scholarly journals The experience of implementation of polymer flooding technology at Zaburunye oil filed as a method for developing mature fields

2021 ◽  
Vol 3 (1) ◽  
pp. 29-42
Author(s):  
M. Sh. Musayev ◽  
D. A. Musharova ◽  
B. Zh. Zhappasbayev ◽  
E. K. Orynbassar
Keyword(s):  
Oil Recovery ◽  
High Water ◽  
Volatile Oil ◽  
Polymer Flooding ◽  
Oil Field ◽  
Recovery Factor ◽  
Wide Range ◽  
Secondary Oil Recovery ◽  
High Water Cut Stage ◽  
High Water Cut

In conditions of high depletion of oil fields and volatile oil prices, methods of enhanced oil recovery are becoming especially relevant, the use of which contributes to an increase in the oil recovery factor in addition to the use of secondary oil recovery methods. One of the technologies allowing to increase the oil recovery factor is polymer flooding technology, the distinctive advantage of which in comparison with other chemical methods is a wide range of application conditions and design variability during implementation. This paper presents the results of the application of polymer flooding technology in the oil field of Kazakhstan Zaburunye, which is in the high water-cut stage. To determine the strategy for the further implementation of polymer flooding technology and in order to find the optimal predictive development options, calculations were carried out on the developed hydrodynamic model.

On the Feasibility of Applying Electric Field to Increase Oil Recovery in Old Oil Field

2014 ◽  
Vol 900 ◽  
pp. 677-680
Author(s):  
Chun Hong Nie
Keyword(s):  
Electric Field ◽  
Oil Recovery ◽  
Water Injection ◽  
High Water ◽  
Oil Field ◽  
Thin Layers ◽  
Stable Yield ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

This paper has discussed the characteristics, roles, feasibility and obvious effects of the technology by applying electric field to enhance oil recovery when the oil field is in high water cut stage and super high water cut stage. In view that most oil wells in old oil field have entered into the super high water cut production, the remaining oil in the main reservoir is in fragmented distribution with poor results of water injection and new reserves of oil mostly have a low penetration rate and are thin layers of poor physical properties, the use of the direct current field in period of high water cut is the best policy to achieve high and stable yield and is fairly promising.

scholarly journals Optimization of reinjection treatment technology for oilfield wastewater in Longdong area

2020 ◽  
Vol 194 ◽  
pp. 04046
Author(s):  
Xiulan Zhu ◽  
Yanlong Ran ◽  
Wenjie Guo ◽  
Ke Gai ◽  
Yanju Li ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Solid Phase ◽  
Sewage Treatment ◽  
Water Injection ◽  
Oil Production ◽  
High Water ◽  
Oil Field ◽  
Treatment Technology ◽  
Water Separation ◽  
High Water Cut

With the long-term water injection development of Longdong oilfields, most of the oilfield blocks have been fully in the mid-high water cut period, and the amount of oil production wastewater is increasing year by year. In order to prevent the waste of resources and energy of oil production sewage, the oil production sewage after reaching the standard is treated for reinjection, which will ensure the sustainable development of the oil field. Oil production wastewater contains crude oil, solid-phase suspended solids and other pollutants, with high salinity, and problems such as difficulty in oil-water separation, sludge, scaling and corrosion. The sewage treatment system uses a multifunctional water treatment device to effectively remove oil and filter through the “special microorganism + air flotation + filtration” process, and build a sludge sewage tank for sludge discharge and backwashing. The reformed oil recovery wastewater reinjection treatment technology turns “sewage” into “clear flow”, reduces operating costs, improves wastewater treatment efficiency, and meets the water quality requirements of oilfield reinjection water.

scholarly journals A Novel Assisted Gas–Oil Countercurrent EOR Technique for Attic Oil in Fault-Block Reservoirs

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 402
Author(s):  
Kang Ma ◽  
Hanqiao Jiang ◽  
Junjian Li ◽  
Rongda Zhang ◽  
Kangqi Shen ◽  
...  
Keyword(s):  
Production Process ◽  
Oil Recovery ◽  
Production Efficiency ◽  
High Water ◽  
Gas Oil ◽  
Fault Block ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Gas Channeling ◽  
Water Cut

