scholarly journals Karstic aquifer vulnerability assessment methods and results at a test site (Apulia, southern Italy)

2009 ◽  
Vol 9 (4) ◽  
pp. 1461-1470 ◽  
Author(s):  
M. Polemio ◽  
D. Casarano ◽  
P. P. Limoni
Keyword(s):  
Test Site ◽  
Aquifer Vulnerability ◽  
Data Set ◽  
Intrinsic Vulnerability ◽  
Advantages And Disadvantages ◽  
General Terms ◽  
Karstic Features ◽  
Spatial Domains ◽  
Vulnerability Maps ◽  
Set Up

Abstract. Karstic aquifers are well known for their vulnerability to groundwater contamination. This is due to characteristics such as thin soils and point recharge in dolines, shafts, and swallow holes. In karstic areas, groundwater is often the only freshwater source. This is the case of the Apulia region (south-eastern Italy), where a large and deep carbonate aquifer, affected by karstic and fracturing phenomena, is located. Several methods (GOD, DRASTIC, SINTACS, EPIK, PI, and COP) for the assessment of the intrinsic vulnerability (Iv) were selected and applied to an Apulian test site, for which a complete data set was set up. The intrinsic vulnerability maps, produced using a GIS approach, show vulnerability from low to very high. The maximum vulnerability is always due to karstic features. A comparison approach of the maps is proposed. The advantages and disadvantages of each method are discussed. In general terms, three groups can be distinguished. The GOD method is useful for mapping large areas with high vulnerability contrasts. DRASTIC and SINTACS are "any-type aquifer" methods that have some limitations in applications to karstic aquifers, especially in the case of DRASTIC. EPIK, PI, and COP, which were designed to be applied to carbonate or karstic aquifers, supply affordable results, highly coherent with karstic and hydrogeological features, and reliable procedures, especially in the case of PI and COP. The latter appears simpler to apply and more flexible in considering the role of climatic parameters. If Iv of each method is considered, the highest variability is observed in cells in the neighbourhood of karstic features. In these spatial domains, additional efforts to define more reliable and global methods are required.

The Italian way to prevent groundwater contamination risk

2007 ◽  
Vol 2 (3) ◽  
Author(s):  
M. V. Civita ◽  
M. De Maio ◽  
A. Fiorucci
Keyword(s):  
Groundwater Contamination ◽  
Groundwater Vulnerability ◽  
Aquifer Vulnerability ◽  
National Council ◽  
National Guidelines ◽  
National Agency ◽  
Point Count ◽  
Italian Law ◽  
Special Project ◽  
Set Up

In the early 1980's the Italian scientific community, together with a number of institutional decision-makers, realized how urgent it was to protect natural and environmental resources. They agreed that an adequate level of scientifically organized knowledge allows the accurate planning and development of environmental systems through management and direction of the actual development process, without hindering it. Since the special project was first set up in 1984, as part of the GNDCI-CNR (National Group for the Defence against Hydrogeologic Disasters, of the Italian National Council of Research) scientific context, it has been the cardinal point of Research Line 4 “Assessment of Aquifer Vulnerability”. The problem of groundwater contamination was examined in this project for the very first time in Italy in an organic and extensive manner as a key for forecasting and prevention purposes. The Italian approaches to assessing and mapping groundwater vulnerability to contamination are essentially based on two main methodologies:- The GNDCI Basic Method a HCS (Hazard Contamination Source) type approach that can be used for any type of Italian hydrogeologic situation, even where there is a limited amount of data. A unified legend and symbols are also defined for each hydrogeologic level.- The SINTACS [Soggiacenza (depth to groundwater); Infiltrazione (effective infiltration); Non saturo (unsaturated zone attenuation capacity); Tipologia della copertura (soil/overburden attenuation capacity); Acquifero (saturated zone characteristics); Conducibilità (hydraulic conductivity); Superficie topografica (Slope)] method, a PCSM (Point Count System Model) developed for use prevalently in areas with good data base coverage. The methodological approaches described in this paper now make up the Italian standard which has been set in the recent very important Italian Law (152/99) and which has now been ratified in the national guidelines produced by ANPA, the Italian National Agency for Environment Protection. In this paper the structure of the Research Line, the progress obtained by the 21 Research units (over 100 researchers) in 20 years of activity, the results gained etc. are briefly highlighted.

