Numerical Analysis of Slope Stability Considering Grading and Seepage Prevention

The normal operation of Yulangpei tailings reservoir is affected by landslide stability. In this paper, taking the main and side slopes near the dam bank of the Yulangpei ditch as an example, water-soil coupling theory is applied to comprehensively evaluate the reliability of the side slopes of the tailings reservoir. Grading and seepage prevention (GSP) measures and the suction of the substrate are considered, as well as the infiltration of different rainfall and reservoir water levels. We numerically simulate the typical three forms of side slopes under the coupling conditions and conduct a reliable and comprehensive evaluation of tailings reservoir side slopes. The study shows that under six reservoir water level changes, the factor of safety (FS) of the bank slope shows a hysteresis effect. According to nine rainfall infiltration conditions and during rainfall, the greater the rainfall intensity, the greater the weakening effect. When rainfall stops, the FS rebounds. After GSP measures, the initial stability of the bank slope under different conditions is improved, but the main slope is more sensitive to changes in rainfall and water levels.

Comparison of Initial Stability of Oblong, Large Circular, and Multiple-Plug “Snowman” Osteochondral Autografts for Elongated Focal Cartilage Lesions: A Biomechanical Study in a Porcine Model

Background: Distal femoral osteochondral allograft transplantation (OAT) is an effective treatment of osteochondral lesions in the knee measuring >2 cm2 in select patients. Prior studies have demonstrated that the morphology of the plug can affect graft-host interference fit. To our knowledge, there are no data comparing the initial biomechanical stability of standard cylindrical plugs with multiple-plug and oblong-plug morphologies. Hypothesis: Large cylindrical single-plug (LCSP) and oblong single-plug (OSP) grafts will have greater pull-out strength, and therefore greater initial stability, than multiple-plug (MP) grafts in a cadaveric porcine femur model. Study Design: Controlled laboratory study. Methods: A total of 55 porcine distal femurs were divided into 3 groups—LCSP (n = 18), OSP (n = 19), and MP (n = 18)—according to the plug morphology used. The method of graft harvesting and implantation was based on technique guides for the respective implant systems. The sizes (length × width × depth) of the osteochondral defects created in each of the groups were approximately 20.2 × 20.2 × 9.4–mm for the LCSP group, 14.4 × 30.5 × 7.9–mm for the OSP group, and 14.8 × 14.8 × 9.9–mm for the MP group. Tensile testing was performed on each graft to determine pull-out strength. Results: The pull-out strength was significantly lower in the OSP group (65.7 N) versus the LCSP (133 N; P = .0005) and the MP (117.6 N; P = .001) groups. There was no statistically significant difference in pull-out strength between the LCSP and MP groups ( P = .42). There were no statistically significant differences in displacement at maximum load among any 2 of the 3 groups. Conclusion: These findings suggest that while initial stability may play a role in the clinical outcomes of osteochondral allograft (OCA) implantation, the biological milieu in vivo for each graft setting perhaps has a greater impact on the success of an OAT procedure. Further study is needed on the relationship between OCA biomechanics and clinical outcomes of OAT.

Can the design of the instruments used for undersized osteotomies influence the initial stability of implants installed in low-density bone? An in vitro pilot study

Objectives The aims of this study were to compare the initial implant stability obtained using four different osteotomy techniques in low-density synthetic bone, to evaluate the instrument design in comparison to the implant design, and to determinate a possible correlation between the insertion torque and initial stability quotient (ISQ). Materials and methods Four groups were identified in accordance with the osteotomy technique used (n = 10 implants per group): group G1, osteotomy using the recommended drilling sequence; group G2, osteotomy using an undersized compactor drill; group G3, osteotomy using an undersized drill; and group G4, osteotomy using universal osseodensification drills. Two polyurethane blocks were used: block 1, with a medullary portion of 10 pounds per cubic foot (PCF 10) and with a 1 mm cortical portion of PCF 40, and block 2, with a medullary of PCF 15 and with a 2 mm cortical portion of PCF 40. Tapered implants of 4 mm in diameter and 11 mm in length were used. The insertion torque (IT) and ISQ were measured. The dimensions of the final instrument used in each group and the dimensions of the implant were used to calculate the total area of each part, and these data were compared. Results Differences between the four groups were found for IT and ISQ values depending on the technique used for the osteotomy in the two synthetic bone models (p < 0.0001). All groups showed lower values of initial stability in block 1 than in block 2. Conclusions Undersized osteotomies with instruments designed according to the implant body significantly increased the initial stability values compared to beds prepared with universal drills and using the drilling sequence standardized by the manufacturer.

