scholarly journals Effects of Calcination Temperatures on The Catalytic Activities of Alumina Supported Cobalt and Chromium Catalysts

2019 ◽  
Vol 14 (3) ◽  
pp. 654
Author(s):  
Mardwita Mardwita ◽  
Eka Sri Yusmartini ◽  
Nidya Wisudawati
Keyword(s):  
Metal Particle ◽  
Strong Support ◽  
High Dispersion ◽  
Impregnation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Catalytic Activities ◽  
Calcination Temperatures ◽  
Transmission Electron ◽  
Different Temperatures

Catalysts properties are important for catalytic reactions. The interaction between support and metal in a catalyst is resulted from catalyst preparation. In this study, gamma-alumina (Al2O3) supported cobalt (Co) and chromium (Cr) catalysts were prepared by impregnation method and calcined at two different temperatures, they are 400 °C for 4 hours and 800 °C for 4 hours. The resulted catalysts contained 10 wt.% of metal and denoted as Co/Al2O3(400), Co/Al2O33(800), Cr/Al2O3(400), and Cr/Al2O3(800) catalysts. The surface and state of the catalysts were examined by using x-ray diffraction (XRD), x-ray photoelectron spectrometer (XPS) and transmission electron microscopy (TEM). The XRD result reveals that strong interaction between Co and Al2O3 due to a formation of higher cobalt oxide. The XRD result further indicates aggregation and strong support metal interaction between Co and Al2O3 during calcination. On the other hand, TEM result showed that large Co particle was observed on Al2O3. The Cr/Al2O3 catalysts were characterized by using XPS. The XPS results showed that Cr/Al2O3(800) catalyst was dominated by Cr6+ species at binding energy 579.04 eV, indicating high dispersion of Cr on Al2O3. Moreover, Cr metal particle was not observed on XRD and TEM image. All the characterization results provide information that the impregnated metal on Al2O3 showed different properties. Co metal particle tends to be more oxidized and formed large particle, however it was not observed on Cr metal particle. Copyright © 2019 BCREC Group. All rights reserved 

scholarly journals Solvent-Tuned Synthesis of Mesoporous Nickel Cobaltite Nanostructures and Their Catalytic Properties

2019 ◽  
Vol 9 (6) ◽  
pp. 1100 ◽  
Author(s):  
Xiangfeng Guan ◽  
Peihui Luo ◽  
Yunlong Yu ◽  
Xiaoyan Li ◽  
Dagui Chen
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Catalytic Activities ◽  
Transmission Electron ◽  
Nickel Cobaltite ◽  
Solvent Type ◽  
Bet Method ◽  
Mesoporous Nico2o4

In this paper, we prepared mesoporous nickel cobaltite (NiCo2O4) nanostructures with multi-morphologies by simple solvothermal and subsequent heat treatment. By adjusting the solvent type, mesoporous NiCo2O4 nanoparticles, nanorods, nanowires, and microspheres were easily prepared. The as-prepared products were systematically characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and Brunauer–Emmett–Teller (BET) method. Furthermore, the catalytic activities towards the thermal decomposition of ammonium perchlorate (AP) of as-prepared NiCo2O4 nanostructures were investigated.

Fe–Cr/Al2O3 metal-ceramic composites: Nature and size of the metal particles formed during hydrogen reduction

1994 ◽  
Vol 9 (1) ◽  
pp. 229-235 ◽  
Author(s):  
Ch. Laurent ◽  
J.J. Demai ◽  
A. Rousset ◽  
K.R. Kannan ◽  
C.N.R. Rao
Keyword(s):  
Hydrogen Reduction ◽  
Ceramic Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Total Reduction ◽  
Transmission Electron ◽  
Combined Use ◽  
Metal Ceramic ◽  
Different Temperatures ◽  
Metallic Species

Fe-Cr/Al2O3 metal-ceramic composites prepared by hydrogen reduction at different temperatures and for different periods have been investigated by a combined use of Mössbauer spectroscopy, x-ray diffraction, transmission electron microscopy, and energy-dispersive x-ray spectroscopy in order to obtain information on the nature of the metallic species formed. Total reduction of Fe3+ does not occur by increasing the reduction time at 1320 K from 1 to 30 h, and the amount of superparamagnetic metallic species is essentially constant (about 10%). Temperatures higher than 1470 K are needed to achieve nearly total reduction of substitutional Fe3+. Interestingly, iron favors the reduction of chromium. The composition of the Fe-Cr particles is strongly dependent on their size, the Cr content being higher in particles smaller than 10 nm.