As the mature oil fields have stepped into the high water cut stage, the remaining oil is considered as potential reserves, especially the attic oil in the inclined fault-block reservoirs. A novel assisted gas–oil countercurrent technique utilizing gas oil countercurrent (GOC) and water flooding assistance (WFA) is proposed in this study to enhance the remaining oil recovery in sealed fault-block reservoirs. WFA is applied in our model to accelerate the countercurrent process and inhibit the gas channeling during the production process. Four comparative experiments are conducted to illustrate enhanced oil recovery (EOR) mechanisms and compare the production efficiency of assisted GOC under different assistance conditions. The results show that WFA has different functions at different stages of the development process. In the gas injection process, WFA forces the injected gas to migrate upward and shortens the shut-in time by approximately 50% and the production efficiency improves accordingly. Compared with the basic GOC process, the attic oil swept area is extended 60% at the same shut-in time condition and secondary gas cap forms under the influence of WFA. At the production stage, the WFA and secondary gas cap expansion form the bi-directional flooding. The bi-directional flooding also displaces the bypassed oil and replaced attic oil located below the production well, which cannot be swept by the gas cap expansion. WFA inhibits the gas channeling effectively and increases the sweep factor by 26.14% in the production stage. The oil production increases nearly nine times compared with the basic GOC production process. The proposed technique is significant for the development of attic oil in the mature oil field at the high water cut stage.

Study on Technical Limits of Single-Pipe Concatenation Gathering Process during High Water-Cut Stage

2013 ◽  
Vol 295-298 ◽  
pp. 3323-3327
Author(s):  
Li Xin Wei ◽  
Xin Peng Le ◽  
Yun Xia Fu ◽  
Zhi Hua Wang ◽  
Yu Wang
Keyword(s):  
Oil Recovery ◽  
High Water ◽  
Temperature Limit ◽  
Tertiary Oil Recovery ◽  
Recovery Technique ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut ◽  
Single Pipe ◽  
Oil Gas

In order to optimize the gathering system and reduce the energy consumption in the production, single-pipe concatenation process has been widely used after the tertiary oil recovery technique is applied and development enters into high water cut stage in the oilfield. Aiming at condensate oil in gathering pipeline and obvious increase of the high circle pressure wells in the operation of the process, the adaption relationship between oil gathering pipeline size and flow, as well as the temperature limit of the gathering system start are studied, through the hydraulic and thermodynamic calculations of oil-gas-water multiphase flow. It has directive function for making effective schemes to solve the production problems caused by the high back pressure of wells.

Research on Methods of Separate Stratum Injection Allocation in High Water Cut Stage

2013 ◽  
Vol 868 ◽  
pp. 645-650
Author(s):  
Lin Li
Keyword(s):  
Material Balance ◽  
High Water ◽  
Small Error ◽  
Oil Field ◽  
Petroleum Reservoir ◽  
Injection Wells ◽  
Single Well ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

The parameters of reservoir impact all the sectors of oilfield developing after flood development, so methods of separate stratum injection allocation are researched for forecasting the petroleum reservoir performance accurately. The methods of separate stratum injection allocation are significative for remaining oil distribution, injection allocation of interval and the level of exploitation and administration in high water cut stage. First, we should derive injection-withdrawal ratio (IWR), gradient of pressure and water cut by material balance equation.The injection allocation of single well,injection wells and property of interval are determined by the research of split coefficient.We find the reservoir small error, lower water cut, high degree of reservoir recovery by anaysising the results of separate stratum injection allocation.The results show that separate stratum injection allocation is scientific and reasonable, simple and applied for the oil field in high water cut stage.

scholarly journals Experimental study on waterflooding development of low-amplitude reservoir with big bottom water

2021 ◽  
Author(s):  
Yanlai Li ◽  
Jie Tan ◽  
Songru Mou ◽  
Chunyan Liu ◽  
Dongdong Yang
Keyword(s):  
Bottom Water ◽  
Water Injection ◽  
Water Reservoir ◽  
High Water ◽  
Recovery Factor ◽  
Low Viscosity ◽  
Well Spacing ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

