scholarly journals Some Bio-Technical Properties of Flax Seeds, Fennel Seeds and Harmal Seed Capsules

2020 ◽  
pp. 222-232
Author(s):  
Gungor YILMAZ ◽  
Ebubekir ALTUNTAS
Keyword(s):  
Bulk Density ◽  
Static Friction ◽  
Angle Of Repose ◽  
True Density ◽  
Displacement Method ◽  
Rubber Friction ◽  
Length Width ◽  
Technical Properties ◽  
Flax Seeds ◽  
Liquid Displacement

Some bio-technical properties of flax seeds, fennel seeds, and harmal seed capsules were determined. The size dimensions (length, width, and thickness) of flax seeds and fennel seeds were as 4.31 mm, 2.28 mm, 0.87 mm; 6.93 mm, 2.13 mm, 1.75 mm, respectively. The diameter and length for harmal seed capsules were 9.07 mm and 6.65 mm, respectively. The true density (ρt) was determined using the liquid displacement method, and the bulk density (ρb) was determined using the hectolitre tester. The bulk density for flax seeds, fennel seeds, and harmal seed capsules were determined as 384.3 kg m-3, 270.5 kg m-3 and 201.5 kg m-3, while, true density was found as 1256.5 kg m-3, 664.6 kg m-3, 936.2 kg m-3 for flax seeds, fennel seeds, and harmal seed capsules, respectively. The sphericity of for flax seeds, fennel seeds and harmal seed capsules were obtained as 0.47, 0.43, 0.72, respectively. The angle of repose was obtained as 13.84º, 17.35º, 29.94º for flax seeds, fennel seeds, and harmal seed capsules, respectively. The rubber friction surface has given the highest static friction coefficient for flax seeds, fennel seeds, and harmal seed capsules.

RELATIONSHIP BETWEEN WEIGHT AND PHYSICO-MECHANICAL PROPERTIES OF COFFEE GRAINS PRODUCED FROM DIFFERENT HARVEST RIPENING

2014 ◽  
Vol 4 (1) ◽  
pp. 21-30
Author(s):  
Yuwana Yuwana ◽  
Evanila Silvia ◽  
Bosman Sidebang
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Static Friction ◽  
Linear Analysis ◽  
Angle Of Repose ◽  
True Density ◽  
Experiment Research ◽  
Positive Correlation ◽  
Length Width ◽  
Very High

This research aimed to determine relationships between weight and several physic-mechanical properties of coffee grains. Grains having 12.2% (wet basis) moisture content in average, originated from cherries of different ripening levels identified by green, yellow, red and deep red in colors were used for experiment. Research used regresi linear analysis. Results of experiment indicated that weight of grains positively correlated to length, width, thickness and frontal area with very high values of determination coefficient. Weight of grains correlated positively to sphericity and negatively to porosity. Weight of grains originated from green and red cherries had positive correlation with density whereas weight of grains originated from yellow and deep red cherries possessed no correlation with density. Weight of grains from yellow, red and deep red cherries had negative correlation with true density in contrast weight of grains from green cherries had positive correlation with true density. There were no reliable trend concerning the relationships between weight of grains and coefficient of static friction and angle of repose.

scholarly journals Determination of Selected Moisture -Dependent Physical and Frictional Properties of Shelled Egusi Melon (Citrullus lanatus Thunb.)

2017 ◽  
Vol 2 (1) ◽  
Author(s):  
Adesola A Satimehin ◽  
Terseer M Akaayar
Keyword(s):  
Internal Friction ◽  
Bulk Density ◽  
Citrullus Lanatus ◽  
Static Friction ◽  
Angle Of Repose ◽  
Test Material ◽  
True Density ◽  
Efficient Design ◽  
Frictional Properties ◽  
Melon Seeds