Handheld Laser Scanner Research

2019 ◽  
Vol 952 (10) ◽  
pp. 47-54
Author(s):  
A.V. Komissarov ◽  
A.V. Remizov ◽  
M.M. Shlyakhova ◽  
K.K. Yambaev
Keyword(s):  
Point Cloud ◽  
Three Dimensional ◽  
Laser Scanner ◽  
Test Site ◽  
Optical Systems ◽  
Advantages And Disadvantages ◽  
Site Survey ◽  
Laser Scanners ◽  
Three Dimensional Models ◽  
The Stability

The authors consider hand-held laser scanners, as a new photogrammetric tool for obtaining three-dimensional models of objects. The principle of their work and the newest optical systems based on various sensors measuring the depth of space are described in detail. The method of simultaneous navigation and mapping (SLAM) used for combining single scans into point cloud is outlined. The formulated tasks and methods for performing studies of the DotProduct (USA) hand-held laser scanner DPI?8X based on a test site survey are presented. The accuracy requirements for determining the coordinates of polygon points are given. The essence of the performed experimental research of the DPI?8X scanner is described, including scanning of a test object at various scanner distances, shooting a test polygon from various scanner positions and building point cloud, repeatedly shooting the same area of the polygon to check the stability of the scanner. The data on the assessment of accuracy and analysis of research results are given. Fields of applying hand-held laser scanners, their advantages and disadvantages are identified.

Perceived Advantages and Disadvantages of Nonsmoking Sections in Restaurants: Topics to Communicate to Restaurateurs

1989 ◽  
Vol 9 (4) ◽  
pp. 299-304 ◽  
Author(s):  
Gerardo Marin ◽  
Raymond J. Gamba
Keyword(s):  
San Francisco ◽  
Advantages And Disadvantages ◽  
Set Up

Results from interviews with 315 restaurateurs in San Francisco are reported on their perceptions of the advantages and disadvantages of having a nonsmoking section in their restaurants. The major advantage of having a nonsmoking section independent of whether one is present is to please customers. The most commonly mentioned disadvantage for those restaurants with nonsmoking sections is the fact that it is inconvenient to clients' seating preferences primarily because it breaks up dining parties. Efforts at convincing restaurateurs to set up nonsmoking sections may be directed at pointing out savings in cleaning, labor, insurance, and the improvement of the health of their employees together with meeting clients' desires.

Colonial Origins of Maoist Insurgency in India

2017 ◽  
Vol 62 (10) ◽  
pp. 2232-2274 ◽  
Author(s):  
Shivaji Mukherjee
Keyword(s):  
Ethnic Inequality ◽  
Long Term Effects ◽  
Security Threat ◽  
Data Set ◽  
Internal Security ◽  
New Instrument ◽  
Maoist Insurgency ◽  
Rule Set ◽  
Set Up ◽  
Indirect Rule

What are the long-term effects of colonial institutions on insurgency? My article shows the historical origins of insurgency by addressing the puzzle of why the persistent Maoist insurgency, considered to be India’s biggest internal security threat, affects some districts along the central eastern corridor of India but not others. Combining archival and interview data from fieldwork in Maoist zones with an original district-level quantitative data set, I demonstrate that different types of British colonial indirect rule set up the structural conditions of ethnic inequality and state weakness that facilitate emergence of Maoist control. I address the issue of selection bias, by developing a new instrument for the British choice of indirect rule through princely states, based on the exogenous effect of wars in Europe on British decisions in India. This article reconceptualizes colonial indirect rule and also presents new data on rebel control and precolonial rebellions.

scholarly journals Use of routinely collected data on psychiatric in-patient care

2003 ◽  
Vol 9 (4) ◽  
pp. 300-307 ◽  
Author(s):  
Gyles Glover
Keyword(s):  
Mental Health ◽  
Set Covering ◽  
Services Research ◽  
Data Set ◽  
Research Issues ◽  
Wide Range ◽  
Policy Work ◽  
Data Source ◽  
Set Up ◽  
Service Data

Since the start of the National Health Service, data have been collected on admissions to psychiatric in-patient units, first as the Mental Health Enquiry, then as part of Hospital Episode Statistics. Some details have changed but many have stayed remarkably consistent. Published literature on the wide range of research and policy work undertaken using this data source is reviewed. Early work was central to the government's deinstitutionalisation policy in the early 1960s. Subsequent studies cover a wide range of epidemiological and health services research issues. A new statistical base, the Mental Health Minimum Data Set, covering individuals receiving all types of health care is currently being set up. This will supplement (but not replace) admission statistics.

scholarly journals Monitoring compliance with sulfur content regulations of shipping fuel by in situ measurements of ship emissions

