The Choice of the Propeller

1966 ◽  
Vol 3 (02) ◽  
pp. 158-171
Author(s):  
J. D. van Manen
Keyword(s):  
Test Data ◽  
Model Test ◽  
Testing Technique ◽  
Full Size ◽  
Cavitation Inception ◽  
Different Types

In this paper the four main requirements for a propeller are dealt with. These requirements concern efficiency, cavitation, propeller-excited forces and stopping abilities. In a propeller diagram the characteristic efficiency curves for different conditions are explained. A comparison of the optimum efficiencies for various types of propulsors is given, and the applications on a 130,000-dwt tanker are considered. Cavitation-inception curves both for a specific propeller and for systematic propeller series are discussed. Predicted torque and thrust fluctuations, based on model-test data, and the results of measurements on the full-size ship are compared. Finally a quasi-steady testing technique, developed to analyze different types of stopping maneuvers, is described.

Joint High Speed Sealift (JHSS) Segmented Model Test Data Analysis and Validation of Numerical Simulations

2012 ◽  
Author(s):  
Dominic Piro ◽  
Kyle A. Brucker ◽  
Thomas T. O'Shea ◽  
Donald Wyatt ◽  
Douglas Dommermuth ◽  
...  
Keyword(s):  
Data Analysis ◽  
Numerical Simulations ◽  
Test Data ◽  
Model Test ◽  
High Speed ◽  
Segmented Model

Guidelines for CFD Simulations of Spar VIM

2013 ◽  
Author(s):  
Charles Lefevre ◽  
Yiannis Constantinides ◽  
Jang Whan Kim ◽  
Mike Henneke ◽  
Robert Gordon ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Test Data ◽  
Model Test ◽  
Model Tests ◽  
Full Scale ◽  
Mooring System ◽  
Time Step ◽  
Cfd Simulations ◽  
Scaled Model ◽  
Sway Motion

Vortex-Induced Motion (VIM), which occurs as a consequence of exposure to strong current such as Loop Current eddies in the Gulf of Mexico, is one of the critical factors in the design of the mooring and riser systems for deepwater offshore structures such as Spars and multi-column Deep Draft Floaters (DDFs). The VIM response can have a significant impact on the fatigue life of mooring and riser components. In particular, Steel Catenary Risers (SCRs) suspended from the floater can be sensitive to VIM-induced fatigue at their mudline touchdown points. Industry currently relies on scaled model testing to determine VIM for design. However, scaled model tests are limited in their ability to represent VIM for the full scale structure since they are generally not able to represent the full scale Reynolds number and also cannot fully represent waves effects, nonlinear mooring system behavior or sheared and unsteady currents. The use of Computational Fluid Dynamics (CFD) to simulate VIM can more realistically represent the full scale Reynolds number, waves effects, mooring system, and ocean currents than scaled physical model tests. This paper describes a set of VIM CFD simulations for a Spar hard tank with appurtenances and their comparison against a high quality scaled model test. The test data showed considerable sensitivity to heading angle relative to the incident flow as well as to reduced velocity. The simulated VIM-induced sway motion was compared against the model test data for different reduced velocities (Vm) and Spar headings. Agreement between CFD and model test VIM-induced sway motion was within 9% over the full range of Vm and headings. Use of the Improved Delayed Detached Eddy Simulation (IDDES, Shur et al 2008) turbulence model gives the best agreement with the model test measurements. Guidelines are provided for meshing and time step/solver setting selection.

A Joint-Industry Effort to Develop and Verify CFD Modeling Practice for Vortex-Induced Motion of a Deep-Draft Semi-Submersible

2021 ◽  
Author(s):  
Hyunchul Jang ◽  
Dae-Hyun Kim ◽  
Madhusuden Agrawal ◽  
Sebastien Loubeyre ◽  
Dongwhan Lee ◽  
...  
Keyword(s):  
Test Data ◽  
Model Test ◽  
Working Group ◽  
Cfd Modeling ◽  
Physical Model Test ◽  
Mooring Lines ◽  
Cfd Models ◽  
Induced Motion ◽  
Modeling Practice ◽  
Decay Tests

Abstract Platform Vortex Induced Motion (VIM) is an important cause of fatigue damage on risers and mooring lines connected to deep-draft semi-submersible floating platforms. The VIM design criteria have been typically obtained from towing tank model testing. Recently, computational fluid dynamics (CFD) analysis has been used to assess the VIM response and to augment the understanding of physical model test results. A joint industry effort has been conducted for developing and verifying a CFD modeling practice for the semi-submersible VIM through a working group of the Reproducible Offshore CFD JIP. The objectives of the working group are to write a CFD modeling practice document based on existing practices validated for model test data, and to verify the written practice by blind calculations with five CFD practitioners acting as verifiers. This paper presents the working group’s verification process, consisting of two stages. In the initial verification stage, the verifiers independently performed free-decay tests for 3-DOF motions (surge, sway, yaw) to check if the mechanical system in the CFD model is the same as in the benchmark test. Additionally, VIM simulations were conducted at two current headings with a reduced velocity within the lock-in range, where large sway motion responses are expected,. In the final verification stage, the verifiers performed a complete set of test cases with small revisions of their CFD models based on the results from the initial verification. The VIM responses from these blind calculations are presented, showing close agreement with the model test data.

scholarly journals Experimental study of hydrodynamic forces acting on ship bow during wave capture

2019 ◽  
pp. 146-152
Author(s):  
Pavel Burakovskiy
Keyword(s):  
Experimental Study ◽  
Test Data ◽  
Model Test ◽  
Hydrodynamic Forces ◽  
Hydrodynamic Loads ◽  
Test Tank ◽  
Head Waves ◽  
Negative Effect

This paper studies behavior of ship in head waves, when her bow dips under water, which leads to hydrodynamic forces and moments to be assessed. This paper presents model test data obtained in the test tank on the model of ship bow (hydrodynamic loads on forecastle deck during wave capture) as well as updates the coefficient of flow around the bow. The study also shows that bulwark has negative effect upon safety in these conditions because it significantly increases hydrodynamic loads on the deck.

