Flotation-Dissolution-Spectrophotometric Determination of Phorate in Various Environmental Samples

2020 ◽  
Vol 33 (1) ◽  
pp. 18-23
Author(s):  
Harshita Sharma ◽  
Anushree Saha ◽  
Chhaya Bhatt ◽  
Kalpana Wani ◽  
Ajay Kumar Sahu ◽  
...  
Keyword(s):  
Standard Deviation ◽  
Spectrophotometric Determination ◽  
Acidic Medium ◽  
Molar Absorptivity ◽  
Ammonium Molybdate ◽  
Organophosphate Pesticide ◽  
Organic Layers ◽  
Relative Standard ◽  
Ion Associate

The proposed method is based on flotation–dissolution an easy, impressible, extractive spectrophotometric determination, explained for easy investigation of the organophosphate pesticide phorate (O,O-diethyl S-[ethylthiomethyl] phosphorodithioate) on trace levels. A molybdophospho complex is generated when prorate is treated with ammonium molybdate in acidic medium. As an ion associate complex with methylene blue the complex is present in between of the water and organic layers which is extracted and then dissolved with acetone. The greenish blue complex produced show absorption maxima at 660 nm. Beer’s law range is found to be 0.5 to 16 µg per 10 ml for phorate. The molar absorptivity is 0.989×103 L mol-1 cm-1 and sandell’s sensitivity is 1.00×10-5 µg cm-2. Also calculated the standard deviation and relative standard deviation for the above method were ±0.006 and 1.95% respectively. The method has been applied and checked for the determination of phorate in water, soil and vegetables.

scholarly journals Flotation-Spectrophotometric Method for the Determination of Aluminium ion Using Xylenol Orange

2011 ◽  
Vol 8 (4) ◽  
pp. 1528-1535 ◽  
Author(s):  
F. Nekouei ◽  
Sh. Nekouei
Keyword(s):  
Standard Deviation ◽  
Spectrophotometric Method ◽  
Calibration Curve ◽  
Limit Of Detection ◽  
Xylenol Orange ◽  
Molar Absorptivity ◽  
Relative Standard ◽  
Ion Associate ◽  
Sensitive Method

A simple, fast, reproducible and sensitive method for the flotation- spectrophotometric determination of Al3+is reported. The apparent molar absorptivity (ε) of the ion associate was determined to be 8.35×104L mol-1cm-1. The calibration curve was linear in the concentration range of 1.0-50 ng mL-1of Al3+with a correlation coefficient of 0.9997. The limit of detection (LOD) was 0.621 ng mL. The relative standard deviation (RSD) at 10 and 30 ng mL-1of aluminium were 1.580 and 2.410% (n=7) respectively. The method was applied for measuring the amount of aluminium in water samples.

Spectrophotometric Determination of Boron in Dates of Some Cultivars Grown in Saudi Arabia

1993 ◽  
Vol 76 (3) ◽  
pp. 601-603 ◽  
Author(s):  
A A Al-Warthan ◽  
S S Al-Showiman ◽  
S A Al-Tamrah ◽  
A A BaOsman
Keyword(s):  
Saudi Arabia ◽  
Standard Deviation ◽  
Relative Standard Deviation ◽  
Spectrophotometric Determination ◽  
Spectrophotometric Method ◽  
Molar Absorptivity ◽  
Relative Standard ◽  
Sensitive Spectrophotometric Method

Abstract The formation of a red complex between boron and the quinalizarin reagent was investigated and used as the basis for a simple and sensitive spectrophotometric method for boron in date cultivars. At 620 nm, the absorbance was linear (r= 0.999) over the 0.25-2.5 μg/mL concentration range. The molar absorptivity was found to be 2.23 x 103mol-1cm-1 and the relative standard deviation for 10 replicates (1.0 μg/mL) was 0.97%.