2015 ◽  
Vol 15 (17) ◽  
pp. 10087-10092 ◽  
Author(s):  
L. Kattner ◽  
B. Mathieu-Üffing ◽  
J. P. Burrows ◽  
A. Richter ◽  
S. Schmolke ◽  
...  
Keyword(s):  
Sulfur Content ◽  
Air Pollutant ◽  
Monitoring Site ◽  
Data Set ◽  
The North ◽  
Position Data ◽  
Gas Measurements ◽  
Set Up ◽  
Carbon Dioxide Co2

Abstract. In 1997 the International Maritime Organisation (IMO) adopted MARPOL Annex VI to prevent air pollution by shipping emissions. It regulates, among other issues, the sulfur content in shipping fuels, which is transformed into the air pollutant sulfur dioxide (SO2) during combustion. Within designated Sulfur Emission Control Areas (SECA), the sulfur content was limited to 1 %, and on 1 January 2015, this limit was further reduced to 0.1 %. Here we present the set-up and measurement results of a permanent ship emission monitoring site near Hamburg harbour in the North Sea SECA. Trace gas measurements are conducted with in situ instruments and a data set from September 2014 to January 2015 is presented. By combining measurements of carbon dioxide (CO2) and SO2 with ship position data, it is possible to deduce the sulfur fuel content of individual ships passing the measurement station, thus facilitating the monitoring of compliance of ships with the IMO regulations. While compliance is almost 100 % for the 2014 data, it decreases only very little in 2015 to 95.4 % despite the much stricter limit. We analysed more than 1400 ship plumes in total and for months with favourable conditions, up to 40 % of all ships entering and leaving Hamburg harbour could be checked for their sulfur fuel content.

An Approach for Efficient CFD Simulations of an Ejector Air Injection System for Active Aerodynamic Compressor Stabilization

2017 ◽  
Author(s):  
Sebastian Brehm ◽  
Felix Kern ◽  
Jonas Raub ◽  
Reinhard Niehuis
Keyword(s):  
Large Scale ◽  
Armed Forces ◽  
Air Injection ◽  
Injection System ◽  
Cfd Simulations ◽  
Data Set ◽  
Numerical Effort ◽  
Enhance Efficiency ◽  
Set Up ◽  
Novel Concept

The Institute of Jet Propulsion at the University of the German Federal Armed Forces Munich has developed and patented a novel concept of air injection systems for active aerodynamic stabilization of turbo compressors. This so-called Ejector Injection System (EIS) utilizes the ejector effect to enhance efficiency and impact of the aerodynamic stabilization of the Larzac 04 two-spool turbofan engine’s LPC. The EIS design manufactured recently has been subject to CFD and experimental pre-investigations in which the expected ejector effect performance has been proven and the CFD set-up has been validated. Subsequently, optimization of the EIS ejector geometry comes into focus in order to enhance its performance. In this context, CFD parameter studies on the influence of in total 16 geometric and several aerodynamic parameters on the ejector effect are required. However, the existing and validated CFD set-up of the EIS comprises not only the mainly axisymmetric ejector geometry but also the highly complex 3D supply components upstream of the ejector geometry. This is hindering large scale CFD parameter studies due to the numerical effort required for these full 3D CFD simulations. Therefore, an approach to exploit the overall axissymmetry of the ejector geometry is presented within this paper which reduces the numerical effort required for CFD simulations of the EIS by more than 90%. This approach is verified by means of both experimental results as well as CFD predictions of the full 3D set-up. The comprehensive verification data set contains wall pressure distributions and the mass flow rates involved at various Aerodynamic Operating Points (AOP). Furthermore, limitations of the approach are revealed concerning its suitability e.g. to judge the response of the attached compressor of future EIS designs concerning aerodynamic stability or cyclic loading.

scholarly journals FINE REGISTRATION OF KILO-STATION NETWORKS - A MODERN PROCEDURE FOR TERRESTRIAL LASER SCANNING DATA SETS

2016 ◽  
Vol XLI-B5 ◽  
pp. 485-492
Author(s):  
J.-F. Hullo
Keyword(s):  
Laser Scanning ◽  
Laser Scanner ◽  
Data Sets ◽  
Data Set ◽  
Information Models ◽  
3D Network ◽  
Laser Scanners ◽  
Building Information ◽  
Set Up ◽  
Fine Registration

