scholarly journals Strength Properties of Concrete with Aggregates from Alternate Sources

Aggregates used in concrete are fast depleting natural resource and the quarrying of which is causing environmental issues. Hence, the use of aggregate from alternate sources such as from waste discarded glass, from foundry sand discarded after metal casting process and sea shells is investigated. Compressive strength of concrete with glass powder, foundry sand and sea shell is studied individually. Concrete is cast with glass powder and foundry sand as 5%, 10%, 15% and 20% replacement of fine aggregate and with sea shell as 5%, 10%, 15% and 20% replacement of coarse aggregate individually. It is observed that compressive strength of concrete decreases with glass powder, foundry sand, and sea shell. Fine aggregate replaced by 10% glass powder, 10%, foundry sand and coarse aggregate replaced by 10% sea shell have the least decrease in strength when compared to control concrete mix.

2021 ◽  
Vol 1 (1) ◽  
pp. 1
Author(s):  
Agung Prayogi

Abstract Concrete is the most widely used material throughout the world and innovations continue to be carried out to produce efficient development. Shell charcoal ash and rice husk ash are industrial by-products which have the potential to replace sand for concrete mix, especially in Indragiri Hilir. The research with the title "Effect of Mixture of Rice Husk Ash and Shell Ash Ashes as Substitute for Some Fine Aggregates Against Concrete Compressive Strength" aims to prove the effect of a mixture of shell charcoal ash and husk ash to replace some of the sand to produce maximum compressive strength. Concrete is a mixture of Portland cement, fine aggregate, coarse aggregate, and water. This research uses 5 variations of the mixture to the weight of sand, BSA 0 without a substitute mixture, BSA 1 with a mixture of 5% husk ash and 10% shell charcoal, BSA 2 with a mixture of 5% husk ash and 15% charcoal ash, BSA 3 with a mixture of 5% husk ash and 18% charcoal, BSA 4 with a mixture of 10% husk and 10% charcoal, and BSA 5 with a mixture of 13% husk ash and 10% charcoal ash. SNI method is used for the Job Mix Formula (JMF) mixture in this research. The results of the average compressive strength of concrete at 28 days for JMF of 21.05 MPa, BSA 1 of 23.68 MPa, BSA 2 of 22.23 MPa, BSA 3 of 14.39 MPa, BSA 4 of 13.34 MPa , and BSA 5 of 20.14 MPa. The conclusion drawn from the results of the BSA 1 research with a mixture of 5% husk ash and 15% charcoal ash produced the highest average compressive strength of 23.68 MPa. Abstrak Beton merupakan material paling banyak digunakan diseluruh dunia dan terus dilakukan inovasi untuk menghasilkan pembangunan yang efisien. Abu arang tempurung dan abu sekam padi merupakan hasil sampingan industri yang berpotensi sebagai pengganti pasir untuk campuran beton, khususnya di Indragiri Hilir. Penelitian dengan judul “Pengaruh Campuran Abu Sekam Padi dan Abu Arang Tempurung Sebagai Pengganti Sebagian Agregat Halus Terhadap Kuat Tekan Beton” ini bertujuan membuktikan adanya pengaruh campuran abu arang tempurung dan abu sekam untuk mengganti sebagian pasir hingga menghasilkan kuat tekan maksimum. Beton adalah campuran antara semen portland, agregat halus, agregat kasar, dan air. Penelitian ini menggunakan 5 variasi campuran terhadap berat pasir, BSA 0 tanpa campuran pengganti, BSA 1 dengan campuran 5 % abu sekam dan 10% arang tempurung, BSA 2 dengan campuran 5% abu sekam dan 15% abu arang, BSA 3 dengan campuran 5% abu sekam dan 18% arang, BSA 4 dengan campuran 10% sekam dan 10% arang, dan BSA 5 dengan campuran 13% abu sekam dan 10% abu arang. Metode SNI digunakan untuk campuran Job Mix Formula (JMF)  pada penelitian ini. Hasil rata-rata kuat tekan beton pada umur 28 hari untuk JMF sebesar 21,05 MPa, BSA 1 sebesar 23,68 MPa, BSA 2 sebesar 22,23 MPa, BSA 3 sebesar 14,39 MPa, BSA 4 sebesar 13,34 MPa, dan BSA 5 Sebesar 20,14 MPa. Ditarik kesimpulan dari hasil penelitian BSA 1 dengan campuran 5% abu sekam dan 15% abu arang menghasilkan rata-rata kuat tekan tertinggi yaitu sebesar 23,68 MPa.  