Spectrophotometric Method for Microdetermination of Nitrogen in Kjeldahl Digest

1989 ◽  
Vol 72 (6) ◽  
pp. 953-956 ◽  
Author(s):  
Muljibhai B Devani ◽  
Chamanlal J Shishoo ◽  
Shailesh A Shah ◽  
Bhanubhai N Suhagia
Keyword(s):  
Standard Deviation ◽  
Nitrogen Content ◽  
Spectrophotometric Method ◽  
Acidic Medium ◽  
Molar Absorptivity ◽  
Nitrogen Compounds ◽  
Relative Standard ◽  
Kjeldahl Method ◽  
Aoac Method

Abstract A new spectrophotometric method for the determination of nitrogen in Kjeldahl digest has been developed. The method is based on the reaction of ammonia with acetylacetone-formaldehyde reagent in aqueous medium to yield yellow 3,5-diacetyl- 1,4-dihydrolutidine with a characteristic absorption maxima at 412 nm. The effect of several experimental variables on the determination of nitrogen was studied. The method was suitable for determination of nitrogen in acidic medium without interference from the usual catalysts employed for the digestion in Kjeldahl method. Lambert-Beer’s law is obeyed in the concentration range of 0.5-6.0 ng nitrogen/mL in the reaction mixture. The molar absorptivity in terms of nitrogen was 1.4 X 103L mol-1 cm-1. The standard deviation and relative standard deviation were ±0.0447 and ±0.896% (n = 10), respectively. The method is simple, rapid, and precise. A variety of carbocyclic and heterocyclic nitrogen compounds have been analyzed for nitrogen content. The results are comparable with those obtained by AOAC method, 47.021.

scholarly journals Development and validation of spectrophotometric method for phenylephrine hydrochloride estimation in nasal drops formulations

2008 ◽  
Vol 27 (2) ◽  
pp. 149 ◽  
Author(s):  
Ivana Savić ◽  
Goran Nikolić ◽  
Vladimir Banković
Keyword(s):  
Standard Deviation ◽  
Sodium Hydroxide ◽  
Relative Standard Deviation ◽  
Spectrophotometric Method ◽  
Molar Absorptivity ◽  
Dosage Forms ◽  
Phenylephrine Hydrochloride ◽  
Relative Standard ◽  
Development And Validation

Simple, accurate and reproducible UV-spectrophotometric method was developed and validated for the estimation of phenylephrine hydrochloride in pharmaceutical nasal drops formulations. Phenylephrine hydrochloride was estimated at 291 nm in 1 mol⋅dm-3 sodium hydroxide (pH 13.5). Beer’s law was obeyed in the concentration range of 10–100 μg⋅cm−3 (r2 = 0.9990) in the sodium hydroxide medium. The apparent molar absorptivity was found to be 1.63×103 dm3⋅mol−1⋅cm−1. The method was tested and validated for various parameters according to the ICH (International Conference on Harmonization) guidelines. The detection and quantitation limits were found to be 0.892 and 2.969 μg⋅cm−3, respectively. The proposed method was successfully applied for the determination of phenylephrine hydrochloride in pharmaceutical nasal drops formulations. The results demonstrated that the procedure is accurate, precise and reproducible (relative standard deviation < 1 %), while being simple, cheap and less time consuming, and hence can be suitably applied for the estimation of phenylephrine hydrochloride in different dosage forms.

scholarly journals A sensitive spectrophotometric determination of tadalafil in pharmaceutical preparations and industrial wastewater samples

2013 ◽  
Vol 10 (3) ◽  
pp. 1005-1013 ◽  
Author(s):  
Baghdad Science Journal
Keyword(s):  
Standard Deviation ◽  
Industrial Wastewater ◽  
Pharmaceutical Preparations ◽  
Pharmaceutical Formulations ◽  
Molar Absorptivity ◽  
Average Recovery ◽  
Relative Standard ◽  
Wastewater Samples ◽  
Sensitive Spectrophotometric Method

A simple, accurate, precise, rapid, economical and a high sensitive spectrophotometric method has been developed for the determination of tadalafil in pharmaceutical preparations and industrial wastewater samples, which shows a maximum absorbance at 204 nm in 1:1 ethanol-water. Beer's law was obeyed in the range of 1-7?g/ mL ,with molar absorptivity and Sandell ? s sensitivity of 0.783x105l/mol.cm and 4.97 ng/cm2respectively, relative standard deviation of the method was less than 1.7%, and accuracy (average recovery %) was 100 ± 0. 13. The limits of detection and quantitation are 0.18 and 0.54 µg .ml-1, respectively. The method was successfully applied to the determination of tadalafil in some pharmaceutical formulations (tablets) and industrial wastewater samples. The proposed method was validated by sensitivity and precision which proves suitability for the routine analysis of tadalafil in true samples.