Physical and frictional properties were determined for shelled (i.e. hulled) seeds of egusi melon (Citrullus lanatus Thunb) at moisture content levels of 11.04, 15.7, 21.03 and 24.78 % dry basis. The physical properties investigated were true density, bulk density and the angle of repose; while the frictional properties were the coefficient of static friction and the coefficient of internal friction.  Densities were determined using the volume displacement method, while the bulk porosity was calculated as a function of the true and bulk densities. The angle of repose was measured using the cylinder method. The coefficient of static friction of melon seeds on the surfaces of plywood, galvanized iron and glass was determined by sliding a cell filled with the seeds on a tilting table overlaid with the test material surfaces. The coefficient and internal angle of friction were determined by means of a shear test apparatus. Within the range of moisture investigated, the true density of shelled melon seeds decreased from 1,264 to 1,239 kg/m3 while its bulk density increased from 668 to 681 kg/m3. The porosity decreased from 47.19 to 45.36 % while the angle of repose increased from 31.0 to 34.9°. The coefficient of friction of shelled melon seeds on the surfaces of glass, galvanised iron and plywood  increased from 0.329 to 0.475, 0.364 to 0.476 and 0.408 to 0.559 respectively. The coefficient and angle of internal friction increased from 0.638 to 0.668 and 32.52 to 33.74°, respectively. These findings are valuable data for efficient design of machines for processing, handling and storage of hulled seeds of egusi melon.

scholarly journals Physical Properties of Different Cultivar Local Glutinous rice (susu and siding) and Commercial Thai Cultivar

2021 ◽  
Author(s):  
Norzahirah Zainal ◽  
Rosnah Shamsudin
Keyword(s):  
Oryza Sativa ◽  
Aspect Ratio ◽  
Physical Properties ◽  
Bulk Density ◽  
Angle Of Repose ◽  
True Density ◽  
White Rice ◽  
Glutinous Rice ◽  
Length Width ◽  
Waxy Rice

Glutinous rice (Oryza Sativa var. glutinosa) is known as waxy rice or sticky rice and it has an opaque and small size grain cultivar distinct from common white rice. In outlining the equipment for processing, storage, sorting, sizing and other post-harvest equipment the particular of their physical properties is important. Two different cultivar of local glutinous rice susu and siding were evaluated in this study. For susu cultivar, the average of length, width, and thickness were 6.63mm, 1.88mm, and 1.50mm respectively. The corresponding values were 6.24mm, 1.98mm, and 1.48mm for siding cultivar. For susu cultivar, the average of aspect ratio, sphericity, volume, surface area, bulk density, true density, porosity, 1000 weight kernel, and angle of repose were 0.28, 0.40%, 9.81mm3, 19.02mm2, 800.54 kg/m3, 1500.36 kg/m3, 46.65%, 18.88g, and 39.45°. Thecorresponding values were 0.32, 0.42%, 10.25mm3, 19.45mm2, 772.73 kg/m3, 1229.51 kg/m3, 37.15%, 17.04g and 40.08° for siding cultivar. Thus, the objective of this study is to compare the physical properties of two different local cultivars aid in designing the rice processing equipment.

scholarly journals Comparison of the physical properties between Malaysian and Thai Rice

2021 ◽  
Author(s):  
Parichart Sathongpan ◽  
Rosnah Shamsudin ◽  
Jaturapatr Varith ◽  
Nur Farhana Abd Rahman
Keyword(s):  
Aspect Ratio ◽  
Physical Properties ◽  
Bulk Density ◽  
Surface Area ◽  
Angle Of Repose ◽  
Physical Parameters ◽  
True Density ◽  
Breadth Ratio ◽  
Length Width

