Investigating the Effect of Adding Nano Materials and Carbon Fiber to Impact Strength of Cementitious Composite

2021 ◽  
pp. 154-171
Author(s):  
Zainab H. Mahdi
Keyword(s):  
Carbon Fiber ◽  
Impact Strength ◽  
Nano Materials ◽  
Cementitious Composite

Hybrid effects of carbon fiber and nanoclay as fillers on the performances of recycled wood-plastic composites

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 7671-7686
Author(s):  
Young-Rok Seo ◽  
Sang-U Bae ◽  
Birm-June Kim ◽  
Min Lee ◽  
Qinglin Wu
Keyword(s):  
Carbon Fiber ◽  
Impact Strength ◽  
Carbon Fibers ◽  
Synergistic Effects ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Raw Material ◽  
Scanning Electron Micrographs ◽  
Plastic Composite ◽  
The Impact

Waste wood-plastic composite (WPC) was used in this work as a raw material to produce recycled WPCs reinforced with carbon fiber and nanoclay. To evaluate the synergistic effects of carbon fiber and nanoclay, various performances (i.e., microstrucural, mechanical, thermal, water absorption, and electrical properties) were investigated. Scanning electron micrographs and X-ray diffraction analysis of the fillers (carbon fiber and nanoclay) present in the recycled WPCs showed that the nanoclays were properly intercalated when filled with carbon fibers. According to mechanical property analysis, hybrid incorporation of carbon fibers and nanoclays improved impact strength, tensile strength, and flexural strength. However, further incorporation of nanoclays reduced the impact strength and did not improve the tensile modulus or the flexural modulus. The carbon fibers present in the recycled WPCs improved the electrical conductivity of the composites, despite the various fillers that interfered with their electrical conduction. In addition, carbon fibers and nanoclays were mixed into the recycled WPCs to improve the thermal stability of the composites. Finally, the presence of nanoclays in recycled WPCs led to increased water uptake of the composites.

scholarly journals The effect of rubber on the mechanical properties of epoxy and carbon fiber (Review)

2020 ◽  
Vol 1 (312) ◽  
pp. 11-21
Author(s):  
M. N. Meiirbekov ◽  
◽  
M. B. Ismailov ◽  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Carbon Fiber ◽  
Impact Strength ◽  
Yield Strength ◽  
Strength Properties ◽  
Carboxyl Groups ◽  
Published Data ◽  
Hydroxyl Groups

The paper presents published data on the effect of rubber elastomers on the strength properties of epoxy resin (ES) and carbon fiber. The introduction of 10% rubbers into ES ED-20 leads to an increase in compressive strength by 50%, tensile strength by 51%, impact strength by 133% and elongation by 128%. The optimal content of rubber with carboxyl groups for the OLDEN mixture was 10-12.5%, while the increase in compressive strength was 48%, impact strength - 73% and elongation - 187%. For DER 331 resin, the study was conducted with two hardeners Piperidine and DETA. The best results for Piperidine hardener were obtained on rubber with hydroxyl groups, with its optimal content of 2.5%, impact strength increased by 170%. For the hardener DETA, the best results were obtained on rubber with carboxyl groups at its optimal content of 10%, the increase in impact strength was 66%. When modifying carbon fiber with rubbers, it leads to a significant increase in the yield strength in tension by 42%, the modulus of elasticity in bending by 63%, and with a slight loss of impact strength.

scholarly journals Curing Kinetics, Mechanical Properties and Thermomechanical Analysis of Carbon Fiber/epoxy Resin Laminates with Different Ply Orientations

2021 ◽  
Author(s):  
Chenglin Zhang ◽  
Guohua Gu ◽  
Shuhua Dong ◽  
Zhitao Lin ◽  
Chuncheng Wei ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Impact Strength ◽  
Epoxy Resin ◽  
Composite Laminates ◽  
Bending Strength ◽  
Fiber Composite ◽  
Curing Process ◽  
Scanning Calorimetry ◽  
The Impact ◽  
Carbon Fiber Epoxy

Abstract In this study, the nonisothermal differential scanning calorimetry (DSC) was carried out to evaluate the curing reaction of fiber/epoxy laminates. The optimal curing process of the prepreg was obtained by T-β extrapolation method and nth-order reaction curing kinetic equation. The bending strength, impact strength and thermodynamic properties of the composite laminates with different ply orientations were investigated, respectively. The results show that the apparent activation energy and the reaction order of the prepregs are 82.89 kJ/mol and 0.92, respectively. The curing process of carbon fiber/epoxy resin prepreg is 130 ℃ /60min + 160 ℃/30 min. The bending strength of [0]10 laminate is 1948.3 MPa, which is 11.8 times higher than that of [+ 45/-45]5s laminate, and 96.4% higher than that of [0/90]5s laminate. The impact strength of [0]10 laminate is higher than that of [+ 45/-45]5s and [0/90]5s laminates. The glass transition temperature (Tg) of the laminates is 142 ~ 146 ℃, and the loss factor of [0]10 laminate is significantly higher than that of [+ 45/-45]5s and [0/90]5s laminates. This research provides a theoretical basis for the further application of prepregs to fiber composite materials.

