scholarly journals BETON BERMUTU DAN RAMAH LINGKUNGAN DENGAN MEMANFAATKAN LIMBAH ABU BAN BEKAS

2021 ◽  
Vol 2 (2) ◽  
pp. 141-149
Author(s):  
Johan Oberlyn Simanjuntak ◽  
Tiurma Elita Saragi ◽  
Ros Anita Sidabutar ◽  
Humisar Pasaribu ◽  
Rido Parulian Simbolon

The need for housing is increasing day by day. This is a factor in the visit to the need for concrete as a housing construction material. The more concrete that is produced, the more cement is needed for the construction. Concrete is a composite material (mixture) of several materials, the main ingredient of which consists of a mixture of cement, fine aggregate, coarse aggregate and water. Utilization of waste tire ash in the concrete mix is one of the alternative uses so that ic can ultimately increase the efficiency of cement savings which takes a long time to increase in high prices. With reference to this, this study uses used waste as a cement additive with a mixture composition of 0%, 3%, 6% and 9%. The test specimens were made using a cylinder with a diameter of 15 cm and a height of 40 cm with 48 specimens produced. The results of the compressive strength test of normal concrete (25.45 MPa), while the concrete with a mixture of 3% used tire ash (28.15 MPa), 6% used tire ash mixture (23.46 MPa) and 9% used tire ash mixture (18.60 MPa). From this research, it can be said that compressive strength of concrete using 3% ash produces the greatest compressive strength of 28.15 MPa.

2020 ◽  
Vol 1 (1) ◽  
pp. 79-98
Author(s):  
Johan Oberlyn Simanjuntak ◽  
Tiurma Elita Saragi ◽  
Belinauli Teknika Lumban Gaol

The need for housing is more higher along with the times and this is also a factor to increasing for concrete needed for building  development. The more concrete that is produced, the more cement is needed for construction.Concrete is a composite material (mixture) of several materials, the main ingredient which consists of a mixture of cement, fine aggregate, coarse aggregate, water and or without other additives with a certain ratio. Utilization of waste carried out in this study is to utilize corn cobs waste which is commonly found in the outskirts of the city of Medan. By utilizing this waste, it is hoped that it can reduce the accumulation of corn agricultural waste and also increase public insight about how to treat corn cobs waste into other forms. In this study, a concrete trial was carried out by adding corn cobs ash waste to concrete which aims to find out whether corn cobs ash can increase the compressive strength of concrete with variations in the percentage of the mixture of 0%, 3%, 6%, and 9% of the cement weight. The compressive strength value of normal concrete (25.45MPa), while with the substitution of corn cob ash 3% (21.96 MPa), 6% (18.56MPa), and 9% (16.45MPa). So it can be concluded that the resulting compressive strength exceeds the planned compressive strength and the optimum substitution value of corn cobs varian is at the 3% variant, namely 21.96 MPa.


2021 ◽  
Vol 3 (4) ◽  
pp. 132-140
Author(s):  
Mulyati Mulyati ◽  
Wiki Yulandi

This research uses paper ash, lokan shell powder, and sikacim concrete additivefor normal concrete mix. Paper ash is used as a cement additive, while lokan shell powder is used as a partial substitute for sand. To overcome the lack of water in the concrete mixture, Sikacim concrete additive is used. The purpose of this study was to determine the compressive strength of concrete resulting from the use of paper ash as an additive and lokan shell powder as a substitute for sand by adding sikacim concrete additive.The test object used a cube mold of 15 cm x 15 cm x 15 cm with a concrete compressive strength of K-250 design at the age of 28 days of testing. Variations of the specimens used paper ash 0.25% by weight of cement, and lokan shell powder 0%, 10%, 20%, 30% by weight of sand, and 0.7% additive from the volume of water. Based on the results of the compressive strength test of concrete, the compressive strength of concrete is obtained, for normal concrete it is 276.6 kg/cm2, from the use of 0.25% paper ash, 0% lokan shell and 0.7% additive of 362.6 kg/cm2, from the use of 0.25% paper ash, 10% lokan shell and 0.7% additive of 365.3 kg/cm2, from the use of 0.25% paper ash, 20% lokan shell and 0.7% additive of 300.53 kg /cm2, from the use of 0.25% paper ash, 30% lokan shell and 0.7% additive of 250.16 kg/cm2.