Preparation and Property of Al87Ce3Ni8.5Mn1.5 Nanophase Amorphous Composites

2011 ◽  
Vol 412 ◽  
pp. 263-266
Author(s):  
Hong Wei Zhang ◽  
Li Li Zhang ◽  
Feng Rui Zhai ◽  
Jia Jin Tian ◽  
Can Bang Zhang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Single Phase ◽  
Volume Fraction ◽  
Material Structure ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Different Temperatures

The higher mechanical strength of Al87Ce3Ni8.5Mn1.5 nanophase amorphous composites has been obtained with two methods. The first nanophase amorphous composites are directly produced by the single roller spin quenching technology. The method taken for the second nanophase amorphous composites is at first to obtain amorphous single-phase alloy, followed by annealed at different temperatures .The formative condition, the microstructure, the particle size, the volume fraction of α-Al phase and microhardness of nanophase amorphous composites etc have been investigated and compared by X-ray diffraction (XRD) and transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The microstructure of composites produced by the second method is higher than the former, the fabricated material structure of the system is more uniform and the process is easier to control.

Effect of Calcination Temperature on the Morphological and Phase Structure of Hydrothermally Synthesized Copper Ion Doped TiO2 Nanotubes

2014 ◽  
Vol 1024 ◽  
pp. 7-10 ◽  
Author(s):  
Mohd Hasmizam Razali ◽  
M.N. Ahmad-Fauzi ◽  
Abdul Rahman Mohamed ◽  
Srimala Sreekantan
Keyword(s):  
Calcination Temperature ◽  
Morphological Evolution ◽  
Copper Ion ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Different Temperatures ◽  
Scanning Electronmicroscopy ◽  
Higher Temperature ◽  
Uniform Diameter

Morphological evolution and phase transformations of copper ion doped TiO2nanotubes after being calcined at different temperatures were studied by field emission scanning electronmicroscopy, transmission electron microscopy, and X-ray diffraction. After calcination at 300°C, the nanotubes with uniform diameter and length wereobtained. At 400°C, the nanotube structures were maintained. Nevertheless the inner tube diameter became narrower, and in same instances disappeared due to aggregation of nanotubes. The copper ion doped TiO2nanotubes then transformed to nanorodsat 500°C and the length of the nanorodsshortens after calcination at 600 °C. When the calcination temperature was further increased to 700°C, the nanorodsdisintegrate to form nanoparticles. On the other hand the phase structures of copper ion doped TiO2nanotubes calcined at 300 and 400 °C were TiO2hexagonal. After calcined at higher temperature (600 and 700°C) they transformed to anatase TiO2(tetragonal).

A new high-temperature inorganic–organic proton conductor: lanthanum sulfophenyl phosphate

2016 ◽  
Vol 70 (3) ◽  
Author(s):  
Ming-Feng Song ◽  
Zhong-Fang Li ◽  
Guo-Hong Liu ◽  
Su-Wen Wang ◽  
Xiao-Yan Yin ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Layered Structure ◽  
Proton Conductor ◽  
X Ray Diffraction ◽  
X Ray ◽  
Good Thermal Stability ◽  
Transmission Electron ◽  
Good Crystallinity ◽  
Different Temperatures ◽  
Thermal Stability Of

AbstractLanthanum sulfophenyl phosphate (LaSPP) was synthesized by m-sulfophenyl phosphonic acid and lanthanum nitrate. UV-Vis spectrophotometry and Fourier-transform infrared spectroscopy indicate that the desired product was obtained and its elementary composition and typical layered structure were determined by energy dispersive X-ray spectroscopy and scanning electron microscopy. Transmission electron microscopy (TEM) proved its typical layered structure and X-ray diffraction spectroscopy indicated its good crystallinity and the interlayer distance of about 15.67 Å , which matches the value obtained by TEM (2.0 nm). Thermogravimetry and differential thermal analysis revealed good thermal stability of LaSPP. Proton conductivity of LaSPP was measured at different temperatures and relative humidities (RH), reaching values of 0.123 S cm

scholarly journals Luminescence properties of Eu3+ activated Y2MoO6 powders calcined at different temperatures