Improvement of Mechanical Properties of Polyphenylene Sulfide/Carbon Fiber Composites Modified by Aminated Reinforcement

2015 ◽  
Vol 815 ◽  
pp. 523-528 ◽  
Author(s):  
Rui Hong ◽  
Kun Zhang ◽  
Bao Ying Liu ◽  
Gang Zhang ◽  
Xiao Jun Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Carbon Fiber ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Melting Process ◽  
Fiber Composites ◽  
Polyphenylene Sulfide ◽  
Carbon Fiber Composites ◽  
Mass Fractions

The carbon fiber (CF) reinforced polyphenylene sulfide (PPS) composite was modified by aminated polyphenylene sulfide (PPS-NH2) with different mass fractions. The quantified influence of aminated PPS on PPS/CF composites was investigated. The PPS/CF composite with 7wt% PPS-NH2 showed the best mechanical properties. The tensile strength, flexural strength, flexural modulus and impact strength of the composites increased by 12.5%, 13.0%, 38.5% and 31.5%, respectively. PPS-NH2 hardly influenced the melting process of PPS/CF composite. But the crystallization temperature (Tc) of PPS were obviously increased with the present of aminated PPS.

The Influence of GI and GII on the compression after impact strength of carbon fiber/epoxy laminates

2017 ◽  
Vol 52 (8) ◽  
pp. 991-1003 ◽  
Author(s):  
Alan Tate Nettles ◽  
Luke Scharber
Keyword(s):  
Carbon Fiber ◽  
Impact Strength ◽  
Compression Strength ◽  
Epoxy Resins ◽  
Impact Damage ◽  
Compression After Impact ◽  
The Difference ◽  
Type Of Failure ◽  
Carbon Fiber Epoxy ◽  
Residual Compression

This study measured the compression after impact strength of IM7 carbon fiber laminates made from epoxy resins with various mode I and mode II toughness values to observe the effects of these toughness values on the resistance to damage formation and subsequent residual compression strength-carrying capabilities. A total of seven different epoxy resin systems were used ranging in approximate GI values of 245–665 J/m2 and approximate GII values of 840–2275 J/m2. The results for resistance to impact damage formation showed that there was a direct correlation between GII and the planar size of damage as measured by thermography. Subsequent residual compression strength testing suggested that GI had no influence on the measured values and most of the difference in compression strength was directly related to the size of damage. Thus, delamination growth assumed as an opening type of failure mechanism does not appear to be responsible for the loss of compression strength.

scholarly journals Hybrid Effect of Wollastonite Fiber and Carbon Fiber on the Mechanical Properties of Oil Well Cement Pastes

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Jianglin Zhu ◽  
Jiangxiong Wei ◽  
Qijun Yu ◽  
Mingbiao Xu ◽  
Yuwei Luo
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Carbon Fiber ◽  
Impact Strength ◽  
Flexural Strength ◽  
Cement Stone ◽  
Oil Well ◽  
Cement Slurry ◽  
Oil Well Cement ◽  
Well Cement

Oil well cement is a type of natural brittle material that cannot be used directly in cementing operations. Fiber is a type of material that can effectively improve the strength and toughness of cement stone, and hybrid fiber materials can more effectively improve the performance of a cement sample. To overcome the natural defects of oil well cement, the new mineral fiber, i.e., wollastonite fiber, and common carbon fiber were used in oil well cement, and the micromorphology, mechanical properties, and stress-strain behavior of the cement were evaluated. The experimental results show that carbon fiber and wollastonite fiber are randomly distributed in the cement paste. The mechanical properties of the cement paste are improved by bridging and pulling out. The compressive strength, flexural strength, and impact strength of cement stone containing only carbon fiber or wollastonite fiber are higher than those of the pure cement, but too many fibers are not conducive to the development of mechanical properties. A mixture of 0.3% carbon fiber with 6% wollastonite fiber in oil well cement slurry results in a greater increase in compressive strength, flexural strength, and impact strength. In addition, compared with blank cement stone, the strain of the mixed cement stone increases substantially, and the elastic modulus decreases by 37.8%. The experimental results supply technical support for the design of a high-performance cement slurry system.

Sign in / Sign up

Export Citation Format

Share Document