Ti/TiO2/SiO2 multilayer thin films with enhanced spectral selectivity for optical narrow bandpass filters

Thin film-based optical sensors have been attracting increasing interest for use in developing technologies such as biometrics. Multilayered dielectric thin films with different refractive indices have been utilized to modulate the optical properties in specific wavelength bands for spectral selectivity of Thin Film Narrow Bandpass Filters (TFNBFs). Progress in TFNBF design has been made with the incorporation of metallic thin films. Narrower bandwidths with higher transmittance have been achieved in specific spectral bands. In this work, Ti/TiO2/SiO2 based multilayer thin films were prepared using pulsed-DC reactive sputtering. Computer simulations using the Essential Macleod Program allowed the optimal number of layers and thickness of the multilayer thin films to be determined to efficiently tailor the optical path transmitting specific wavelength bands. The addition of Ti metal layers within dielectric (TiO2/SiO2) multilayer thin films significantly changes the cutoff frequency of transmittance at specific wavelengths. Representative 26 multilayer films consisting of Ti, TiO2, and SiO2 show lower transmittance of 10.29% at 400 nm and 10.48% at 680 nm. High transmittance of 80.42% at 485 nm was observed, which is expected to improve the spectral selectivity of the TFNBF. This work provides a contribution to future simulation based design strategy based on experimental thin film engineering for potential industrial development opportunities such as optical biometrics.

Microstructural and Optical Properties of MgAl2O4 Spinel: Effects of Mechanical Activation, Y2O3 and Graphene Additions

Magnesium aluminate and other alumina-based spinels attract attention due to their high hardness, high mechanical strength, and low dielectric constant. MgAl2O4 was produced by a solid-state reaction between MgO and α-Al2O3 powders. Mechanical activation for 30 min in a planetary ball mill was used to increase the reactivity of powders. Yttrium oxide and graphene were added to prevent abnormal grain growth during sintering. Samples were sintered by hot pressing under vacuum at 1450 °C. Phase composition and microstructure of sintered specimens were characterized by X-ray powder diffraction and scanning electron microscopy. Rietveld analysis revealed 100% pure spinel phase in all sintered specimens, and a decrease in crystallite size with the addition of yttria or graphene. Density measurements indicated that the mechanically activated specimen reached 99.6% relative density. Furthermore, the highest solar absorbance and highest spectral selectivity as a function of temperature were detected for the mechanically activated specimen with graphene addition. Mechanical activation is an efficient method to improve densification of MgAl2O4 prepared from mixed oxide powders, while additives improve microstructure and optical properties.

Structure, Optical Properties and Thermal Stability of All-Ceramic Solar Selective Absorbing Coatings: A Mini Review

Solar selective absorbing coatings (SSAC) harvest solar energy in the form of thermal energy. Traditional metal-rich SSACs like cermet-based coatings and semiconductor–metal tandems usually exhibit both a high solar absorptance and a low thermal emittance; however, metal nanoparticles can easily oxidize or diffuse at high temperature. Different from these SSACs, the all-ceramic SSACs can keep the superior optical performance at high temperatures by restraining oxidation and metal element diffusion. Besides, the facile and inexpensive fabrication of the all-ceramic SSACs makes it possible for commercial applications. These SSACs are usually a regular combination of transition-metal carbides and nitrides, which show great thermal stability and optical properties simultaneously. The structure design of the SSACs will affect the element diffusion, element oxidation, phase transition, as well as the spectral selectivity obviously. In this article, we review the structure designs of all-ceramic SSACs, and the optical properties and thermal stability of the all-ceramic SSACs in the latest literature are also compared. The purpose of this review is to identify the optimal structure design of the all-ceramic SSAC, and we also present an outlook for the structure design strategy for all-ceramic SSACs with high photothermal conversion efficiency and thermal stability.