The use of acetabular screws in total hip arthroplasty and its influence on wear and periacetabular osteolysis in the long-term follow-up

Purpose The cementless implantation of hip replacement cups may be performed with and without the additional use of acetabular screws. If the surgeon uses screws or not depends on variable factors. In general, the use of screws is intended to increase the primary stability of the cup. Whether screws increase the initial stability of the cup construct, or even reduce it in part, is the subject of considerable debate in the literature. It is also unclear whether the additional screws lead to increased wear or increased periacetabular osteolysis over the long-term course. Methods Two hundred eleven patients from a previous study with a minimum follow-up of 10.7 years were included. Of these, 68 patients with 82 total hip arthroplasties (THA) were given clinical and radiological follow-up examinations. Of these, 52 had been fitted without screws and 30 with screws. On the basis of radiographs, annual wear and osteolysis were quantified. The clinical results were recorded by means of VAS, HHS, and WOMAC scores. Results Significantly more periacetabular osteolysis was found if additive acetabular screws had been used. No difference was found in relation to the volumetric wear per year. Likewise, no difference was found with regard to the clinical scores. Conclusions The use of additive acetabular screws leads to increased osteolysis in the periacetabular bone stock. Insofar as the primary stability of the cementless cup construct allows it, no additional acetabular screws should be used.

Biomechanical aspects of the initial stability of instrumental fixation in the treatment of subaxial cervical dislocations: an experimental study

Objective. To study the influence of thoracic inlet angle (TIA) and the fracture of the articular process on the initial strength of the fixation of the spinal segment during its anterior and circular instrumental surgical stabilization in an experiment on a model of the lower cervical spinal segment.Material and Methods. The material of the study was assembled models of C6–C7 spinal segments made using addictive technologies by 3D printing. After preliminary instrumentation, spinal segments were installed on the stand testing machine using specially manufactured equipment. A metered axial load simulating the native one was applied along the axis of the parameters SVA COG–C7 and C2–C7 SVA, which values were close to the value of 20 mm, at a rate of 1 mm/min until the shear strain was reached. The system’s resistance to displacement was measured, and the resulting load was evaluated. Four study groups were formed depending on the modeling of the T1 slope parameter, the integrity of the facets, and the type of instrumentation. Three tests were conducted in each group. The graphical curves were analyzed, and the values of the parameters of the neutral and elastic zones, the yield point, time to yield point, and the value of the applied load for the implementation of shear displacement were recorded. The data were subjected to comparative analysis.Results. In Group 1, anterior shear displacement of the C6 vertebra could not be induced in all series. In groups 2, 3, and 4 a shear displacement of ≥4 mm was noted in all series. In Group 3 where a fracture of the articular process was additionally modeled, the average value of the yield point was 423.5 ± 46.8 N. Elastic zone, the time to the onset of the yield point, the time at the end point or at a shear of C6 ≥4 mm did not differ significantly. In Group 4, a translational displacement of ≥4 mm was observed, though the average yield point was 1536.0 ± 40.0 N.Conclusion. The direction of the load applied to the fixed spinal segment, as well as the presence of damage to the articular processes, play a crucial role in maintaining resistance to shear deformation of the spinal segment during its instrumental stabilization. At high values of TIA (T1 slope) and the presence of fractures of the articular processes, the isolated anterior stabilization is less effective, circular fixation of 360° under these conditions gives a high initial stability to the spinal segment.

