scholarly journals Automation and Electronic Control of Marine Gas Turbine Engine for Ship Revamp

2020 ◽  
Vol 2 (4) ◽  
pp. 98-108
Author(s):  
Filip Niculescu ◽  
Claudia Borzea ◽  
Adrian Savescu ◽  
Andrei Mitru ◽  
Mirela Letitia Vasile
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
State Of The Art ◽  
Weight Ratio ◽  
Electronic System ◽  
Turbine Engines ◽  
Control Panel ◽  
Electronic Control ◽  
Turbine Engine ◽  
Operation Costs

Gas turbines used in propulsion ensure increased efficiency and safety, with a very good power / weight ratio and with low maintenance and operation costs. Due to becoming out-of-date and reaching the maximum operation hours and expected lifetime, which can cause malfunctioning, older turbine engines on frigates need to be replaced with newer generation propulsion engines. The paper presents the replacement of the turbine engine on a defence frigate, focusing on the automation and electronic control solution employed for a propulsion turbine, integrating state-of-the-art techniques. The electronic system ensures control, monitoring and alarm functions, including overspeed protection. A local control panel interfacing the PLC displays the operating parameters and engine controls, also providing maintenance and calibration sequences. The proposed solution enables both the local and the remote control of the ship’s gas turbine.

Design, Development and Application of Vehicle Gas Turbine Engines

1966 ◽  
Vol 181 (1) ◽  
pp. 149-172
Author(s):  
P. A. Phillips ◽  
Peter Spear
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Low Cost ◽  
Engine Performance ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Design Development ◽  
Turbine Engine ◽  
Wide Range ◽  
Cycle Temperature

After briefly summarizing worldwide automotive gas turbine activity, the paper analyses the power plant requirements of a wide range of vehicle applications in order to formulate the design criteria for acceptable vehicle gas turbines. Ample data are available on the thermodynamic merits of various gas turbine cycles; however, the low cost of its piston engine competitor tends to eliminate all but the simplest cycles from vehicle gas turbine considerations. In order to improve the part load fuel economy, some complexity is inevitable, but this is limited to the addition of a glass ceramic regenerator in the 150 b.h.p. engine which is described in some detail. The alternative further complications necessary to achieve satisfactory vehicle response at various power/weight ratios are examined. Further improvement in engine performance will come by increasing the maximum cycle temperature. This can be achieved at lower cost by the extension of the use of ceramics. The paper is intended to stimulate the design application of the gas turbine engine.

Inlet Fogging of Gas Turbine Engines: Part A — Theory, Psychrometrics and Fog Generation

2000 ◽  
Author(s):  
Cyrus B. Meher-Homji ◽  
Thomas R. Mee
Keyword(s):  
Gas Turbine ◽  
Air Temperature ◽  
Gas Turbines ◽  
State Of The Art ◽  
Ambient Air ◽  
Process Industry ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Strong Function ◽  
Turbine Output

Gas Turbine output is a strong function of the ambient air temperature with power output dropping by 0.3–0.5 % for every 1°F rise in ambient temperature. This loss in output presents a significant problem to utilities, cogenerators and IPPs when electric demands are high during the hot months. In the petrochemical and process industry, the reduction in output of mechanical drive gas turbines curtails plant output. One way to counter this drop in output is to cool the inlet air. The paper contrasts the traditional evaporative cooling technique with direct inlet fogging. The state of the art relating to fog generation and psychrometrics of inlet fogging are described.

Gas Turbine Power Systems for Military Tracked Vehicles

1983 ◽  
Author(s):  
Geoffrey D. Woodhouse
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Waste Heat ◽  
High Reliability ◽  
Turbine Engines ◽  
Tracked Vehicles ◽  
Turbine Engine ◽  
Response Characteristics ◽  
Air Inlet

The gas turbine engine has been examined as a power plant for military tracked vehicles for over 30 years. Advocates have stressed the potentially high power density and high reliability as factors in favor of the turbine. Several turbine engines have been evaluated experimentally in military tracked vehicles resulting in a better understanding of such aspects as response characteristics and air inlet filtration requirements. Moreover, although the small volume and light weight of aircraft derivative gas turbines have certain virtues, it generally has been concluded that some form of waste heat recuperation is essential to achieve an acceptable level of fuel consumption, despite the increased weight and volume incurred. The selection of the AVCO Lycoming AGT1500 recuperated gas turbine as the power unit for the U.S. Army new M1 “Abrams” main battle tank was a major milestone in the evolution of gas turbine engines for tank propulsion.