2021 ◽  
Vol 2 (2) ◽  
pp. 239-254
Author(s):  
Johan Oberlyn Simanjuntak ◽  
Ros Anita Sidabutar ◽  
Humisar Pasaribu ◽  
Yetty Riris R Saragi ◽  
Sriyanti Sitorus

Concrete is a construction material consisting of a mixture of cement, aggregate, water and with or without admixture if needed. Coarse aggregate and fine aggregate serve as the main filler of concrete as well as reinforcement, while the cement and water mixtured serves as a binder between materials. To find out and study the behavior of each of these concrete constituents, it is necessary to know the characteristics of the materials made as constituents of the concrete. This study was conducted with the aim of comparing the most optimum type of coarse aggregate used and the comparison of the use of cement for coarse aggregate of crushed stone and coarse aggregate of gully originating from North Sumatera area, namely from the Wampu River in Binjai City as a concrete mixture to see its effect on compressive strength of concrete at the same concrete characteristics namely f’c 25 MPa. The results of the normal concrete mix design are obtained by using coarse aggregate of crushed stone and coarse aggregate of boulder in different amounts of cement. The coarse aggregate of crushed stone requires more cement with the amount of cement 411.1 kg/m3 than the coarse aggregate of gum with the amount of cement 388.9 kg/cm3.


2020 ◽  
Vol 5 (2) ◽  
pp. 59-71
Author(s):  
Sri Devi Nilawardani

Title: The Effect of Using Mediteran Soil as Cement Substitution Materials in Compressive Strength and Tensile Strength of Concrete Concrete is a composite material (mixture) of cement, fine aggregate, coarse aggregate, and water. The potential of limestone in Indonesia is very large, reaching 28.678 billion tons which is the main ingredient in the cement manufacture. In the long run it will be depleted because it is a non-renewable natural resources. So to reduce the use of limestone the utilization of Mediteran soil as a substitution for some cement in the manufacture of concrete is required. The initial idea is based on the chemical composition contained in the Mediteran soil almost identical to the cement, which is carbonate (CaO) and silica (SiO2). The purpose of this research is to reveal the influence of substitution of Mediteran soil by 20% and 40% in the compressive strength and tensile of the concrete at age 3, 7, 14, and 28 days with the number of test specimen each 3 pieces on each variation in 10cm x20cm cylinder with planning of concrete mixture refers to SK SNI method T-15-1900-03. The type of research used is quantitative with the experimental method of laboratory test and data analysis of comparative method and regression. The results show that compressive strength and tensile strength of concrete using Mediteran soil substitution comparable to  the strength of normal concrete with dry treatment. In the composition of 20% Mediteran soils decreased by 51.35% or 7.9 MPa (compressive strength) and 30.60% or 0.93 MPa (tensile strength). While the composition of 40% Mediteran soil decreased by 43.78% or 9.13 MPa (compressive strength) and 2.24% or 1.31 MPa (tensile strength).  


Jurnal CIVILA ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 213
Author(s):  
Asrul Majid ◽  
Hammam Rofiqi Agustapraja

Infrastructure development is one of the important aspects of the progress of a country where most of the constituents of infrastructure are concrete. The most important constituent of concrete is cement because its function is to bind other concrete materials so that it can form a hard mass. The large number of developments using cement as a building material will leave quite a lot of cement bags.In this study, the authors conducted research on the effect of adding cement waste to the compressive strength of concrete. This study used an experimental method with a total of 24 test objects. The test object is in the form of a concrete cylinder with a diameter of 15 cm and a height of 30 cm and uses variations in the composition of the addition of cement waste cement as a substitute for fine aggregate, namely 0%, 2%, 4% and 6%. K200). The compressive strength test was carried out at the age of 7 days and 28 days.The test results show that the use of waste as a partial substitute for fine aggregate results in a decrease in the compressive strength of each mixture. at the age of 7 days the variation of 2% is 16.84 MPa, 4% is 11.32 MPa and for a mixture of 6% is 6.68 MPa. Meanwhile, the compressive strength test value of 28 days old concrete in each mixture decreased by ± 6 MPa. So the conclusion is cement cement waste cannot be used as a substitute for fine aggregate in fc 16.6 (K200) quality concrete because the value is lower than the specified minimum of 16.6 MPa.