2020 ◽  
Vol 14 (1) ◽  
pp. 71-76 ◽  
Author(s):  
Nadezda Stankovic ◽  
Marko Nikolic ◽  
Branislav Jelenkovic ◽  
Nina Daneu ◽  
Jelena Maletaskic ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
X Ray Diffraction ◽  
Light Emitting ◽  
White Leds ◽  
Calcination Temperatures ◽  
Transmission Electron ◽  
Light Region ◽  
Lower Treatment ◽  
Different Temperatures ◽  
White Light Emitting Diodes

In the last decade, an immense progress has been made in white LEDs, mainly due to the development of red-emitting phosphors. In this paper, we report on the synthesis of Eu3+ activated Y2MoO6 by a self-initiated and self-sustained method. The obtained powder was calcined at various temperatures in the 600-1400?C range and examined by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and photoluminescence spectroscopy (PL). The results revealed that all powders are single phase Y2MoO6:Eu3+, with particle size in the nanorange at lower treatment temperatures (600 and 800?C) and in the microrange at higher calcination temperatures (1000-1400?C). The obtained powders are promising materials for white light-emitting diodes as they can efficiently absorb energy in 324-425 nm region (near-UV to blue light region) and emit at 611 nm in the red region of the spectrum, while exhibiting high thermal and chemical stability.

scholarly journals Preparation and characterization of cobalt and copper oxide nanocrystals

2019 ◽  
Vol 37 (3) ◽  
pp. 347-352
Author(s):  
A. H. Moharram
Keyword(s):  
Microwave Irradiation ◽  
Copper Oxide ◽  
Chemical Precipitation ◽  
High Dispersion ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Direct Band ◽  
Cuo Nanocrystals

AbstractCopper oxide and cobalt oxide (Co3O4, CuO) nanocrystals (NCs) have been successfully prepared using microwave irradiation. The obtained powders of the nanocrystals (NCs) were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric (TGA) analysis and Fourier-transform infrared spectroscopy. The obtained results confirm the presence of both nanooxides which have been produced during chemical precipitation using microwave irradiation. TEM micrographs have shown that the obtained nanocrystals are characterized by high dispersion and narrow size distribution. The results of X-ray diffraction confirmed those obtained from the transmission electron microscope. Optical absorption analysis indicated the direct band gap for both kinds of the nanocrystals.

scholarly journals S tudies on the phase transitions and properties of tungsten (VI) oxide nanoparticles by X - Ray diffraction (XRD) and thermal analysis

2017 ◽  
Vol 26 (1) ◽  
Author(s):  
S.F. Abdullah ◽  
S. Radiman ◽  
M.A. Abdul Hamid ◽  
N.B. Ibrahim
Keyword(s):  
Thermal Analysis ◽  
Phase Transitions ◽  
Photoelectron Spectroscopy ◽  
Average Diameter ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Calcination Temperatures ◽  
Transmission Electron ◽  
Scherrer Formula

