Enhancement of physical and mechanical properties of polyamide 66 fibers using polysiloxane‐functionalized multi‐walled carbon nanotubes

2020 ◽  
Vol 138 (14) ◽  
pp. 50170
Author(s):  
Jiao Zhang ◽  
Wenguang Yu ◽  
Xianye Zhang ◽  
Xuefeng Gao ◽  
Haihui Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Physical And Mechanical Properties ◽  
Polyamide 66 ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

scholarly journals Fabrication and Characterization of Polylactic Acid Electrospun Scaffolds Modified with Multi-Walled Carbon Nanotubes and Hydroxyapatite Nanoparticles

Biomimetics ◽  
2020 ◽  
Vol 5 (3) ◽  
pp. 43
Author(s):  
Athanasios Kotrotsos ◽  
Prokopis Yiallouros ◽  
Vassilis Kostopoulos
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Polylactic Acid ◽  
Physical And Mechanical Properties ◽  
Polymeric Materials ◽  
Cost Effective ◽  
Electrospinning Process ◽  
Wide Range ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

The solution electrospinning process (SEP) is a cost-effective technique in which a wide range of polymeric materials can be electrospun. Electrospun materials can also be easily modified during the solution preparation process (prior SEP). Based on this, the aim of the current work is the fabrication and nanomodification of scaffolds using SEP, and the investigation of their porosity and physical and mechanical properties. In this study, polylactic acid (PLA) was selected for scaffold fabrication, and further modified with multi-walled carbon nanotubes (MWCNTs) and hydroxyapatite (HAP) nanoparticles. After fabrication, porosity calculation and physical and mechanical characterization for all scaffold types were conducted. More precisely, the morphology of the fibers (in terms of fiber diameter), the surface properties (in terms of contact angle) and the mechanical properties under the tensile mode of the fabricated scaffolds have been investigated and further compared against pristine PLA scaffolds (without nanofillers). Finally, the scaffold with the optimal properties was proposed as the candidate material for potential future cell culturing.

scholarly journals NICKEL-BASED MULTIWALLED CARBON NANOTUBE COMPOSITE COATINGS

2018 ◽  
Vol 56 (3B) ◽  
pp. 144
Author(s):  
Bui Hung Thang ◽  
Nguyen Xuan Toan ◽  
Nguyen Viet Phuong ◽  
Tran Van Hau ◽  
Nguyen Thi Hong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Composite Coatings ◽  
Physical And Mechanical Properties ◽  
Multiwalled Carbon ◽  
Nickel Electrodeposition ◽  
Multi Walled Carbon Nanotubes ◽  
Carbon Nanotube Composite ◽  
Walled Carbon Nanotubes

Carbon nanotubes (CNTs) have been widely known as nanomaterials with excellent mechanical properties. Previous studies reported that the tensile strength of multi-walled carbon nanotubes (MWCNTs) was up to 63 GPa and single-walled carbon nanotubes (SWCNTs) could reach 150 GPa while the highest tensile strength of the steel was found to be about 1.8 GPa. SWCNTs could have Young’s modulus up to 1000 GPa that was much greater than the value of 209 GPa of steel. Therefore, there is a great potential to utilize CNTs as reinforced materials for composites in general and Ni electrodeposition coating in particular to improve hardness, durability, corrosion, and other physical and mechanical properties. This paper presents results of preparing and examining characteristics of the Nickel electrodeposition coatings containing MWCNTs (Ni-MWCNTs). The Ni-MWCNTs composite coatings deposited on a steel plate with the area of 0.4 dm2 using bipolar pulses at 470 Hz and 50oC in a 5-liter bath. Amount of CNTs varying from 1 g/l to 3 g/l was dispersed into the solution by using surfactants and ultrasonic vibration. CNTs used in the study was MWCNTs diameters in the range from 20 to 90 nanometers and few micrometers in length. The SEM, EDS, hardness and adhesion tests were conducted to analyze the properties of the electrodeposition coatings. The obtained results indicated that the hardness and adhesion of the Ni-CNTs coating were 1.5 and 1.46 times, respectively, higher than those of the Ni coating. In addition, adhesion of the Ni-CNTs coating was significantly improved.

scholarly journals Enhancement of out-of-plane mechanical properties of carbon fiber reinforced epoxy resin composite by incorporating the multi-walled carbon nanotubes

2021 ◽  
Vol 3 (6) ◽  
Author(s):  
Seyed Ali Mirsalehi ◽  
Amir Ali Youzbashi ◽  
Amjad Sazgar
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Tensile Test ◽  
Epoxy Resin ◽  
Laminate Composite ◽  
Filament Winding ◽  
Hybrid Nanocomposites ◽  
Out Of Plane ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

AbstractIn this study, epoxy hybrid nanocomposites reinforced by carbon fibers (CFs) were fabricated by a filament winding. To improve out-of-plane (transverse) mechanical properties, 0.5 and 1.0 Wt.% multi-walled carbon nanotubes (MWCNTs) were embedded into epoxy/CF composites. The MWCNTs were well dispersed into the epoxy resin without using any additives. The transverse mechanical properties of epoxy/MWCNT/CF hybrid nanocomposites were evaluated by the tensile test in the vertical direction to the CFs (90º tensile) and flexural tests. The fracture surfaces of composites were studied by scanning electron microscopy (SEM). The SEM observations showed that the bridging of the MWCNTs is one of the mechanisms of transverse mechanical properties enhancement in the epoxy/MWCNT/CF composites. The results of the 90º tensile test proved that the tensile strength and elongation at break of nanocomposite with 1.0 Wt.% MWCNTs improved up to 53% and 50% in comparison with epoxy/CF laminate composite, respectively. Furthermore, the flexural strength, secant modulus, and elongation of epoxy/1.0 Wt.% MWCNT/CF hybrid nanocomposite increased 15%, 7%, and 9% compared to epoxy/CF laminate composite, respectively.

Sign in / Sign up

Export Citation Format

Share Document