Rice is a staple food in the world market, especially in the Asian region. In each country, the characteristics of rice will be different in terms of shape, grade and size. The quality of rice depends largely that demonstrate the quality of that rice species. At present, information on rice varieties is still limited regarding the physical properties of Malaysian and Thai rice. Therefore, it is important to compare rice cultivars based on origin. The objective of this research is to determine and compare the physical properties of Malaysian and Thai rice. 1 kilogram of Malaysian and Thai rice were each processed into powder by way of grinding and were then prepared for physicochemical measurement by sieving the produced rice powders with a size of 2mm to get rid of foreign objects. The physical parameters measured were length, width, length/breadth ratio, thickness, density, grain shape, surface area, bulk density, true density, porosity, sphericity, aspect ratio, thousand weight kernels angle of repose, colour (L, a*, b*) and hardness. The results of the study showed no significant differences (p>0.05) in terms of length, width, length/breadth ratio, true density, porosity, sphericity, aspect ratio, angle of repose, Lightness (L) and b*. However, there is a significant variation (p < 0.05) between Malaysian and Thai rice in terms of thickness, surface area, bulk density, thousand weight kernels, colour (a*) and hardness parameters. The evaluation of the quality of Malaysian and Thai rices can be a guide or reference for the grading and sorting processing sectors. 

Physical Properties of Finola® Hemp Seeds: Clean and Containing Dockages

2018 ◽  
Vol 34 (6) ◽  
pp. 1017-1026 ◽  
Author(s):  
Fuji Jian ◽  
Sam Yavari ◽  
Ramasamy Boopathy Narendran ◽  
Digvir S. Jayas
Keyword(s):  
Moisture Content ◽  
Physical Properties ◽  
Bulk Density ◽  
Galvanized Steel ◽  
Angle Of Repose ◽  
True Density ◽  
Average Surface ◽  
Moisture Contents ◽  
Length Width ◽  
Average Surface Area

Abstract.Physical properties of hemp seeds (, L., cultivar Finola®) with 5%, 10%, and 15% foreign materials and dockages (FMD) at 9%, 12%, and 15% moisture contents (wet basis) were measured. The measured and determined physical properties include physical dimensions (length, width, thickness, kernel volume, sphericity, and average surface area), density (bulk and true density), porosity, weight of 1000 kernels, filling and empting angles of repose, and coefficients of friction on surfaces of plywood, galvanized steel, steel-troweled concrete, and wood-floated concrete. The mean value of the length, width, and thickness of the 50 kernels had a linear relationship with the increase of moisture content; however, this was not true for individual kernels. Bulk density of seeds at any FMD level decreased linearly or quadratically with the moisture content increase, while the true density had an opposite trend. Increasing FMD significantly increased the bulk density at any moisture content, and there were variations for the true density. There were gaps between the seed coat and cotyledon, and these gaps became smaller or disappeared when the seed moisture content was increased. This phenomenon resulted in the same average surface area, same volume, and exponential increase in porosity to 58.5% with the increase of moisture content. Increased FMD significantly decreased the porosity at any moisture content. Emptying angle of repose increased with the increase of moisture contents and percentage of FMD. Higher variability was observed in the filling angle of repose than in the emptying angle of repose. The coefficient of friction was the largest against wood-floated and steel-troweled concrete, followed by galvanized steel, and the smallest was against the plywood surface. Keywords: Angle of repose, Density, Foreign material and dockage (FMD), Friction against structural surface, Hemp seed, Physical dimensions.

scholarly journals Comparative Studies on Dimensional, Gravimetric and Frictional Properties of Chhattisgarh Popular Paddy Varieties for Suitability of Flaked Rice (Paha)

2020 ◽  
pp. 145-151
Author(s):  
Rahul Dahare ◽  
Tankesh Kumar Nishad ◽  
Bhupendra Sahu
Keyword(s):  
Aspect Ratio ◽  
Bulk Density ◽  
Average Length ◽  
Geometric Mean ◽  
Angle Of Repose ◽  
True Density ◽  
Frictional Properties ◽  
Mean Diameter ◽  
Length Width ◽  
Different Characteristics