Tungsten (VI) oxide, WO3nanoparticles were synthesized by colloidal gas aphrons(CGAs) technique.The resultant WO3nanoparticleswere characterized by thermogravimetric-differential thermal analysis (TG-DTA) and X-Ray diffraction (XRD) measurements in order to determine the phase transitions, the crystallinity and the size of theWO3nanoparticles. As a comparison, transmission electron microscope (TEM) was used to investigate the size of the WO3nanoparticles. The result from XRD and DTA show that the formation of polymorphsWO3nanoparticles have the following sequence: orthorhombic (b-WO3)®monoclinic (g-WO3) ®triclinic (d-WO3) ®monoclinic (e-WO3) with respect to the calcination temperature of 400, 500, 600 and 700°C. No diffraction peaks were found in the X-Ray diffraction measurements for the sample heat treated at 300°C (as-prepared), suggesting that an amorphous structure was obtained at this temperature whereas the crystallinity had been obtained by the other samples of theWO3nanoparticles at the calcination temperatures of 400, 500, 600 and 700°C. It is also found that the X-Ray diffraction measurements produced an average diameter of (30 ±5), (50 ±5), (150 ±10) and (200 ±10) nm at calcination temperatures of 400, 500, 600 and 700°C respectively by using Debye-Scherrer formula. The TG curve revealed that the WO3nanoparticles is purely anhydrous since the weight loss is insignificant (0.3 –1.4) % from 30 until 600°C for the WO3nanoparticles calcined at 400°C. Finally, the composition and the purity of the WO3nanoparticleshave been examined by X-Ray photoelectron spectroscopy (XPS). Theresults indicate no significant changes to the composition and the purity of the WO3nanoparticle produced due to the temperature variations 

scholarly journals Synthesis of porous LaFeO3 prepared by nanocasting method for photo-Fenton degradation of oily-containing wastewater

2021 ◽  
Vol 11 (1) ◽  
pp. xx-xx
Author(s):  
Nga Phan To ◽  
Lien Nguyen Hong ◽  
Tuyen Le Van ◽  
Nhan Phan Chi ◽  
Huyen Phan Thanh
Keyword(s):  
Electron Microscopy ◽  
Catalytic Activity ◽  
Visible Light ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Catalytic Activities ◽  
Transmission Electron ◽  
Visible Light Driven ◽  
Adsorption Desorption

Porous LaFeO3 were synthesised by nanocasting method using mesoporous silica (SBA-15) as a hard template and used as a visible-light-driven photocatalyst. The as-synthesised LaFeO3 photocatalyst were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray Diffraction (XRD), N2 adsorption-desorption, and Ultraviolet–Visible Diffuse Reflectance Spectroscopy (UV-vis DRS). The photo-Fenton catalytic activities of porous LaFeO3 were investigated for the degradation of oily-containing wastewater. The results showed that porous LaFeO3 had better photo-Fenton catalytic activity under visilbe light irradiation than pure LaFeO3. The remarkable improvement photo-Fenton catalytic activity of porous LaFeO3 material could be attributed to the synergistic effect of adsorption and visible light photo-Fenton processes thanks to its porous structure.

scholarly journals Biochar-Supported FeS/Fe3O4 Composite for Catalyzed Fenton-Type Degradation of Ciprofloxacin

Catalysts ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1062 ◽  
Author(s):  
Yue Wang ◽  
Xiaoxiao Zhu ◽  
Dongqing Feng ◽  
Anthony K. Hodge ◽  
Liujiang Hu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Iron Sulfide ◽  
Magnetic Composite ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Magnetite Fe3o4 ◽  
Different Temperatures ◽  
Cost Efficient

The Fenton-type oxidation catalyzed by iron minerals is a cost-efficient and environment-friendly technology for the degradation of organic pollutants in water, but their catalytic activity needs to be enhanced. In this work, a novel biochar-supported composite containing both iron sulfide and iron oxide was prepared, and used for catalytic degradation of the antibiotic ciprofloxacin through Fenton-type reactions. Dispersion of FeS/Fe3O4 nanoparticles was observed with scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS) and transmission electron microscopy (TEM). Formation of ferrous sulfide (FeS) and magnetite (Fe3O4) in the composite was validated by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Ciprofloxacin (initial concentration = 20 mg/L) was completely degraded within 45 min in the system catalyzed by this biochar-supported magnetic composite at a dosage of 1.0 g/L. Hydroxyl radicals (·OH) were proved to be the major reactive species contributing to the degradation reaction. The biochar increased the production of ·OH, but decreased the consumption of H2O2, and helped transform Fe3+ into Fe2+, according to the comparison studies using the unsupported FeS/Fe3O4 as the catalyst. All the three biochars prepared by pyrolysis at different temperatures (400, 500 and 600 °C) were capable for enhancing the reactivity of the iron compound catalyst.

Sign in / Sign up

Export Citation Format

Share Document