Analysis of Turam model test data

1971 ◽  
Vol 9 (2-3) ◽  
pp. 160
Author(s):  
J.P. Williams
Keyword(s):  
Test Data ◽  
Model Test

Measuring the Adhesion of Diamond Thin Films to Substrates Using the Blister Test

1995 ◽  
Vol 383 ◽  
Author(s):  
Jim Sizemore ◽  
R. J. Hohlfelder ◽  
J. J. Vlassak ◽  
W. D. Nix
Keyword(s):  
Thin Films ◽  
Test Data ◽  
Diamond Films ◽  
Cvd Diamond ◽  
Simple Equation ◽  
Testing Technique ◽  
Blister Test ◽  
Plasma Enhanced Cvd ◽  
Si Substrates ◽  
Diamond Thin Films

ABSTRACTIt is shown that the blister testing technique can be used to measure the adhesion of thin films to their substrates. A brief discussion of blister test mechanics is presented here, leading to a simple equation relating adhesion to the height of the blister and the pressure causing it to grow. Blister test data for plasma-enhanced CVD diamond films on Si substrates have been analyzed using this relation. The tests show adhesion energies of 1.8– 2.6 J/m2.

Integral Force/Moment Waterjet Model for CFD Simulations

2010 ◽  
Vol 132 (10) ◽  
Author(s):  
Manivannan Kandasamy ◽  
Seng Keat Ooi ◽  
Pablo Carrica ◽  
Frederick Stern
Keyword(s):  
Experimental Data ◽  
Test Data ◽  
Model Test ◽  
Additional Data ◽  
Inlet Pressure ◽  
Working Fluid ◽  
Local Flow ◽  
Force Moment ◽  
Sinkage And Trim ◽  
Input Variables

An integral force/moment waterjet model for computational fluid dynamics (CFD) is derived for ship local flow/powering predictions, including sinkage and trim. The waterjet induced reaction forces and moment and waterjet/hull interaction stern force replicate the effects of the waterjet without requiring detailed simulations of the waterjet system. The model extends the International Towing Tank Conference (ITTC) waterjet model for sinkage and trim by using an alternative control volume also appropriate for CFD and by including vertical forces and pitching moment in the waterjet/hull force/moment balance. The same grid is used for both without and with waterjet simulations. The CFD waterjet model requires limited waterjet geometry (inlet and outlet areas and locations, and weight of working fluid) and several waterjet flow (mass flow rate, inlet pressure force, inlet and outlet momentum correction factors and flow angles, and stern force and location) input variables. The CFD waterjet model can be used for local flow predictions by using waterjet flow input variables provided by ITTC waterjet model test data, including additional data for waterjet induced inlet pressure and stern forces. It can also be used for powering predictions once waterjet flow input variable correlations are available based on CFD for the waterjet system and/or experimental data. The CFD waterjet model is demonstrated for local flow predictions for the DTMB 5594 high-speed sealift ship model for which ITTC waterjet model test data, including additional data for waterjet induced stern forces, are available. Correlations for the waterjet flow input variables are shown to be feasible using a combination of CFD and experimental data for the waterjet system for three different hulls.

scholarly journals Model Test of a 1:8-Scale Floating Wind Turbine Offshore in the Gulf of Maine1

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Anthony M. Viselli ◽  
Andrew J. Goupee ◽  
Habib J. Dagher
Keyword(s):  
Wind Turbine ◽  
Physical Model ◽  
Test Data ◽  
Model Test ◽  
Test Site ◽  
Full Scale ◽  
Scale Construction ◽  
Offshore Wind ◽  
Testing Effort ◽  
Floating Wind Turbine

A new floating wind turbine platform design called VolturnUS developed by the University of Maine uses innovations in materials, construction, and deployment technologies such as a concrete semisubmersible hull and a composite tower to reduce the costs of offshore wind. These novel characteristics require research and development prior to full-scale construction. This paper presents a unique offshore model testing effort aimed at derisking full-scale commercial projects by providing scaled global motion data, allowing for testing of materials representative of the full-scale system, and demonstrating full-scale construction and deployment methods. A 1:8-scale model of a 6 MW semisubmersible floating wind turbine was deployed offshore Castine, ME, in June 2013. The model includes a fully operational commercial 20 kW wind turbine and was the first grid-connected offshore wind turbine in the U.S. The testing effort includes careful selection of the offshore test site, the commercial wind turbine that produces the correct aerodynamic thrust given the wind conditions at the test site, scaling methods, model design, and construction. A suitable test site was identified that produced scaled design load cases (DLCs) prescribed by the American Bureau of Shipping (ABS) Guide for Building and Classing Floating Offshore Wind Turbines. A turbine with a small rotor diameter was selected because it produces the correct thrust load given the wind conditions at the test site. Some representative data from the test are provided in this paper. Model test data are compared directly to full-scale design predictions made using coupled aeroelastic/hydrodynamic software. Scaled VolturnUS performance data during DLCs show excellent agreement with full-scale predictive models. Model test data are also compared directly without scaling against a numerical representation of the 1:8-scale physical model for the purposes of numerical code validation. The numerical model results compare favorably with data collected from the physical model.

Sign in / Sign up

Export Citation Format

Share Document