scholarly journals Spectrophotometric Method for Determination of Paraquat in Food and Biological Samples

1997 ◽  
Vol 80 (2) ◽  
pp. 388-391 ◽  
Author(s):  
Ritu Kesari ◽  
Manish Rai ◽  
Vinay Kumar Gupta
Keyword(s):  
Standard Deviation ◽  
Metal Ions ◽  
Relative Standard Deviation ◽  
Alkaline Medium ◽  
Spectrophotometric Method ◽  
Biological Samples ◽  
Molar Absorptivity ◽  
Relative Standard ◽  
Sensitive Spectrophotometric Method

Abstract A sensitive spectrophotometric method was developed for determination of paraquat, a widely used herbicide. Paraquat was reduced with glucose in an alkaline medium, and the blue radical ion obtained was measured at 600 nm. Beer’s law was obeyed at 0.1–1.2 ppm paraquat. The molar absorptivity was 1.26 × 105 L mol-1 cm-1. The standard deviation and relative standard deviation were ± 0.007 and 2.0%, respectively, for 5 μg paraquat/10 mL analyzed over 7 days. The method was free from interference by other commonly used pesticides and metal ions. The method may be used to the determine paraquat in plants, fruits, grains, water, blood, and urine.

Hydroxyamidines as New Extracting Reagents for Spectrophotometric Determination of Cadmium with 4-(2-Pyridylazo)naphthol in Industrial Effluents, Coal, and Fly Ash

1993 ◽  
Vol 76 (3) ◽  
pp. 604-608 ◽  
Author(s):  
Sumon Chakravarty ◽  
Manas Kanti Deb ◽  
Rajendra Kumar Mishra
Keyword(s):  
Spectrophotometric Determination ◽  
Environmental Samples ◽  
Present Method ◽  
Industrial Effluents ◽  
Molar Absorptivity ◽  
Binary Complex ◽  
Matrix Interference ◽  
Relative Standard ◽  
The Common

Abstract A simple, sensitive, and selective extractive spectrophotometric method for the determination of cadmium in trace quantities with N1-hydroxy-N1,N2- diphenylbenzamidine (HDPBA) and 4-(2-pyridylazo) naphthol (PAN) is described. The method is based on the extraction of cadmium with HDPBA into chloroform at pH 9.0 ± 0.2 and simultaneous spectrophotometric determination wiith PAN. The binary Cd(ll)-HDPBA complex extracted into chloroform has a molar absorptivity of 1.96 x 104L/ mol/cm at λmax 400 nm. The sensitivity of the yellow Cd(ll)-HDPBA complex was increased remarkably by the addition of PAN to the binary complex. With 6 different hydroxyamidines tested, the red-orange complex in chloroform exhibited maximum absorbance at 530-550 nm, with molar absorptivity values of 3.2-5.6 x 104L/mol/cm. The method adheres to Beer’s law up to 1.5 μg cadmium/mL organic phase. The detection limit of the method is 0.02 μg Cd/mL. Investigations of the effect of foreign ions revealed that the present method is free from matrix interference of most of the common ions (e.g., Fe(lll), Ni(ll), Cu(ll), Mn(ll), V(V), Co(ll), Al(lll), Cu(ll), Mg(ll), and Mo(VI)). The relative standard deviation for 10 repetitive analyses of the metal was 1.4%. The validity of the method was tested successfully with various environmental samples.

Spectrophotometric Determination of Copper (II) with 5-Hydroxy-6-Mercapto-Benzo [a] Phenazine

2008 ◽  
Vol 59 (1) ◽  
pp. 3-7
Author(s):  
Aurora Reiss ◽  
Mihaela Mureseanu ◽  
Nicolae Muresan
Keyword(s):  
Spectrophotometric Determination ◽  
Molar Absorptivity ◽  
Molar Ratio ◽  
Variation Method ◽  
Ratio Method ◽  
Relative Standard ◽  
Analytical Reagent ◽  
Experimental Values ◽  
Determination Of Copper