The present study on different characteristics of some selected varieties of paddy was undertaken to study dimensional, gravimetric and frictional properties of paddy. The physical properties such as average length, width, thickness, geometric mean diameter, aspect ratio, sphericity, volume, surface area, L/B ratio, true density, bulk density, porosity, angle of repose and coefficient of friction on different surfaces of paddy varieties were measured to have an initial information of the input. All varieties have different dimensional properties, for the length of Rajeshwari, Durgeshwari and Mahamaya paddy variety 9.21 to 9.34 mm, for width 2.41 to 2.79 mm and for thickness 1.83 to 2.45 mm respectively. The geometric mean diameter and aspect ratio for Rajeshwari, Durgeshwari and Mahamaya paddy variety was observed 3.43 to 4.08 mm and 25.21 to 30.13% respectively. True density and bulk density of Rajeshwari, Durgeshwari and Mahamaya paddy variety were observed 1056.86 to 1350.43 kg/m3 and 580.18 to 695.77 kg/m3 respectively. The angle of repose of Rajeshwari, Durgeshwari and Mahamaya paddy variety was observed 42.23° to 48.51°.

scholarly journals DETERMINATION OF PHYSICAL AND ENGINEERING PROPERTIES OF TIGER NUT (Cyperus esculentus) RELEVANT TO ITS MECHANIZATION

2020 ◽  
Vol 5 (8) ◽  
Author(s):  
Tega A Emurigho ◽  
Canice O.O Kabuo ◽  
Arinze N Ifegbo
Keyword(s):  
Moisture Content ◽  
Static Friction ◽  
Major Axis ◽  
Angle Of Repose ◽  
Engineering Properties ◽  
Cyperus Esculentus ◽  
Mean Values ◽  
Principal Axes ◽  
Length Width ◽  
The Mean

The physical and engineering properties of fresh and dried tiger nut (Cyperus esculentus) were determined at moisture content of 41.20% and 16.40% on wet basis respectively. The mean values for the three principal axes (length, width and thickness) were 9.52mm, 8.16mm, and 8.16mm for fresh tiger nut and 9.14mm, 7.72mm and 8.03mm for dried tiger nut respectively, showing a decrease with decrease in moisture content and was significantly different at p?0.05. The mean values of the bulk density, true density and porosity of both fresh and dried tiger nut were 0.59g/cm3 , 0.97g/cm3 , 40.61 and 0.58g/cm3, 0.94g/cm3 , 40.35 respectively and were not significantly different at p?0.05. The mean angle of repose and coefficient of static friction over formica, stainless steel, glass and plywood surfaces of fresh tiger nut were 50.11o , 2.73, 2.45, 2.22 and 1.77 while that of dried tiger nut were 48.23o , 2.41, 2.03, 2.11 and 2.00 respectively. The mean rupture force increased with compression force of 90.08N on the major axis to 116.88N for fresh tiger nut and from 120.55N to 161.10N for dried tiger nut and were significantly different at p?0.05. These properties determined are necessary in the design and fabrication of hoppers, conveyor equipment and the force tiger nut can withstand before it is ruptured.

scholarly journals Effect of Moisture Content on Selected Physical and Mechanical Properties of Two Varieties of Tigernut (Cyperus spp)

2013 ◽  
Vol 2 (6) ◽  
pp. 24
Author(s):  
A. S. Oyerinde ◽  
A. P. Olalusi
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Bulk Density ◽  
Average Length ◽  
Physical And Mechanical Properties ◽  
Static Friction ◽  
Angle Of Repose ◽  
Tuber Weight ◽  
Porosity Coefficient ◽  
Effect Of Moisture

<p>The effect of moisture content on some physical and mechanical properties of two varieties of tigernuts (<em>Cyperus esculentus</em>) was investigated. These properties include: geometric dimensions, linear dimensions, 1000 tuber weight, bulk density, tuber size, sphericity, angle of repose, porosity, coefficient of static friction and compressive strength. The moisture content levels used were 20, 25, 30, 35 and 40% wet basis (wb), and the two tigernut varieties used were yellow and brown types. The linear dimension, geometric diameter, sphericity, 1000- tuber weight, bulk density and angle of repose in both varieties increased with increasing moisture content. The average length, width and thickness of the yellow variety increases more than the brown variety at the determined moisture contents. True density of the yellow variety increased while the brown variety decreased with increase in moisture content. The porosity of the yellow variety reduces with increase in moisture content from 45.95 at 20% mc to 42.4 at 40% mc, while the brown variety decreased from 42.72 at 20% mc to 30.77 at 40% moisture content. The yellow variety had bigger size tubers than the brown variety and this has serious implications in packing, handling and transportation issues.</p>

scholarly journals Study on some engineering attributes of pine nut (Pinus pinea) to the design of processing equipment