2021 ◽  
Vol 328 ◽  
pp. 10006
Author(s):  
Daud Andang Pasalli ◽  
Dina Limbong Pamuttu ◽  
Rahmat Fajar Septiono ◽  
Chitra Utary ◽  
Hairulla Hairulla

The use of lightweight concrete materials in Indonesia, especially in the Merauke Regency area can be an alternative amid the rapid development of the housing sector. In this experimental study, the author took the initiative to replace coarse aggregate with wood charcoal as light coarse aggregate. The purpose of this study was to determine the value of compressive strength and to determine whether the wood charcoal material met the standard of lightweight concrete coarse aggregate. Planning the proportion of lightweight concrete mixture in this study using a volume ratio between cement, sand and wood charcoal of 1: 2, 1: 2: 2.5 and 1: 2: 5 with variations of test days at 3, 7, 14, 21 and 28 day. From the results of the compressive strength test of lightweight concrete, the use of wood charcoal aggregate as coarse aggregate in concrete causes the value of the compressive strength of concrete to decrease.


2021 ◽  
Vol 1 (1) ◽  
pp. 1
Author(s):  
Agung Prayogi

Abstract Concrete is the most widely used material throughout the world and innovations continue to be carried out to produce efficient development. Shell charcoal ash and rice husk ash are industrial by-products which have the potential to replace sand for concrete mix, especially in Indragiri Hilir. The research with the title "Effect of Mixture of Rice Husk Ash and Shell Ash Ashes as Substitute for Some Fine Aggregates Against Concrete Compressive Strength" aims to prove the effect of a mixture of shell charcoal ash and husk ash to replace some of the sand to produce maximum compressive strength. Concrete is a mixture of Portland cement, fine aggregate, coarse aggregate, and water. This research uses 5 variations of the mixture to the weight of sand, BSA 0 without a substitute mixture, BSA 1 with a mixture of 5% husk ash and 10% shell charcoal, BSA 2 with a mixture of 5% husk ash and 15% charcoal ash, BSA 3 with a mixture of 5% husk ash and 18% charcoal, BSA 4 with a mixture of 10% husk and 10% charcoal, and BSA 5 with a mixture of 13% husk ash and 10% charcoal ash. SNI method is used for the Job Mix Formula (JMF) mixture in this research. The results of the average compressive strength of concrete at 28 days for JMF of 21.05 MPa, BSA 1 of 23.68 MPa, BSA 2 of 22.23 MPa, BSA 3 of 14.39 MPa, BSA 4 of 13.34 MPa , and BSA 5 of 20.14 MPa. The conclusion drawn from the results of the BSA 1 research with a mixture of 5% husk ash and 15% charcoal ash produced the highest average compressive strength of 23.68 MPa. Abstrak Beton merupakan material paling banyak digunakan diseluruh dunia dan terus dilakukan inovasi untuk menghasilkan pembangunan yang efisien. Abu arang tempurung dan abu sekam padi merupakan hasil sampingan industri yang berpotensi sebagai pengganti pasir untuk campuran beton, khususnya di Indragiri Hilir. Penelitian dengan judul “Pengaruh Campuran Abu Sekam Padi dan Abu Arang Tempurung Sebagai Pengganti Sebagian Agregat Halus Terhadap Kuat Tekan Beton” ini bertujuan membuktikan adanya pengaruh campuran abu arang tempurung dan abu sekam untuk mengganti sebagian pasir hingga menghasilkan kuat tekan maksimum. Beton adalah campuran antara semen portland, agregat halus, agregat kasar, dan air. Penelitian ini menggunakan 5 variasi campuran terhadap berat pasir, BSA 0 tanpa campuran pengganti, BSA 1 dengan campuran 5 % abu sekam dan 10% arang tempurung, BSA 2 dengan campuran 5% abu sekam dan 15% abu arang, BSA 3 dengan campuran 5% abu sekam dan 18% arang, BSA 4 dengan campuran 10% sekam dan 10% arang, dan BSA 5 dengan campuran 13% abu sekam dan 10% abu arang. Metode SNI digunakan untuk campuran Job Mix Formula (JMF)  pada penelitian ini. Hasil rata-rata kuat tekan beton pada umur 28 hari untuk JMF sebesar 21,05 MPa, BSA 1 sebesar 23,68 MPa, BSA 2 sebesar 22,23 MPa, BSA 3 sebesar 14,39 MPa, BSA 4 sebesar 13,34 MPa, dan BSA 5 Sebesar 20,14 MPa. Ditarik kesimpulan dari hasil penelitian BSA 1 dengan campuran 5% abu sekam dan 15% abu arang menghasilkan rata-rata kuat tekan tertinggi yaitu sebesar 23,68 MPa.  