2014 ◽  
Vol 665 ◽  
pp. 147-150 ◽  
Author(s):  
Ping Hua Zhu ◽  
Yi Lei

The strength properties of recycled aggregate concrete (RAC) using aggregates from repeatedly recycling concrete waste were studied. The relationships between cube compressive strength and splitting tensile strength and between each strength and replacement ratio of recycled aggregate to natural aggregate were established. The results showed that the strength properties of RAC with the design strength of 30MPa can be satisfied when the quality of recycled coarse and fine aggregates met respectively the needs of Grade II in GB/T25177-2010 and Grade III in GB/T25176-2010, with the replacement ratio to natural coarse aggregate and natural fine aggregate no more than 70% and 50%. Both strengths decreased and then increased for a while before descending again with increasing replacement ratio of recycled coarse aggregate, and decreased continuously with the increase of replacement ratio of recycled fine aggregate. The relationship between cube compressive strength and splitting tensile strength of RAC was found to be exponential function.


2021 ◽  
Vol 11 (4) ◽  
pp. 1952
Author(s):  
Euibae Lee ◽  
Jeongwon Ko ◽  
Jaekang Yoo ◽  
Sangjun Park ◽  
Jeongsoo Nam

In this study, the compressive strengths of concrete were investigated based on water content and aggregate volume fractions, comprising dune sand (DS), crushed sand (CS), and coarse aggregate (CA), for different ages. Experimental data were used to analyze the effects of the volume fraction changes of aggregates on the compressive strength. The compressive strength of concrete increases until the volumetric DS to fine aggregate (FA) ratio (DS/FA ratio) reaches 20%, after which it decreases. The relationship between changes in compressive strength and aggregate volume fractions was analyzed considering the effect factor of each aggregate on the compressive strength and at 2 conditions: (1) 0 < DS < CS < CA and (2) 0 < CA < CS < DS. For condition (1), when the effect factor of CA = 1, those of DS and CS were within 0.04–0.83 and 0.72–0.92, respectively, for all mixtures. For condition (2), when the effect factor of DS = 1, those of CS and CA were within 0.68–0.80 and 0.02–0.79, respectively.


2021 ◽  
Vol 2 (1) ◽  
pp. 46-54
Author(s):  
Neti Rahmawati ◽  
Irwan Lakawa ◽  
Sulaiman Sulaiman

Concrete is one of the most widely used building materials today interms of physical construction. Concrete is made from a mixture offine, coarse aggregate, cement, and water with a certain ratio, aswell as materials that are usually added to the concrete mixtureduring or during mixing, to changing the properties of concrete tomake it more suitable in certain jobs and more economical, can alsobe added with certain other mixed materials as needed if deemednecessary. Seashells can be used to mix concrete. This study aims todetermine whether the addition of shells aggregate shells in aconcrete mixture can affect the mechanical properties of concrete.The specimens used are in the form of cubes with a size of 15cm x 15cm x 15 cm, consisting of additional concrete coarse and fineaggregate with shell substitution percentage of 0%, 15%, 20% with atotal sample of 45, with the planned concrete quality of K225. Theuse of sea shells in increasing the compressive strength of concrete isbetter used as fine aggregate than coarse aggregate. The use of seashells as a substitute for fine aggregates achieves maximum resultsat 20% composition.


This paper presents an application of fuzzy logic to forecast the compressive strength of concrete. The fuzzy model examines 7 different input parameters that comprises: Cement, Coarse aggregate(CA), Super plasticizer(SP), Fine Aggregate(FA), Slag, Fly ash, Water(W), and 28 days compressive strength is taken as the output parameter. By using Gaussian membership function, the fuzzy logic technique is used for developing models. For assessing the results of FL model with experimental results, root mean square error, mean absolute error and correlation coefficient are used. The results showed that FL can be a better modeling tool and an another technique for predicting the concrete’s compressive strength.


2018 ◽  
Vol 7 (3.12) ◽  
pp. 831
Author(s):  
Suresh G ◽  
Harishankar S

The ceramic waste is used as a coarse aggregate replacement in concrete is a two way beneficial process that involves minimization of resources for construction and processing of hazardous industrial wastes that cannot be recycled. The ceramic waste obtained from waste dismantled building were used as coarse aggregate 10%, 20%, 30%, 40% and 50% replacement.  To improve the mechanical properties silica fume is added as admixture in the concrete. The optimum percentage replacement was obtained considering the strength as well as the objective of using ceramic waste aggregate. The compressive strength of concrete cubes were tested . The compressive strength of aggregate replaced concrete has been compared to that of conventional concrete and the results are evaluated. 


2020 ◽  
Vol 27 (3) ◽  
pp. 45-60
Author(s):  
Muataz Nayel ◽  
Ammar Khazaal ◽  
Waleed Alabdraba