2010 ◽  
Vol 56 (No. 3) ◽  
pp. 99-106 ◽  
Author(s):  
S.M.T. Gharibzahedi ◽  
V. Etemad ◽  
J. Mirarab-Razi ◽  
M. Fos hat
Keyword(s):  
Moisture Content ◽  
Geometric Mean ◽  
Seed Mass ◽  
Static Friction ◽  
Terminal Velocity ◽  
Angle Of Repose ◽  
Engineering Properties ◽  
Pine Nut ◽  
Length Width ◽  
Glass Surfaces

Moisture-dependent engineering properties of pine nut were studied at 6.3, 8.2, 10.8, 14.5, 18.9, and 20.1% moisture content (dry basis). The length, width, thickness, and geometric mean diameter increased significantly (P &lt; 0.05) from 21.75 to 21.85 mm, 7.39 to 7.47 mm, 6.07 to 6.14 mm, and 9.89 to 9.98 mm, respectively, with an increase in moisture content from 6.3% to 20.1%, whereas the increase in sphericity from 45.49% to 45.69% was not significant. Similarly, thousand seed mass, true density, porosity, terminal velocity, and angle of repose increased (P &lt; 0.05) from 0.85 to 0.93 kg, 1043.3 to 1071 kg/m3, 41.31% to 44.57%, 8.67 to 8.83 m/s, and 35.4&deg; to 39&deg;, respectively, with an increase in moisture content under the experimental condition. Moreover, the bulk density decreased significantly (P &lt; 0.05) from 612.3 to 593.6 kg/m3. Coefficient of static friction increased (P &lt; 0.05) from 0.251 to 0.292, 0.241 to 0.271, 0.227 to 0.262, and 0.218 to 0.247 on plywood, galvanized iron sheet, stainless steel, and glass surfaces, respectively, with an increase in moisture content from 6.3% to 20.1%.

scholarly journals Physical Attributes and Modelling of Trans- Himalayan Seabuckthorn Berries

2017 ◽  
Vol 5 (3) ◽  
pp. 391-397 ◽  
Author(s):  
SWAPNIL G. JAISWAL ◽  
BHUSHAN R. DOLE ◽  
SANGRAM K. SATPATHY ◽  
S.N. NAIK
Keyword(s):  
Bulk Density ◽  
Surface Area ◽  
Geometric Mean ◽  
Polynomial Model ◽  
Angle Of Repose ◽  
True Density ◽  
North Eastern ◽  
Mean Diameter ◽  
Physical Attributes ◽  
In Trans

Seabuckthorn is a highly perishable fruit found in trans-Himalayan region and North-Eastern part of India. It has enormous nutritional and medicinal properties. Physical attributes of fruits play an important role in the design of machines to meet various harvest and post harvest operations. In the present study properties like dimensions, true density, bulk density, sphericity, porosity and angle of repose were measured and correlated with the mass of the fruit. In addition linear, polynomial, quadratic, logarithmic and exponential models were used for mass and surface area. The length, diameter, thousand berry weight, geometric mean diameter, arithmetic mean diameter, surface area, aspect ratio, angle of repose, sphericity, porosity, true density, bulk density, moisture content were found in the range of 6.5-7.5, 4.74-6.28, 362.67-910.14, 5.49-6.99, 6.17-6.24, 76.87-154.76, 72.81-83.73, 3.59-6.82, 65.84-90.47, 17.05-60.07, 647.19-1399.24, 453.81-725.88, 84.53-87.34 respectively. Polynomial model was suited to be best for mass with length and diameter. Polynomial model between surface area and geometric mean diameter gave highest R2 of 0.981.

Sign in / Sign up

Export Citation Format

Share Document