scholarly journals Performance evaluation of monocrystalline and polycrystalline silicon solar photovoltaic modules under low and high irradiance conditions in Kumasi, Ghana

2021 ◽  
Vol 40 (3) ◽  
pp. 414-426
Author(s):  
G. Takyi ◽  
A.S. Adunyah ◽  
A. Agyei-Agyemang
Keyword(s):  
Output Power ◽  
Polycrystalline Silicon ◽  
Maximum Output Power ◽  
High Irradiance ◽  
Electrical Performance ◽  
Energy Output ◽  
Maximum Output ◽  
Solar Photovoltaic ◽  
Mesh Screen ◽  
Pv Modules

One of the biggest drawbacks of photovoltaic (PV) for many applications is the uncertainty in the energy output due to losses attributed to efficiency loss at low irradiance levels. In this study, the electrical performance of as received monocrystalline silicon (mono-c-Si) and polycrystalline silicon (poly-c-Si) PV modules were evaluated at high and low irradiance conditions in Kumasi, Ghana using I-V Tracer. The low irradiance level of 200W/m2 was achieved by covering the surface of the PV modules with a calibrated mesh screen. Maximum output power (Pmax) of 87.9 W and 136.7 W were recorded for the mono-c-Si and poly-c-Si modules at high irradiance respectively. The corresponding average values at low irradiance were 8.29 W and 12.13 W representing percentage reductions of 90.57% and 91.60% respectively for the two technologies. These results indicate that when irradiance drops to 200 W/m2 and below, the PV modules generate around only 10% of their nominal output power. This has implications for the number of modules that are required for installation in areas that experience many hours of low irradiance. Efficiency reductions of 64.4% and 59.01% for the mono-c-Si and poly-c-Si modules respectively at low irradiance is reported. The results also indicate that the mono-c-Si is affected more by light induced degradation effect than the poly-c-Si module after a few hours of exposure to the natural light. The novelty of this work is that knowledge of the performance at low irradiance will enable designers determine the number of modules required during the sizing of PV plants.

scholarly journals Power Enhancement from Solar PV Array Topologies under Partial Shading Condition

2018 ◽  
Vol 10 (01) ◽  
pp. 33-40
Author(s):  
Santosh Kumar Singh ◽  
Anurag Singh Yadav ◽  
Ashutosh Srivastava ◽  
Amarjeet Singh
Keyword(s):  
Maximum Output Power ◽  
Maximum Output ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
Partial Shading ◽  
Pv Array ◽  
Power Enhancement ◽  
Pv Modules ◽  
Multiple Load ◽  
Mismatch Effect

In this paper, a detailed study is carried out on the solar photovoltaic (PV) array topologies under various shading patterns. The aim of this study is to investigate the mismatch effect losses in PV modules for non uniform irradiations. The shading causes not only power losses, but also non-linearity of P-V characteristics. Under partial shaded conditions, the P-V and I-V characteristics exhibit extreme non-linearity along with multiple load maxima. In this paper, the investigations of the optimal layout of PV modules in a PV array are worked out to provide maximum output power under various shaded conditions. Three type of solar PV array topologies e.g. Series-parallel (SP), Total cross tied (TCT) and Bridge link (BL) are considered for various typesof shaded patterns. The modeling of solar PV array for various types of topologies is done in MATLAB/Simulink environment. The extensive results have been taken on these topologies for partial shading patterns and analyzed, which proves the TCT topology performance is better as compared to other topologies for most of the shading patterns.

Power Enhancement from Solar PV Array Topologies under Partial Shading Condition

2018 ◽  
Vol 10 (1) ◽  
Author(s):  
Santosh Kumar Singh ◽  
Anurag Singh Yadav ◽  
Ashutosh Srivastava ◽  
Amarjeet Singh
Keyword(s):  
Maximum Output Power ◽  
Maximum Output ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
Partial Shading ◽  
Pv Array ◽  
Power Enhancement ◽  
Pv Modules ◽  
Multiple Load ◽  
Mismatch Effect

In this paper, a detailed study is carried out on the solar photovoltaic (PV) array topologies under various shading patterns. The aim of this study is to investigate the mismatch effect losses in PV modules for non uniform irradiations. The shading causes not only power losses, but also non-linearity of P-V characteristics. Under partial shaded conditions, the P-V and I-V characteristics exhibit extreme non-linearity along with multiple load maxima. In this paper, the investigations of the optimal layout of PV modules in a PV array are worked out to provide maximum output power under various shaded conditions. Three type of solar PV array topologies e.g. Series-parallel (SP), Total cross tied (TCT) and Bridge link (BL) are considered for various types of shaded patterns. The modeling of solar PV array for various types oopologies is done in MATLAB/Simulink environment. The extensive results have been taken on these topologies for partial shading patterns and analyzed, which proves the TCT topology performance is better as compared to other topologies for most of the shading patterns.

scholarly journals Evaluation of Interconnection Configuration Schemes for PV Modules with Switched-Inductor Converters under Partial Shading Conditions

