scholarly journals Process Design of Superplastic Forming/Diffusion Bonding by Using Design of Experiment

2007 ◽  
Vol 16 (2) ◽  
pp. 144-149 ◽  
Keyword(s):  
Design Of Experiment ◽  
Process Design ◽  
Diffusion Bonding ◽  
Superplastic Forming

QUANTIFYING THE EFFECTS OF FUEL COMPOSITIONS AND PROCESS VARIABLES ON PLANAR SURFACE AREA AND SPRAY NONUNIFORMITY VIA COMBINED MIXTURE-PROCESS DESIGN OF EXPERIMENT

2017 ◽  
Vol 27 (8) ◽  
pp. 707-722 ◽  
Author(s):  
Longfei Chen ◽  
Liuyang Feng ◽  
Zhixin Liu ◽  
Guangze Li ◽  
Yanfei Li ◽  
...  
Keyword(s):  
Surface Area ◽  
Design Of Experiment ◽  
Process Design ◽  
Process Variables ◽  
Planar Surface

scholarly journals Superplastic Forming and Reaction Diffusion Bonding Process of Hollow Structural Component for Mg-Gd-Y-Zn-Zr Rare Earth Magnesium Alloy

Metals ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 152
Author(s):  
Peng Peng ◽  
Shaosong Jiang ◽  
Zhonghuan Qin ◽  
Zhen Lu
Keyword(s):  
Mechanical Properties ◽  
Diffusion Bonding ◽  
Structural Component ◽  
Bonding Temperature ◽  
Reaction Diffusion ◽  
Superplastic Forming ◽  
Tensile Tests ◽  
Interface Roughness ◽  
Size Growth ◽  
Cu Interlayer

This work fabricated a double hollow structural component of Mg-8.3Gd-2.9Y-0.8Zn-0.2Zr alloy by superplastic forming (SPF) and reaction-diffusion bonding (RDB). The superplastic characteristic and mechanical properties of Mg-8.3Gd-2.9Y-0.8Zn-0.2Zr alloy sheets at 250–450 °C were studied. Tensile tests showed that the maximum elongation of tensile specimens was about 1276.3% at 400 °C under a strain rate of 1 × 10−3 s−1. Besides, the effect of bonding temperature and interface roughness on microstructure and mechanical properties of the reaction diffusion-bonded joints with a Cu interlayer was investigated. With the increase of temperature, the diffusion coefficient of Cu increases, and the diffusion transition region becomes wider, leading to tightening bonding of the joint. However, the bonding quality of the joint will deteriorate due to grain size growth at higher temperatures. Shear tests showed that the highest strength of the joints was 152 MPa (joint efficiency = 98.7%), which was performed at 460 °C.

Problems and Promises of Developing Integral Technology of Superplastic Forming and Diffusion Bonding (SPF/DB)

1994 ◽  
Vol 170-172 ◽  
pp. 737-742 ◽  
Author(s):  
Oscar A. Kaibyshev ◽  
Ramil Ya. Lutfullin ◽  
Rinat V. Safiullin ◽  
S.N. Fatkullin
Keyword(s):  
Diffusion Bonding ◽  
Superplastic Forming ◽  
And Diffusion

Superplastic forming and diffusion bonding of Inconel 718

1984 ◽  
Vol 21 (1) ◽  
pp. 61-64 ◽  
Author(s):  
W. T. Chandler ◽  
A. K. Ghosh ◽  
W. M. Mahoney
Keyword(s):  
Diffusion Bonding ◽  
Inconel 718 ◽  
Superplastic Forming ◽  
And Diffusion
Sign in / Sign up

Export Citation Format

Share Document