Low-Leakage Modular Regenerators for Gas-Turbine Engines

1997 ◽  
Author(s):  
James Anthony Kluka ◽  
David Gordon Wilson
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Regenerative Heat ◽  
Turbine Engine ◽  
Low Leakage ◽  
The Matrix ◽  
Potential Applications ◽  
Ceramic Honeycomb

One of the significant problems plaguing regenerator designs is seal leakage resulting in a reduction of thermal efficiency. This paper describes the preliminary design and analysis of a new regenerative heat-exchanger concept, called a modular regenerator, that promises to provide improved seal-leakage performance. The modular regenerator concept consists of a ceramic-honeycomb matrix discretized into rectangular blocks, called modules. Separating the matrix into modules substantially reduces the transverse sealing lengths and substantially increases the longitudinal sealing lengths as compared with typical rotary designs. Potential applications can range from small gas-turbine engines for automotive applications to large stationary gas turbines for industrial power generation. Descriptions of two types of modular regenerators are presented including sealing concepts. Results of seal leakage analysis for typical modular regenerators sized for a small gas-turbine engine (120 kW) predict leakage rates under one percent for most seal-clearance heights.

Analysis of Indirectly Fired Gas Turbine Power Systems

2007 ◽  
Author(s):  
J. E. Donald Gauthier
Keyword(s):  
Power Generation ◽  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Turbine Engine ◽  
Engine Design ◽  
Wide Range ◽  
System Configurations

This paper describes the results of modelling the performance of several indirectly fired gas turbine (IFGT) power generation system configurations based on four gas turbine class sizes, namely 5 kW, 50 kW, 5 MW and 100 MW. These class sizes were selected to cover a wide range of installations in residential, commercial, industrial and large utility power generation installations. Because the IFGT configurations modelled consist of a gas turbine engine, one or two recuperators and a furnace; for comparison purpose this study also included simulations of simple cycle and recuperated gas turbine engines. Part-load, synchronous-speed simulations were carried out with generic compressor and turbine maps scaled for each engine design point conditions. The turbine inlet temperature (TIT) was varied from the design specification to a practical value for a metallic high-temperature heat exchanger in an IFGT system. As expected, the results showed that the reduced TIT can have dramatic impact on the power output and thermal efficiency when compared to that in conventional gas turbines. However, the simulations also indicated that several configurations can lead to higher performance, even with the reduced TIT. Although the focus of the study is on evaluation of thermodynamic performance, the implications of varying configurations on cost and durability are also discussed.

Technological Trend of Aircraft Gas Turbines and its Effect on the Development for Ship Propulsion Plants

1970 ◽  
Author(s):  
N. K. H. Scholz
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Gas Turbine Engine ◽  
Design Parameters ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Compression Pressure ◽  
Turbine Engine ◽  
Ship Propulsion

The effect of the main design parameters of the aero gas turbine engine cycle, namely combustion temperature and compression pressure ratio, on the specific performance values is discussed. The resulting development trend has been of essential influence on the technology. Relevant approaches are outlined. The efforts relating to weight and manufacturing expense are also indicated. In the design of aero gas turbine engines increasing consideration is given to the specific flight mission requirements, such as for instance by the introduction of the by-pass principle. Therefore direct application of aero gas turbine engines for ship propulsion without considerable modifications, as has been practiced in the past, is not considered very promising for the future. Nevertheless, there are possibilities to take advantage of aero gas turbine engine developments for ship propulsion systems. Appropriate approaches are discussed. With the experience obtained from aero gas turbine engines that will enter service in the early seventies it should be possible to develop marine gas turbine engines achieving consumptions and lifes that are competitive with those of advanced diesel units.