Aggregates used in concrete are fast depleting natural resource and the quarrying of which is causing environmental issues. Hence, the use of aggregate from alternate sources such as from waste discarded glass, from foundry sand discarded after metal casting process and sea shells is investigated. Compressive strength of concrete with glass powder, foundry sand and sea shell is studied individually. Concrete is cast with glass powder and foundry sand as 5%, 10%, 15% and 20% replacement of fine aggregate and with sea shell as 5%, 10%, 15% and 20% replacement of coarse aggregate individually. It is observed that compressive strength of concrete decreases with glass powder, foundry sand, and sea shell. Fine aggregate replaced by 10% glass powder, 10%, foundry sand and coarse aggregate replaced by 10% sea shell have the least decrease in strength when compared to control concrete mix.


Author(s):  
B Anitha Rani V Bhargavi,

Concrete is the most widely used construction material all over the world. The quantity of the water plays an important role in the preparation of concrete. And the demand of concrete is increasing day by day and cement is used for satisfying the need of development of infrastructure facilities, 1 tonne cement production generates 1 tonne CO2, which adversely affect the environment. In order to reduce the use of OPC and CO2 generation, the new generation concrete has been developed such as Geopolymer concrete (GPC). Geopolymers are inorganic polymers and their chemical composition is similar to natural materials. Geopolymer binders are the alternatives in the development of acid resistant concrete i.e. durability of concrete. Geopolymer concrete is produced using Fly ash at 100% replacement to cement and binders like NaOH, Na2SiO3 to ignite the geopolymerisation. Many studies were carried out on properties of geopolymer concrete. This study focuses on enhancing the strength of geopolymer concrete by using fibers. 60% polyester and 40% polypropylene fibers are added to geopolymer concrete addition with Fly ash content. The trail mixes were casted with addition of fibers at different percentages like (0.20, 0.25, 0.30, 0.35, 0.40, 0.45 and 0.50 %). Then samples were air-cured for 28 days at ambient temperature. Compressive strength test is conducted on the samples after 3, 7 and 28 days. The optimum value is obtained at 0.40% addition of fibers when compared to nominal mix(GPC).


Author(s):  
Nuttawut Intaboot ◽  
Kriangkrai Chartboot

This paper aimed to assess the potential of using limestone dust to replace sand at levels of 0, 20, 40, 60, 80 and 100% by weight. Concrete mix design for cement : fine aggregate : coarse aggregate was 1: 2 : 4 and 0.40, 0.50, 0.60 water-to-cement ratios were used. The study started by testing the basic properties of the material. The compressive strength test was done with curing for 7, 14, 21 and 28 days and modulus of elasticity of concrete at 28 days, after which the microstructural properties of concrete modified with limestone dust were investigated. The study found that the concrete had better workability when increasing the limestone dust content. The incorporation of 40% limestone dust at 0.50 water-to-cement ratios was found to improve the compressive strength of the concrete and resulted in the maximum compressive strength. However, high levels of replacement lead to porous microstructures. Moreover, the use of limestone dust in concrete production tends to be more cost-effective. Therefore, the results of this research seemingly provide confirmation and support for the utilization of these waste materials by reducing the use of natural resources. Further, it is a goal of local governments to help promote the value of limestone dust for future use.


Sign in / Sign up

Export Citation Format

Share Document