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2802 ◽  
Author(s):  
Kamran Ali Khan Niazi ◽  
Yongheng Yang ◽  
Mashood Nasir ◽  
Dezso Sera
Keyword(s):  
Output Power ◽  
Maximum Output Power ◽  
Research Work ◽  
Maximum Output ◽  
Power Losses ◽  
Comparative Performance ◽  
Partial Shading ◽  
Power Characteristics ◽  
Pv Array ◽  
Pv Modules

Partial shading on photovoltaic (PV) arrays reduces the overall output power and causes multiple maximas on the output power characteristics. Due to the introduction of multiple maximas, mismatch power losses become apparent among multiple PV modules. These mismatch power losses are not only a function of shading characteristics, but also depend on the placement and interconnection patterns of the shaded modules within the array. This research work is aimed to assess the performance of 4 × 4 PV array under different shading conditions. The desired objective is to attain the maximum output power from PV modules at different possible shading patterns by using power electronic-based differential power processing (DPP) techniques. Various PV array interconnection configurations, including the series-parallel (SP), total-cross-tied (TCT), bridge-linked (BL), and center-cross-tied (CCT) are considered under the designed shading patterns. A comparative performance analysis is carried out by analyzing the output power from the DPP-based architecture and the traditional Schottky diode-based architecture. Simulation results show the gain in the output power by using the DPP-based architecture in comparison to the traditional bypassing diode method.

scholarly journals One-Step Preparation of Biochar Electrodes and Their Applications in Sediment Microbial Electrochemical Systems

Catalysts ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 508
Author(s):  
Kui You ◽  
Zihan Zhou ◽  
Chao Gao ◽  
Qiao Yang
Keyword(s):  
Output Power ◽  
Electrode Materials ◽  
Maximum Output Power ◽  
Composite Cathode ◽  
Maximum Output ◽  
Electrochemical Systems ◽  
Composite Cathodes ◽  
One Step ◽  
Microbial Electrochemical Systems ◽  
Hot Melt

Biochar is a kind of carbon-rich material formed by pyrolysis of biomass at high temperature in the absence or limitation of oxygen. It has abundant pore structure and a large surface area, which could be considered the beneficial characteristics for electrodes of microbial electrochemical systems. In this study, reed was used as the raw material of biochar and six biochar-based electrode materials were obtained by three methods, including one-step biochar cathodes (BC 800 and BC 700), biochar/polyethylene composite cathodes (BP 5:5 and BP 6:4), and biochar/polyaniline/hot-melt adhesive composite cathode (BPP 5:1:4 and BPP 4:1:5). The basic physical properties and electrochemical properties of the self-made biochar electrode materials were characterized. Selected biochar-based electrode materials were used as the cathode of sediment microbial electrochemical reactors. The reactor with pure biochar electrode (BC 800) achieves a maximum output power density of 9.15 ± 0.02 mW/m2, which increases the output power by nearly 80% compared with carbon felt. When using a biochar/polyaniline/hot-melt adhesive (BPP 5:1:4) composite cathode, the output power was increased by 2.33 times. Under the premise of ensuring the molding of the material, the higher the content of biochar, the better the electrochemical performance of the electrodes. The treatment of reed powder before pyrolysis is an important factor for the molding of biochar. The one-step molding biochar cathode had satisfactory performance in sediment microbial electrochemical systems. By exploring the biochar-based electrode, waste biomass could be reused, which is beneficial for the environment.

scholarly journals Study of the Properties of a Hybrid Piezoelectric and Electromagnetic Energy Harvester for a Civil Engineering Low-Frequency Sloshing Environment

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 391
Author(s):  
Nan Wu ◽  
Yuncheng He ◽  
Jiyang Fu ◽  
Peng Liao
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Civil Engineering ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electromagnetic Energy ◽  
Maximum Output ◽  
Piezoelectric Film ◽  
Hybrid Energy ◽  
Level Height

In this paper a novel hybrid piezoelectric and electromagnetic energy harvester for civil engineering low-frequency sloshing environment is reported. The architecture, fabrication and characterization of the harvester are discussed. The hybrid energy harvester is composed of a permanent magnet, copper coil, and PVDF(polyvinylidene difluoride) piezoelectric film, and the upper U-tube device containing a cylindrical fluid barrier is connected to the foundation support plate by a hinge and spring. The two primary means of energy collection were through the vortex street, which alternately impacted the PVDF piezoelectric film through fluid shedding, and the electromotive force (EMF) induced by changes in the magnetic field position in the conducting coil. Experimentally, the maximum output power of the piezoelectric transformer of the hybrid energy harvester was 2.47 μW (circuit load 270 kΩ; liquid level height 80 mm); and the maximum output power of the electromagnetic generator was 2.72 μW (circuit load 470 kΩ; liquid level height 60 mm). The low-frequency sloshing energy collected by this energy harvester can drive microsensors for civil engineering monitoring.