Gas Turbines For Helicopters

1958 ◽  
Vol 62 (573) ◽  
pp. 646-654 ◽  
Author(s):  
A. W. Morley
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Liquid Fuel ◽  
Korean War ◽  
Turbine Engines ◽  
Gradual Improvement ◽  
Turbine Engine ◽  
Civil Aircraft ◽  
The Korean War ◽  
Made In

Rapid developments in the use of the helicopter were made in the Korean War. These were taking place at the time when there was considerable urge to introduce the gas turbine engine into the civil aircraft market. It was also a time when much effort was being expended on various forms of reaction propulsion, mostly for missiles. A number of new helicopter projects were started, taking advantage of the new knowledge in propulsion engineering; some utilised new gas turbine designs and others various forms of tip jet reaction. Liquid fuel rockets, ram-jets, pulse-jets and air pressure jets were tried. However, the main line of development continued to be the gradual improvement of direct mechanical drive.Since Korea the natural trend has been first to convert existing helicopters to turbine engines. When new helicopters were designed wisdom dictated mechanical drive pending the gathering of sufficient experience with other forms of rotor power, and so far the accumulated knowledge of the mechanical drive has proved of greater value to helicopter progress than the potential advantages offered by the alternative engine forms.

scholarly journals Thermomechanical Advances for Small Gas Turbine Engines: Present Capabilities and Future Direction in Gas Generator Designs

1988 ◽  
Author(s):  
M. Propen ◽  
H. Vogel ◽  
S. Aksoy
Keyword(s):  
Gas Turbine ◽  
Broad Spectrum ◽  
Gas Turbines ◽  
Weight Ratio ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Gas Generator ◽  
Performance Requirements ◽  
Materials Research ◽  
Future Direction

Performance requirements of tomorrow’s gas turbines demand major improvements in specific fuel consumption and thrust to weight ratio. These stringent requirements, in turn, drive the need for higher operating temperatures and lighter weight engines. Such technical improvements impose severe thermal, structural, and metallurgical demands upon turbine components. A broad spectrum of technology programs is underway at Textron Lycoming to address these challenging requirements. This paper outlines the thermal, structural, and materials research needed for achieving the goals of the small gas turbines of tomorrow.

scholarly journals Development of Gas Turbines for Road Vehicles

1957 ◽  
Author(s):  
A. Carelli
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Engine Performance ◽  
Road Transport ◽  
Gas Turbine Engine ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Engine ◽  
Operational Characteristics ◽  
Design Construction

The experience acquired in developing an automotive gas-turbine engine is traced. Problems of design, construction, and development unique to a small gas-turbine engine and its application to an automobile are discussed. The engine performance and operational characteristics are then described. Finally, there is a discussion of the problems that must be solved before gas-turbine engines may successfully compete with reciprocating engines in automotive road transport.

Low-Leakage Modular Regenerators for Gas-Turbine Engines

1998 ◽  
Vol 120 (2) ◽  
pp. 358-362 ◽  
Author(s):  
J. A. Kluka ◽  
D. G. Wilson
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Regenerative Heat ◽  
Turbine Engine ◽  
Low Leakage ◽  
The Matrix ◽  
Potential Applications ◽  
Ceramic Honeycomb

One of the significant problems plaguing regenerator designs is seal leakage resulting in a reduction of thermal efficiency. This paper describes the preliminary design and analysis of a new regenerative heat-exchanger concept, called a modular regenerator, that promises to provide improved seal-leakage performance. The modular regenerator concept consists of a ceramic-honeycomb matrix discretized into rectangular blocks, called modules. Separating the matrix into modules substantially reduces the transverse sealing lengths and substantially increases the longitudinal sealing lengths as compared with typical rotary designs. Potential applications can range from small gas-turbine engines for automotive applications to large stationary gas turbines for industrial power generation. Descriptions of two types of modular regenerators are presented including sealing concepts. Results of seal leakage analysis for typical modular regenerators sized for a small gas-turbine engine (120 kW) predict leakage rates under one percent for most seal-clearance heights.

Sign in / Sign up

Export Citation Format

Share Document