AbstractFor offshore reservoirs with a big bottom water range, the water cut rises quickly and soon enters the ultra-high water cut stage. After entering the ultra-high water cut stage, due to the influence of offshore production facilities, there are few potential tapping measures, so it is urgent to explore the feasibility study of artificial water injection development. The quasi-three-dimensional and two-dimensional displacement experiments are designed using the experimental similarity criteria according to the actual reservoir parameters. Several experimental schemes are designed, fluid physical properties, interlayer distribution, and development mode according to the actual reservoir physical properties. Through the visualization of experimental equipment, the bottom water reservoir is visually stimulated. The displacement and sweep law of natural water drive and artificial water injection in bottom water reservoir with or without an interlayer, different viscosity, and different well spacing is analyzed. The following conclusions are obtained: (1) For reservoirs with a viscosity of 150 cp. The recovery factor after water injection is slightly higher than before water injection. However, the recovery factor is lower than that without injection production. The reason is that the increment of injection conversion is limited to reduce one production well after injection conversion. (2) For reservoirs with a viscosity of 30 cp. The recovery factor after injection is 39.8%, which is slightly higher than 38.9% without injection. (3) For reservoirs with a viscosity of 150 cp. In the case of the interlayer. The recovery factor after injection is 30.7%, which is significantly higher than 24.8% without injection. (4) After the well spacing of the low-viscosity reservoir is reduced, the recovery factor reaches 46.1%, which is higher than 38.9% of the non-infill scheme. After the infill well in a low-viscosity reservoir is transferred to injection, the recovery factor is 45.6%, which has little change compared with non-injection, and most of the cumulative production fluid is water. The feasibility and effect of water flooding in a strong bottom water reservoir are demonstrated. This study provides the basis for the proposal of production well injection conversion and the adjustment of production parameters in the highest water cut stage of a big bottom water reservoir.

scholarly journals Techniques for improving the water-flooding of oil fields during the high water-cut stage

2019 ◽  
Vol 74 ◽  
pp. 69 ◽  
Author(s):  
Kuiqian Ma ◽  
Ao Li ◽  
Shuhao Guo ◽  
Jieqiong Pang ◽  
Yongchao Xue ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Water Injection ◽  
Reduction Rate ◽  
High Water ◽  
Water Flooding ◽  
Variable Intensity ◽  
Remaining Oil ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

The multi-layer co-exploitation method is often used in offshore oilfields because of the large spacing between the injection and production wells. As oilfields gradually enter the high water-cut stage, the contradiction between the horizontal and vertical directions becomes more prominent, and the distribution of the remaining oil is more complex. Oilfields are facing unprecedented challenges in further enhancing oil recovery. Using oilfield A, which is in the high water-cut stage, as the research object, we compiled a detailed description of the remaining oil during the high water-cut stage using the information collected during the comprehensive adjustment and infilling of the oilfield. In addition various techniques for tapping the potential reservoir, stabilizing the oil, and controlling the water were investigated. A set of key techniques for the continuous improvement of the efficiency of water injection after comprehensive adjustment of high water-cut fields was generated. Based on the determined configuration of the offshore deltaic reservoir, a set of detailed descriptive methods and tapping technology for extracting the remaining oil in the offshore high water-cut oilfield after comprehensive adjustment was established. By considering the equilibrium displacement and using a new quantitative characterization method that includes displacement, a new technique for determining the quantity of water that needs to be injected into a stratified injection well during the high water-cut stage was established. Based on the principle of flow field intensity reconfiguration, a linear, variable-intensity, alternating injection and withdrawal technique was proposed. With the application of this series of techniques, the increase in the water content was controlled to within 1%, the natural reduction rate was controlled to within 9%, and the production increased by 1.060 × 107 m3.

scholarly journals Experimental Study on the Properties and Displacement Effects of Polymer Surfactant Solution

2013 ◽  
Vol 2013 ◽  
pp. 1-6
Author(s):  
Ke-Liang Wang ◽  
Lei-Lei Zhang ◽  
Xue Li ◽  
Yang-Yang Ming
Keyword(s):  
Oil Recovery ◽  
Surfactant Solution ◽  
High Water ◽  
Water Flooding ◽  
Displacement Effect ◽  
Molecular Weight Polymer ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Polymer Surfactant ◽  
Displacement Effects

Based on the characteristics of oil reservoirs and the requirements of further enhancing oil recovery at high water cut stage of Pubei Oilfield, the displacement performance of polymer surfactant is evaluated. Reasonable injection parameters and oil displacement effects after water flooding are also researched. Compared with conventional polymer with intermediate molecular weight, polymer surfactant has the properties of higher viscosity at low concentration condition and lower interfacial tension. Laboratory experiments indicate that the displacement effect of polymer surfactant is much better than that of conventional polymer at a slug size of 0.57 PV. The oil recovery of polymer surfactant increases by more than 10% after water flooding. Considering the actual situation of low-permeability of Pubei Oilfield reservoirs, the system viscosity of 30 mPa·s is chosen. The corresponding concentration of Type III polymer surfactant is 600 mg/L and the injected slug is 0.57 PV and the oil recovery can be increased by 11.69%.

Sign in / Sign up

Export Citation Format

Share Document