Recently, the constructions industry begins to make concrete more sustainable, side by side, with making its high performance. This paper aims to investigate the effect of (Metakaolin and Micro Silica) when they replace cement by (8, 12 and 16) % and (6, 9 and 12) % respectively, recycled steel slag when replaces fine aggregate by (10, 20 and 30) %, and recycled mosaic tiles when replaces coarse aggregate by (33.33, 66.67 and 100) % each one another on the slump, density, absorption and compressive strength of concrete. The experimental results showed that the maximum reduction ratio of cement reach (17%) (8% of metakaolin and 9% Micro Silica) while the optimum percentage of mosaic tiles and steel slag is (100%) and (20%) respectively. The optimum percentages obtained are combining to produce three basic green mixes: 1) 17% (8% of Metakaolin and 9% of Micro Silica) only, (2) A mix containing 17% of (Metakaolin and of Micro Silica) plus 100% of recycled mosaic, (3) 17% of (Metakaolin and Micro Silica), 100% of recycled mosaic and 20% of slag. Compressive strength at (7, 28, and 60) days, modulus of rupture at (28) days, absorption, fresh and hardened density are investigated. The best improvement in compressive strength compared with reference concrete was recorded (20.06, 10.855 and 9.983) % at (7, 28 and 60) days respectively for the mix containing (17% of cementitious materials plus 100% of recycled mosaic) while the ultimate flexure strength (24) % appeared in green mix containing (17% of cementitious materials, 100% of recycled mosaic and 20% of slag). Generally, an inverse relationship between density and absorption in all trail mixes which are conducted


2013 ◽  
Vol 421 ◽  
pp. 390-394 ◽  
Author(s):  
Abdullah Mohd Mustafa Al Bakri ◽  
M.N. Norazian ◽  
M. Mohamed ◽  
H. Kamarudin ◽  
C.M. Ruzaidi ◽  
...  

This research focuses on a study of the strength of concrete with ceramic waste as coarse aggregate and quarry dust as fine aggregate. The sources of ceramic waste and quarry dust are obtained from the industrial in Malaysia. Presently, in ceramics industries the production goes as waste, which is not under going the recycle process yet. In this study an attempt has been made to find the suitability of the ceramic industrial wastes and quarry dust as a possible replacement for conventional crushed stone coarse and fine aggregate. Experiment were carried out to determine the strength of concrete with ceramic waste coarse aggregate and quarry dust fine aggregate to compare them with the conventional concrete made (with crushed stone coarse aggregate). From the results show that compressive strength of concrete with quarry dust as aggregates is the highest with 30.82 MPa with density 2251.85 kg/m3. This show, ceramic waste and quarry dust can be alternative aggregate for comparable properties.


2020 ◽  
Vol 1 (1) ◽  
pp. 79-98
Author(s):  
Johan Oberlyn Simanjuntak ◽  
Tiurma Elita Saragi ◽  
Belinauli Teknika Lumban Gaol

The need for housing is more higher along with the times and this is also a factor to increasing for concrete needed for building  development. The more concrete that is produced, the more cement is needed for construction.Concrete is a composite material (mixture) of several materials, the main ingredient which consists of a mixture of cement, fine aggregate, coarse aggregate, water and or without other additives with a certain ratio. Utilization of waste carried out in this study is to utilize corn cobs waste which is commonly found in the outskirts of the city of Medan. By utilizing this waste, it is hoped that it can reduce the accumulation of corn agricultural waste and also increase public insight about how to treat corn cobs waste into other forms. In this study, a concrete trial was carried out by adding corn cobs ash waste to concrete which aims to find out whether corn cobs ash can increase the compressive strength of concrete with variations in the percentage of the mixture of 0%, 3%, 6%, and 9% of the cement weight. The compressive strength value of normal concrete (25.45MPa), while with the substitution of corn cob ash 3% (21.96 MPa), 6% (18.56MPa), and 9% (16.45MPa). So it can be concluded that the resulting compressive strength exceeds the planned compressive strength and the optimum substitution value of corn cobs varian is at the 3% variant, namely 21.96 MPa.


2021 ◽  
Vol 878 (1) ◽  
pp. 012047
Author(s):  
R A Siregar ◽  
L E Hutabarat ◽  
S P Tampubolont ◽  
C C Purnomo

Abstract As a material of construction, concrete have a good compressive strength but low tensile strength. From the previous study, reducing the tensile weakness of the concrete using empty fruit bunch (EFB) of Palm for the concrete mix have a significant result. But in contrary, the use of this fiber decreases the compressive strength of concrete. This research aims to optimize a mixture of glass powders on EFB fiber as a solution to increase the compressive and tensile in strength of concrete as well. The fiber material requires pre condition treatment which is soaked in 10% NaOH for 6-10 hours, then is followed with drying for 24 hours and finally cutting into 4 cm pieces long. Using glass powder as mix design with fiber material which is substitute for fine aggregate in concrete. Variation of 0.25%, 0.5%, 0.75%, 1%, 1,25%, 1,5%, 1,75%, and 2% fiber material mix up with 10% glass powder used for concrete specimens with a diameter of 15 cm and a height of 30 cm at the age of 28 days testing. The results of this study shows an increase in the compressive and tensile strength of concrete compare to normal concrete. The optimum compressive increase 21.02% of normal concrete which is 24.87 MPa. Meanwhile the tensile strength an increase of 31,78% of normal concrete which is 3,11 MPa using 1% fibre and 10% of glass powder. Hence, using glass powder mix in EFB to increase compressive and tensile strength of concrete can be developed optimally in the future.


Sign in / Sign up

Export Citation Format

Share Document