We propose a complete methodology for the fine registration and referencing of kilo-station networks of terrestrial laser scanner data currently used for many valuable purposes such as 3D as-built reconstruction of Building Information Models (BIM) or industrial asbuilt mock-ups. This comprehensive target-based process aims to achieve the global tolerance below a few centimetres across a 3D network including more than 1,000 laser stations spread over 10 floors. This procedure is particularly valuable for 3D networks of indoor congested environments. In situ, the use of terrestrial laser scanners, the layout of the targets and the set-up of a topographic control network should comply with the expert methods specific to surveyors. Using parametric and reduced Gauss-Helmert models, the network is expressed as a set of functional constraints with a related stochastic model. During the post-processing phase inspired by geodesy methods, a robust cost function is minimised. At the scale of such a data set, the complexity of the 3D network is beyond comprehension. The surveyor, even an expert, must be supported, in his analysis, by digital and visual indicators. In addition to the standard indicators used for the adjustment methods, including Baarda’s reliability, we introduce spectral analysis tools of graph theory for identifying different types of errors or a lack of robustness of the system as well as <i>in fine</i> documenting the quality of the registration.

scholarly journals Standard geomagnetic observatory data in tectonomagnetism: case study related to the M 5.7 Timisoara, Romania, earthquake

1997 ◽  
Vol 40 (2) ◽  
Author(s):  
M. Popeskov
Keyword(s):  
Geomagnetic Field ◽  
Large Scale ◽  
Regional Scale ◽  
Extensive Study ◽  
Field Variation ◽  
Regional Effect ◽  
Data Set ◽  
Small Magnitude ◽  
Observatory Data ◽  
Set Up

There has recently been much discussion of large-scale interactions of fault zones and the influence of large-scale processes in the preparation and triggering of earthquakes. As a consequence, an official recommendation was issued to set up observational networks at regional scale. In this context, the existing network of standard geomagnetic observatories might play a more important role in future tectonomagnetic studies. The data from standard geomagnetic observatories are basically not appropriate for the detection of small-magnitude and, in most cases, spatially very localized geomagnetic field changes. However, their advantage is a continuity in a long-time period which enables the study of regional tectonomagnetic features and long-term precursory changes. As the first step of a more extensive study aimed at examining the features of observatory data for this purpose, a three-year data set from five European observatories has been analyzed. Some common statistical procedures have been applied along with a simple difference technique and multivariate linear regression to define local geomagnetic field changes. The distribution of M ³ 4.5 earthquakes in Europe, in a corresponding period, was also taken into account. No pronounced field variation, related in time to the M 5.7 Timisoara (Romania) earthquake on July 12, 1991, was found at Grocka observatory at about 80 km from the earthquake epicenter. However, an offset in level of the differences in declination which include Grocka observatory, not seen in the case of differences between other observatories, could be associated with a possible regional effect of the M 4.8 earthquake which occurred in September 1991 at about 70 km SE from Grocka.

scholarly journals First Application of the Integrated Karst Aquifer Vulnerability (IKAV) method. Potential and Actual vulnerability in Yucatan, Mexico

2021 ◽  
Author(s):  
Miguel Moreno-Gómez ◽  
Carolina Martínez-Salvador ◽  
Rudolf Lied ◽  
Catalin Stefan ◽  
Julia Pacheco
Keyword(s):  
Transport Model ◽  
Karst Aquifer ◽  
Theoretical Models ◽  
Groundwater Vulnerability ◽  
Aquifer Vulnerability ◽  
Environmental Damage ◽  
Integrated Method ◽  
Support Tools ◽  
Vulnerability Maps ◽  
Water Resources Protection

Abstract. Groundwater vulnerability maps are important decision support tools for water resources protection against pollution and helpful to minimize environmental damage. However, these tools carry a high subjectivity along the multiple steps taken for the development of such maps. Additionally, the theoretical models on which they are based do not consider important parameters such as pollutant concentration or pollutant residence time in a given section of the aquifer, solely focusing the analysis on a theoretical travel time from a release point towards a target. In this work, an integrated methodology for the evaluation of potential (intrinsic) and actual vulnerability is presented. This integrated method, named IKAV, was developed after the analysis of several study cases and the application of multiple intrinsic groundwater vulnerability methods in a selected study area. Also, a solute transport model served as the basis to define additional parameters for vulnerability analysis for areas severely affected by anthropogenic practices. A defined workflow and several criteria for parameters and attributes selection, rating and weighting assignment, and vulnerability classification are presented. The first application of the IKAV method was carried out in the Yucatan karst, demonstrating to be a reliable method for vulnerability estimation. Results demonstrated the scope of the IKAV method to highlight important regional conditions, minimizing the subjectivity, and expanding the analysis of vulnerability.

Sign in / Sign up

Export Citation Format

Share Document