.

Application of Over-Expansion Cycle to a Larger Gasoline Engine With Late-Closing of Intake Valves

2002 ◽  
Author(s):  
Seiichi Shiga ◽  
Kenji Nishida ◽  
Shizuo Yagi ◽  
Youichi Miyashita ◽  
Yoshiharu Yuzawa ◽  
...  
Keyword(s):  
Compression Ratio ◽  
Thermal Efficiency ◽  
Gasoline Engine ◽  
Engine Performance ◽  
Mechanical Efficiency ◽  
Expansion Ratio ◽  
Brake Thermal Efficiency ◽  
Gasoline Engines ◽  
Cylinder Test ◽  
Test Engine

This paper presents further investigation into the effect of over-expansion cycle with late-closing of intake valves on the engine performance in gasoline engines. A larger single-cylinder test engine with the stroke volume of 650 cc was used with four kinds of expansion ratio (geometrical compression ratio) from 10 to 25 and four sets of intake valve closure (I.V.C.) timings from 0 to 110 deg C.A. ABDC. Late-closing has an effect of decreasing the pumping work due to the reduction of intake vacuum, althogh higher expansion ratio increases the friction work due to the average cylinder pressure level. Combining the higher expansion ratio with the late-closing determines the mechanical efficiency on the basis of these two contrastive effects. The indicated thermal efficiency is mostly determined by the expansion ratio and little affected by the nominal compression ratio. The value of the indicated thermal efficiency reaches to 48% at most which is almost comparable with the value of diesel engines. The improvement of both indicated and brake thermal efficiency reaches to 16% which is much higher than ever reported by the authors. A simple thermodynamic calculation could successfully explain the behavior of the indicated thermal efficiency. The brake thermal efficiency could also be improved due to the increase in both mechanical and indicated efficiencies.

The Comparative Trail Research on the Performance of a Diesel Engine Fuelled with Diesel Fuel and Biodiesel/Diesel Blended Fuel

2011 ◽  
Vol 142 ◽  
pp. 103-106
Author(s):  
Wen Ming Cheng ◽  
Hui Xie ◽  
Gang Li
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Series Of Experiments ◽  
Blended Fuel ◽  
Load Conditions

This paper discusses the brake specific fuel consumption and brake thermal efficiency of a diesel engine using cottonseed biodiesel blended with diesel fuel. A series of experiments were conducted for the various blends under varying load conditions at a speed of 1500 rpm and 2500 rpm and the results were compared with the neat diesel. From the results, it is found that the brake specific fuel consumption of cottonseed biodiesel is slightly higher than that of diesel fuel at different engine loads and speeds, with this increase being higher the higher the percentage of the biodiesel in the blend. And the brake thermal efficiency of cottonseed biodiesel is nearly similar to that of diesel fuel at different engine loads and speeds. From the investigation, it is concluded that cottonseed biodiesl can be directly used in diesel engines without any modifications, at least in small blending ratios.

scholarly journals A Review of Comparative Study on The Effect of Hydroxyl Gas in Internal Combustion Engine (ICE) On Engine Performance and Exhaust Emission

2021 ◽  
Vol 87 (2) ◽  
pp. 1-16
Author(s):  
Amir Ridhuan ◽  
Shahrul Azmir Osman ◽  
Mas Fawzi ◽  
Ahmad Jais Alimin ◽  
Saliza Azlina Osman
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Engine Performance ◽  
Internal Combustion ◽  
Exhaust Emission ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Complete Combustion ◽  
Brake Power

This introductory study comes up with an innovative idea of using Hydroxyl gas as a fuel performance enhancer to reduce the natural sources and the overuse of fossil fuel resulting in increased pollution levels. Many researchers have used HHO gas to analyze gasoline and diesel in internal combustion engines. The main challenges of using HHO gas in engines have been identified as system complexity, safety, cost, and electrolysis efficiency. This article focuses on different performance reports and the emission characteristics of a compression ignition engine. As opposed to general diesel, this study found that using HHO gas improved brake power and torque. In all cases, an increase in braking thermal efficiency can be observed. This was due to the presence of hydrogen in HHO gas with higher calorific value than fossil fuels. At the same time, the fuel consumption unit of the engine was reduced, and the combined impact of hydrogen and oxygen helped to achieve complete combustion and improved the combustion capacity of the fuel when HHO gas was injected. The addition of HHO gas also improved the Brake Power (BP), Brake Torque (BT), Brake Specific Fuel Consumption (BSFC), and thermal efficiency while simultaneously reducing CO and HC formation. The rise in CO2 emissions represented the completion of combustion. Therefore, the usage of HHO gas in the Compression Ignition (CI) engine improved the engine performance and exhaust emissions.

scholarly journals Performance and emissions of a single cylinder diesel engine operating with rapeseed oil and jp-8 fuel blends

2015 ◽  
Vol 162 (3) ◽  
pp. 13-18
Author(s):  
Gvidonas Labeckas ◽  
Irena Kanapkienė
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Rapeseed Oil ◽  
Jet Fuel ◽  
Brake Specific Fuel Consumption ◽  
Test Results ◽  
Brake Thermal Efficiency ◽  
Engine Load ◽  
Fuel Blends

The article presents experimental test results of a DI single-cylinder, air-cooled diesel engine FL 511 operating with the normal (class 2) diesel fuel (DF), rapeseed oil (RO) and its 10%, 20% and 30% (v/v) blends with aviation-turbine fuel JP-8 (NATO code F-34). The purpose of the research was to analyse the effects of using various rapeseed oil and jet fuel RO90, RO80 and RO70 blends on brake specific fuel consumption, brake thermal efficiency, emissions and smoke of the exhaust. The test results of engine operation with various rapeseed oil and jet fuel blends compared with the respective parameters obtained when operating with neat rapeseed oil and those a straight diesel develops at full (100%) engine load and maximum brake torque speed of 2000 rpm. The research results showed that jet fuel added to rapeseed oil allows to decrease the value of kinematic viscosity making such blends suitable for the diesel engines. Using of rapeseed oil and jet fuel blends proved themselves as an effective measure to maintain fuel-efficient performance of a DI diesel engine. The brake specific fuel consumption decreased by about 6.1% (313.4 g/kW·h) and brake thermal efficiency increase by nearly 1.0% (0.296) compared with the respective values a fully (100%) loaded engine fuelled with pure RO at the same test conditions. The maximum NOx emission was up to 13.7% higher, but the CO emissions and smoke opacity of the exhaust 50.0% and 3.4% lower, respectively, for the engine powered with biofuel blend RO70 compared with those values produced by the combustion of neat rapeseed oil at full (100%) engine load and speed of 2000 rpm.

Sign in / Sign up

Export Citation Format

Share Document