5-Hydroxy-6-mercapto-benzo [a] phenazine (HMBP) is proposed as a sensitive and selective analytical reagent for the extractive spectrophotometric determination of copper (II). Copper reacts with HMBP to give a dark red complex which is soluble in chloroform. The composition of the CuII � HMBP complex is established as 1:2 by Job�s continuous variation method and molar ratio method. The instability constant of the complex calculated by Job�s relation for nonisomolar series is 4.65 . 10-9, at room temperature. The CuII-HMBP complex in chlorophorm shows a maximum absorbance at 495 nm, with molar absorptivity and Sandell�s sensitivity values of 7.39 . 103dm3 mol-1 cm-1 and 0.012 mg cm-2, respectively. Beer�s law is obeyed in the concentration range 0.67 - 26.90 mg mL-1 and the detection limit is 0.59 mg mL-1. A repetition of the method is checked by finding the relative standard deviation (RSD) at 1.00 mg mL-1 CuII of 0.6%. The method is successfully employed for the determination of copper (II) in environmental samples. The reliability of the method is assured by analysing the standard alloys and by inter-comparison of experimental values, using an atomic absorption spectrometer.

Spectrophotometric determination of trace amounts of phosphate in water and soil

2012 ◽  
Vol 66 (12) ◽  
pp. 2653-2658 ◽  
Author(s):  
S. Ganesh ◽  
Fahmida Khan ◽  
M. K. Ahmed ◽  
P. Velavendan ◽  
N. K. Pandey ◽  
...  
Keyword(s):  
Environmental Science ◽  
Medical Science ◽  
Selective Reduction ◽  
Phosphomolybdic Acid ◽  
Molar Absorptivity ◽  
Ammonium Molybdate ◽  
Blue Colour ◽  
Molybdenum Blue ◽  
Relative Standard

A simple spectrophotometric method has been developed for the determination of phosphate dissolved in soil and water. The method is based on the formation of phosphomolybdate with added ammonium molybdate followed by reduction with hydrazine in acidic medium. Orthophosphate and molybdate ions condense in acidic solution to give molybdophosphoric (phosphomolybdic) acid, which upon selective reduction (perhaps with hydrazinium sulphate) produces a blue colour, due to molybdenum blue of uncertain composition. The intensity of blue colour is proportional to the amount of phosphate. If the acidity at the time of reduction is 0.5 M in sulphuric acid and hydrazinium sulphate is the reductant, the resulting blue complex exhibits maximum absorption at 830 nm. The system obeys Lambert–Beer's law at 830 nm in the concentration range of 0.5–5 μg/mL of phosphate with a relative standard deviation (RSD) of 0.1% and correlation coefficient of 0.99. Molar absorptivity was determined to be 2.9 × 104 L mol–1 cm–1 at 830 nm. The method is also applicable for the determination of phosphate in nuclear reprocessing plants, medical science, clinical science, agriculture, metallurgy and environmental science.

scholarly journals Colorimetric Determination of Paracetamol Using 9-Chloroacridine Reagent: Application to Pharmaceutical Formulations

2020 ◽  
Vol 63 (2) ◽  
pp. 71-78
Author(s):  
Firas Hassan Awad
Keyword(s):  
Standard Deviation ◽  
Pharmaceutical Formulations ◽  
Extraction Process ◽  
Molar Absorptivity ◽  
Colorimetric Determination ◽  
Average Recovery ◽  
Relative Standard ◽  
Recovery Percentage ◽  
The Stability

This paper aims to develop a simple, sensitive and accurate spectrophotometric method for quantitative determination of paracetamol in aqueous medium. The method is based on the reaction between the hydrolyzed paracetamol and 9-chloroacridine reagent (9-CA). The spectra of the product show maximum absorption at 436 nm. Beer's law is obeyed in the concentration range of 0.25-11 µg/mL with molar absorptivity value 5.3x103 L/mol/cm. The average recovery percentage (Rec%) is 99.27% and relative standard deviation (RSD) is :: 2.82%. In addition, the stability constant has been determined and the reaction mechanism is proposed. The method has been applied successfully for the assay of paracetamol in pharmaceutical formulations. It is found that the method does not require extraction process and it agree well with British pharmacopeia.    

Sign in / Sign up

Export Citation Format

Share Document