New non-destructive testing approach based on eddy current for crack orientation detection and parameter estimation

Crack orientation is a vital factor in the behavioral study of fractures, especially the study of crack propagation in structures that are under dynamic or fatigue loading. Indeed, many non-destructive testing (NDT) techniques have been developed recently for the detection of cracks such as the eddy current testing (ECT). However, the crack orientation has not been undertaken into consideration. In this paper, a NDT based on eddy current using 3D finite element modeling, is proposed for the determination of the crack orientation. The idea of this proposed technique benefits from the influences of crack orientation, which can be observed on the components of eddy current and the related magnetic flux density following the x, y axes, for the estimation of the crack angle orientation based on an interpolation criteria. The obtained results through the presented simulation prove the validity of the proposed technique for the detection of crack angle orientation.

SIMULASI PENGARUH ORIENTASI SUDUT SERAT TERHADAP TEGANGAN TARIK LAMINATED COMPOSITE

Composite is a material consisting of a mixture or combination of two or more materials, either micro or macro, where the properties of the material are different in shape and chemical composition from the original substance. In this study, the composite was tested to determine the tensile strength using simulation. Composite material modeling consists of carbon fiber as reinforcement and epoxy resin as the matrix. Then the composite material was given a uniaxial loading with a loading value of 50 N. By using variations in the orientation of the fiber angle 45ᵒ/90ᵒ/-45ᵒ, 45ᵒ/90ᵒ/-45ᵒ and 60ᵒ/45ᵒ/-60ᵒ. This study aimed to determine the effect of fiber angle orientation on tensile strength, maximum deformation and location of maximum stress on carbon fiber composites. The best composite design is the composite with fiber angle orientation of 45ᵒ/90ᵒ/-45ᵒ with a tensile stress value of 3.6 MPa and the smallest deformation of 0.0644 mm.

Muon Tracker with Unsegmented Plastic Scintillator Panels

A muon tracker was developed using three polyvinyl toluene scintillator panels instrumented with photomultiplier tubes (PMTs) mounted at the corners. Panels are mounted in parallel on an aluminum frame which allows for simple adjustment of angle, orientation and separation distance between the panels. The responses of all PMTs in the system are digitized simultaneously at sub-nanosecond sample spacing. Software was developed to adjust settings and implement event rejection based on the number of panels that detected a scintillation event within a 400-nanosecond record. The relative responses of the PMTs are used to calculate the position of scintillation events within each panel. The direction of the muons through the system can be tracked using the panel strike order. Methods for triangulation by both time-of-flight (TOF) and PMT magnitude response are reported. The time triangulation method is derived and experimentally demonstrated using parallel cables of differing length. The PMTs used in this experiment are only optimized for amplitude discrimination, not for time spread jitter as would be required to implement TOF methods into the scintillator panels. A Gaussian process regression machine learning tool was implemented to learn the relationship between PMT response features and positions from a calibration dataset. Resolution is analyzed using different numbers of PMTs and low-versus-high PMT sensitivities. Muons traveling in forward and reverse directions through the detector system were counted in all six axis orientations. The muon detector was deployed for 28 days in an underground tunnel and vertical muon counts were recorded.

Microstructural and Mechanical Properties of the Anterolateral Ligament of the Knee

Background: The variable anatomy and controversy of the anterolateral ligament (ALL) reflect the complex relationship among the anterolateral knee structures. Purpose/Hypothesis: The purpose was to quantify the microstructural and mechanical properties of the ALL as compared with the anterolateral capsule (ALC) and lateral collateral ligament (LCL). The primary hypotheses were that (1) there is no difference in these properties between the ALL and ALC and (2) the LCL has significantly different properties from the ALL and ALC. Study Design: Descriptive laboratory study. Methods: The LCL, ALL, and ALC were harvested from 25 cadaveric knees. Mechanical testing and microstructural analyses were performed using quantitative polarized light imaging. The average degree of linear polarization (AVG DoLP; mean strength of collagen alignment) and standard deviation of the angle of polarization (STD AoP; degree of variation in collagen angle orientation) were calculated. Results: Linear region moduli were not different between the ALC and ALL (3.75 vs 3.66 MPa, respectively; P > .99). AVG DoLP values were not different between the ALC and ALL in the linear region (0.10 vs 0.10; P > .99). Similarly, STD AoP values were not different between the ALC and ALL (24.2 vs 21.7; P > .99). The LCL had larger modulus, larger AVG DoLP, and smaller STD AoP values than the ALL and ALC. Of 25 knee specimens, 3 were observed to have a distinct ALL, which exhibited larger modulus, larger AVG DoLP, and smaller STD AoP values as compared with nondistinct ALL samples. Conclusion: There were no differences in the mechanical and microstructural properties between the ALL and ALC. The ALC and ALL exhibited comparably weak and disperse collagen alignment. However, when a distinct ALL was present, the properties were suggestive of a ligamentous structure. Clinical Relevance: The properties of the ALL are similar to those of a ligament only when a distinct ALL is present, but otherwise, for the majority of specimens, ALL properties are closer to those of the capsule. Variability in the ligamentous structure of the ALL suggests that it may be more important in some patients than others and reconstruction may be considered in selective patients. Further study is needed to better understand its selective role and optimal indications for reconstruction.

Mechanical Strength of Bamboo Filled PLA Composite Material in Fused Filament Fabrication

Through the past two decades, there has been a continued push for renewable resources and future sustainability of materials and processes. This has prompted more developments of providing environmentally friendly practices and products, both in terms of higher recyclability and greater use of renewable resources. An important area of interest are materials for construction and manufacturing purposes, specifically “green” sustainable reinforcement materials for thermoplastic composite materials. During this time, there has also been an evolution in manufacturing methods. Additive manufacturing (AM) has continued to grow exponentially since its inception for its extensive benefits. This study aims to investigate an additive manufactured composite material that is a greener alternative to other composites that are not reinforced by natural fibers. A bamboo filled polylactic acid (PLA) composite manufactured by fused filament fabrication was evaluated in order to gather mechanical strength characteristics by means of tensile, flexure, compression, impact, and shear tests. In this material, the bamboo reinforcing material and the PLA matrix material can both be sourced from highly renewable resources. In this study, a variety of test samples were manufactured at different manufacturing parameters to be used for mechanical testing. The results were recorded with respect to varying manufacturing parameters (raster angle orientation). It was found that the 0° raster angle orientation performed the best in every category except tensile. Additively manufactured bamboo filled PLA was also seen to have comparable strength to certain traditionally manufactured bamboo fiber reinforced plastics.