Ti/TiO2/SiO2 Multilayer Thin Films With Enhanced Spectral Selectivity For Optical Applications

Thin film-based optical sensors have been attracting increasing interest for use in developing technologies such as biometrics. Multilayered dielectric thin films with different refractive indices have been utilized to modulate the optical properties in specific wavelength bands for spectral selectivity of Thin Film Narrow Bandpass Filters (TFNBFs). Progress in TFNBF design has been made with the incorporation of metallic thin films. Narrower bandwidths with higher transmittance have been achieved in specific spectral bands. In this work, Ti/TiO2/SiO2 based multilayer thin films were prepared using pulsed-DC reactive sputtering. Computer simulations using the Essential Macleod Program allowed the optimal number of layers and thickness of the multilayer thin films to be determined to efficiently tailor the optical path transmitting specific wavelength bands. The addition of Ti metal layers within dielectric (TiO2/SiO2) multilayer thin films significantly changes the cutoff frequency of transmittance at specific wavelengths. Representative 26 multilayer films consisting of Ti, TiO2, and SiO2 show lower transmittance of 10.29 % at 400 nm and 10.48 % at 680 nm. High transmittance of 80.42 % at 485 nm was observed, which is expected to improve the spectral selectivity of the TFNBF. This work provides a contribution to future simulation based design strategy based on experimental thin film engineering for potential industrial development opportunities such as optical biometrics.

Metabolite-Specific Echo-Planar Imaging of Hyperpolarized [1-13C]Pyruvate at 4.7 T

Although hyperpolarization (HP) greatly increases the sensitivity of 13C MR, the usefulness of HP in vivo is limited by the short lifetime of HP agents. To address this limitation, we developed an echo-planar (EPI) sequence with spectral-spatial radiofrequency (SSRF) pulses for fast and efficient metabolite-specific imaging of HP [1-13C]pyruvate and [1-13C]lactate at 4.7 T. The spatial and spectral selectivity of each SSRF pulse was verified using simulations and phantom testing. EPI and CSI imaging of the rat abdomen were compared in the same rat after injecting HP [1-13C]pyruvate. A procedure was also developed to automatically set the SSRF excitation pulse frequencies based on real-time scanner feedback. The most significant results of this study are the demonstration that a greater spatial and temporal resolution is attainable by metabolite-specific EPI as compared with CSI, and the enhanced lifetime of the HP signal in EPI, which is attributable to the independent flip angle control between metabolites. Real-time center frequency adjustment was also highly effective for minimizing off-resonance effects. To the best of our knowledge, this is the first demonstration of metabolite-specific HP 13C EPI at 4.7 T. In conclusion, metabolite-specific EPI using SSRF pulses is an effective way to image HP [1-13C]pyruvate and [1-13C]lactate at 4.7 T.

Simple PDMS/AIN emitter as a passive daytime radiative cooling design

Radiative cooling is a passive cooling purpose where a surface naturally cools by radiating the mid-infrared heat radiation to the cold outer space through the atmospheric window . Daytime passive radiative cooling technologies can be simply provided by using a multi-layer design that emits strongly in the transparency atmospheric window, while presents high reflectance in the solar spectrum . In this study, we propose a polydimethylsiloxane foil ) coated aluminum nitride (AIN) deposed onto silver (Ag) coated glass as a radiative cooler for enhancing both daytime and nighttime radiative cooling performances. The spectral selectivity of the proposed device was obtained using matrix method. Numerical results show that our proposed design can reflect more than 96 % in the solar spectrum, while its average emissivity in the atmospheric window can reach more than 90 %.In the absence of wind speed, the proposed device can achieve a net cooling power of under direct sunlight, cooling to a below the ambient air temperature. At nighttime, the proposed device temperature can drop by below the ambient, leading to a net cooling power of . Therefore, the proposed radiative design can fundamentally enable new methods for exploiting solar energy harvesting and energy conservation.

2D MXenes: the lowest-emissivity black materials

Black materials with low infrared absorption/emission are rare in nature but highly desired in numerous areas, such as solar-thermal energy harvesting, infrared camouflage, and anti-counterfeiting. Due to the lack of spectral selectivity in intrinsic materials, such counter-intuitive properties are generally realized by constructing complicated subwavelength artificial nanostructures with precise nanofabrication techniques. Here, we report that 2D Ti3C2Tx MXenes embrace both a low emissivity (down to 10%) and a high solar absorptance (up to 90%), yielding the best spectral selectivity (8.2) and the highest solar-thermal efficiency among the reported intrinsic solar absorbing materials. We demonstrate their appealing potentials in the aforementioned areas. Moreover, the spectral selectivity relies on both the nanoflake orientations and terminal groups, providing great tunability. First-principles calculations suggest more potential low-emissivity MXenes such as Ti2CTx, Nb2CTx, and V2CTx. This work opens the avenue to further exploration of a family of low-emissivity black materials with over 70 members.