LD-pumped high-power continuous-wave Pr3+:YLF deep red lasers at 718.5 and 720.8 nm

Laser Physics ◽  
2021 ◽  
Vol 32 (2) ◽  
pp. 025801
Author(s):  
Xiangrui Liu ◽  
Zhuang Li ◽  
Chengkun Shi ◽  
Bo Xiao ◽  
Run Fang ◽  
...  
Keyword(s):  
Output Power ◽  
High Power ◽  
Slope Efficiency ◽  
Laser Emission ◽  
Continuous Wave ◽  
Optical Glass ◽  
Maximum Output Power ◽  
Glass Plate ◽  
Maximum Output ◽  
First Time

Abstract We demonstrated 22 W LD-pumped high-power continuous-wave (CW) deep red laser operations at 718.5 and 720.8 nm based on an a-cut Pr3+:YLF crystal. The output power of both polarized directions reached the watt-level without output power saturation. A single wavelength laser operated at 720.8 nm in the π-polarized direction was achieved, with a high output power of 4.5 W and high slope efficiency of approximately 41.5%. To the best of our knowledge, under LD-pumped conditions, the laser output power and slope efficiency are the highest at 721 nm. By using a compact optical glass plate as an intracavity etalon, we suppressed the π-polarized 720.8 nm laser emission. And σ-polarized single-wavelength laser emission at 718.5 nm was achieved, with a maximum output power of 1.45 W and a slope efficiency of approximately 17.8%. This is the first time that we have achieved the σ-polarized laser emission at 718.5 nm generated by Pr3+:YLF lasers.

Design and Analysis of a High Power Density, Low Temperature Waste Heat Recovery System Using an Oil-Free Turboalternator

2010 ◽  
Author(s):  
James F. Walton ◽  
Andrew Hunsberger ◽  
Hooshang Heshmat
Keyword(s):  
Output Power ◽  
Waste Heat ◽  
Maximum Output Power ◽  
Output Power Level ◽  
Working Fluid ◽  
Prototype System ◽  
Low Grade ◽  
Maximum Output ◽  
Test Results ◽  
Study Results

In this paper the authors will present the design and preliminary test results for a distributed electric generating system that uses renewable energy source for economical load-following and peak-shaving capability in an oil-free, high-speed micro-turboalternator system using compliant foil bearings and a permanent magnet alternator. Test results achieved with the prototype system operating to full speed and under power generating mode will be presented. A comparison between predicted and measured electrical output will also be presented up to a power generating level of 25 kWe at approximately 55,000 rpm. The excellent correlation between design and test provides the basis for scale up to larger power levels. Based upon the turboalternator test results a thermodynamic cycle analysis of a system using low grade waste heat water at approximately 100 C will be reviewed. The tradeoff study results for a series of environmentally friendly refrigerant working fluids will also be presented including sensitivity to vaporization and condensing temperatures. Based on the cycle and pinch point analyses predicted maximum output power was determined. Finally a preliminary turbine design for the selected R134a working fluid was completed. The results of this study show that a net output power level of greater than 40 kW is possible for approximately 240 l/m flow of water at 100C is possible.

Modelling of Mechanical Nonlinearity in an Electromagnetic Vibration Energy Harvester Using a Forced Duffing Equation

2012 ◽  
Author(s):  
S. D. Moss ◽  
L. A. Vandewater ◽  
S. C. Galea
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Duffing Oscillator ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Homotopy Analysis ◽  
Wire Coil

This work reports on the modelling and experimental validation of a bi-axial vibration energy harvesting approach that uses a permanent-magnet/ball-bearing arrangement and a wire-coil transducer. The harvester’s behaviour is modelled using a forced Duffing oscillator, and the primary first order steady state resonant solutions are found using the homotopy analysis method (or HAM). Solutions found are shown to compare well with measured bearing displacements and harvested output power, and are used to predict the wideband frequency response of this type of vibration energy harvester. A prototype harvesting arrangement produced a maximum output power of 12.9 mW from a 12 Hz, 500 milli-g (or 4.9 m/s2) rms excitation.

scholarly journals Continuous-Wave and Passively Q-Switched Er:Y2O3 Ceramic Laser at 2.7 μm

2018 ◽  
Vol 2018 ◽  
pp. 1-5 ◽  
Author(s):  
Zhipeng Qin ◽  
Guoqiang Xie ◽  
Jian Zhang ◽  
Jingui Ma ◽  
Peng Yuan ◽  
...  
Keyword(s):  
Output Power ◽  
Continuous Wave ◽  
Maximum Output Power ◽  
Maximum Output ◽  
Average Output ◽  
Semiconductor Saturable Absorber ◽  
Infrared Spectral ◽  
Maximum Average Output Power ◽  
Ceramic Laser ◽  
Stable Passive

We report on a continuous-wave (CW) and passively Q-switched Er:Y2O3 ceramic laser in mid-infrared spectral region. In the CW regime, a maximum output power of 2.07 W is achieved at 2717.3 nm with a slope efficiency of 13.5%. Stable passive Q-switching of the Er:Y2O3 ceramic laser is demonstrated based on semiconductor saturable absorber mirror. Under an absorbed pump power of 12.4 W, a maximum average output power of 223 mW is generated with a pulse energy of 1.7 μJ and a pulse width of 350 ns at 2709.3 nm.

Sign in / Sign up

Export Citation Format

Share Document