STUDYING THE INITIAL STABILITY OF A NEW TYPE OF HIP REPLACEMENT- SPIRON SHORT STEM

Objective: we perform this study with the following objective: Studying the initial stability of a new type of hip replacement-spiron short stem. Subjects and methods: Experiments to determine the deformability, elasticity and force capacity of the femur were used for the short stem and the long stem replacement corresponds to the original femur without the prosthesis. Along with that, we were evaluated short-term results of treatment for 70 patients with 92 Spiron hips replacement in the Institute of Trauma and Orthopedic-108 Military Central Hospital, from 2012 to 2016. Results: The analysis results showed that the Spiron short stem prosthetic had a significantly smaller displacement in the mid-frost bond than the Zweymuller long stem prosthesis. Clinical research: Harris’s score was 45.2 (± 2.4) before surgery. At the final examination time Harris’s score was 91.4 (± 2.5). The rate: very good (75.0%), good (17.4%), average (3.3%), poor (4.3%). There are 02 cases early stem loosening had to stem revision surgery (2.2%). Conclusion: These results show the good initial fixed ability as well as stability when replaced by the Spiron stem.

A New Technique of Two Iliac Cortical Bone Blocks Sandwich Technique for Secondary Alveolar Bone Grafting in Cleft Lip and Palate Patients

Alveolar cleft bone graft in the second stage of surgery was a crucial part of the cleft palate treatment protocol with many advantages: reconstructing bone for tooth eruption, supporting the periodontal structure for the teeth adjacent to the cleft, supporting and lifting the arch and preventing from collapsing of maxillary arch. Grafting technique and material are selected based on the treatment purpose that for orthodontic moving tooth into the arch or for dental implant rehabilitation. Cancellous material provides rapid vascularization and healing facilitating for tooth moving into the cleft site but easy to resorb that unsuitable for dental implant placement. While dense material is difficult to move teeth into the cleft but increase initial stability. Therefore, we offered a method that limit bone resorption, easily obtain the implant initial stability, quick osseointegration called two iliac cortical bone blocks sandwich technique for a purposes of dental implant rehabilitation. Treatment protocol started with orthodontic treatment prior alveolar bone grafting to create proper space for implant restoration. Our clinical experience with 32 cleft sites using two iliac cortical bone blocks sandwich had shown potential clinical application in follow-up time up to 96 months. Evaluation criteria of bone grafting for alveolar cleft included soft tissue condition of graft area, nasal fistula closure, bone grafting outcome, success in osseointegration and implant prosthesis. This chapter described in detail treatment procedure and outcomes of a new technique of two iliac cortical bone blocks sandwich for alveolar cleft in patients with unilateral cleft palate.

Finite element simulation and statistical investigation of an orthodontic mini-implant’s stability in a novel screw design

One of the essential aspects of the mini-implant’s successful application is its stability after being installed in the bone. The stability of the mini-implant affected the most by its geometry. In the present research, the effect of the geometry-related parameters of the mini-implant on its lateral displacement is investigated by Finite Element (FE) modeling using ABAQUS software. The parameters studied include length, diameter, pitch, and depth of the screw threads; besides, length and angle of the conical section. The Taguchi method was used to prevent many experiments. The mesh convergence tests and experimental tests confirmed the FE model quantitatively and qualitatively. Mean of means and variance analysis determined the parameters significance and their contribution on the stability. The screw diameter and length have the most contribution to mini-implant’ displacement. The effect of screw pitch was less than that for length and diameter. The conical section improved the initial stability by creating compressive stress and additional friction in its surrounding bone. No significant effects on the stability of the mini-implant have been observed for the non-threaded part. By examining the effect of thread depth on its stability by defining the ratio of thread depth to the internal diameter and to maintain the strength of the screw the optimal value for internal to external ratio is set at about 0.7.