Effect of Pineapple Leaf Fiber Volume Fraction with 157 BQTN-EX as a Matrix on the Tensile Strength of the Composite

2021 ◽  
pp. 247-252
Author(s):  
Muhammad ◽  
Reza Putra ◽  
T. Hafli ◽  
Asnawi
Keyword(s):  
Tensile Strength ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Fiber Volume ◽  
Pineapple Leaf Fiber ◽  
Leaf Fiber

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

scholarly journals Tensile Mechanical Properties and Failure Modes of a Basalt Fiber/Epoxy Resin Composite Material

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Jingjing He ◽  
Junping Shi ◽  
Xiaoshan Cao ◽  
Yifeng Hu
Keyword(s):  
Tensile Strength ◽  
Composite Material ◽  
Fiber Volume Fraction ◽  
Failure Modes ◽  
Volume Fraction ◽  
Basalt Fiber ◽  
Orientation Angle ◽  
Fiber Volume ◽  
Fiber Clustering ◽  
Fiber Orientation Angle

Uniaxial tensile tests of basalt fiber/epoxy (BF/EP) composite material with four different fiber orientations were conducted under four different fiber volume fractions, and the variations of BF/EP composite material failure modes and tensile mechanical properties were analyzed. The results show that when the fiber volume fraction is constant, the tensile strength, elastic modulus, and limiting strain of BF/EP composite material all decrease with increasing fiber orientation angle. When the fiber orientation angle is constant, the tensile strength, elastic modulus, and limiting strain of BF/EP composite material all increase with increasing fiber volume fraction. A certain degree of fiber clustering appears in the epoxy resin when the basalt fiber volume fraction is >1.2%. The fiber equidistribution coefficient and clustering fiber content were used to characterize the basalt fiber clustering effect. With the increase of fiber volume fraction, the clustering fiber content gradually increased, but the fiber equidistribution coefficient decreased. Meanwhile, based on Tsai theory, a geometric model and a tensile mechanical model of the clustering fiber are established. By considering the fiber clustering effect, the BF/EP composite material tensile strength is calculated, and the calculated values are close to the experimental results.

scholarly journals Tensile Behavior Characteristics of High-Performance Slurry-Infiltrated Fiber-Reinforced Cementitious Composite with Respect to Fiber Volume Fraction

Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3335 ◽  
Author(s):  
Seungwon Kim ◽  
Dong Joo Kim ◽  
Sung-Wook Kim ◽  
Cheolwoo Park
Keyword(s):  
Tensile Strength ◽  
Energy Absorption ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Absorption Capacity ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Energy Absorption Capacity ◽  
Direct Tensile ◽  
Direct Tensile Strength

Concrete has high compressive strength, but low tensile strength, bending strength, toughness, low resistance to cracking, and brittle fracture characteristics. To overcome these problems, fiber-reinforced concrete, in which the strength of concrete is improved by inserting fibers, is being used. Recently, high-performance fiber-reinforced cementitious composites (HPFRCCs) have been extensively researched. The disadvantages of conventional concrete such as low tensile stress, strain capacity, and energy absorption capacity, have been overcome using HPFRCCs, but they have a weakness in that the fiber reinforcement has only 2% fiber volume fraction. In this study, slurry infiltrated fiber reinforced cementitious composites (SIFRCCs), which can maximize the fiber volume fraction (up to 8%), was developed, and an experimental study on the tensile behavior of SIFRCCs with varying fiber volume fractions (4%, 5%, and 6%) was carried out through direct tensile tests. The results showed that the specimen with high fiber volume fraction exhibited high direct tensile strength and improved brittleness. As per the results, the direct tensile strength is approximately 15.5 MPa, and the energy absorption capacity was excellent. Furthermore, the bridging effect of steel fibers induced strain hardening behavior and multiple cracks, which increased the direct tensile strength and energy absorption capacity.

scholarly journals Influence of MgO and Hybrid Fiber on the Bonding Strength between Reactive Powder Concrete and Old Concrete

2016 ◽  
Vol 2016 ◽  
pp. 1-13 ◽  
Author(s):  
Mo Jinchuan ◽  
Ou Zhongwen ◽  
Wang Yahui
Keyword(s):  
Tensile Strength ◽  
Bonding Strength ◽  
Fiber Volume Fraction ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Drying Shrinkage ◽  
Splitting Tensile Strength ◽  
Reactive Powder Concrete ◽  
Fiber Volume ◽  
Reactive Powder

The reactive powder concrete (RPC) was used as concrete repair material in this paper. The influence of steel fiber, steel fiber + MgO, and steel fiber + MgO + polypropylene fiber (PPF) on the mechanical properties of RPC repair materials and the splitting tensile strength between RPC and old concrete was studied. Influences of steel fiber, MgO, and PPF on the splitting tensile strength were further examined by using scanning electronic microscopy (SEM) and drying shrinkage test. Results indicated that the compressive and flexural strength was improved with the increasing of steel fiber volume fraction. However, the bonding strength showed a trend from rise to decline with the increasing of steel fiber volume fraction. Although MgO caused mechanical performance degradation of RPC, it improved bonding strength between RPC and existing concrete. The influence of PPF on the mechanical properties of RPC was not obvious, whereas it further improved bonding strength by significantly reducing the early age shrinkage of RPC. Finally, the relationship of drying shrinkage and splitting tensile strength was studied, and the equation between the splitting tensile strength relative index and logarithm of drying shrinkage was obtained by function fitting.

scholarly journals Experimental Investigation on the Quasi-Static Tensile Capacity of Engineered Cementitious Composites Reinforced with Steel Grid and Fibers

Materials ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 2666
Author(s):  
Li ◽  
Liu ◽  
Wu ◽  
Wu ◽  
Wu
Keyword(s):  
Tensile Strength ◽  
Energy Dissipation ◽  
Ultimate Tensile Strength ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Kevlar Fiber ◽  
Static Tensile ◽  
Pva Fiber

An engineered cementitious composite (ECC) was reinforced with a steel grid and fibers to improve its tensile strength and ductility. A series of tensile tests have been carried out to investigate the quasi-static tensile capacity of the reinforced ECC. The quasi-static tensile capacities of reinforced ECCs with different numbers of steel-grid layers, types of fibers (Polyvinyl alcohol (PVA) fiber, KEVLAR fiber, and polyethylene (PE) fiber), and volume fractions of fibers have been tested and compared. It is indicated by the test results that: (1) On the whole, the steel grid-PVA fiber and steel grid-KEVLAR fiber reinforced ECCs have high tensile strength and considerable energy dissipation performance, while the steel grid-PE fiber reinforced ECC exhibits excellent ductility. (2) The ultimate tensile strength of the reinforced ECC can be improved by the addition of steel grids. The maximal peak tensile stress increase is about 50–95% or 140–190% by adding one layer or two layers of steel grid, respectively. (3) The ultimate tensile strength of the reinforced ECC can be enhanced with the increase of fiber volume fraction. For a certain kind of fiber, a volume fraction between 1.5% and 2% grants the reinforced ECC the best tensile strength. Near the ultimate loading point, the reinforced ECC exhibits strain hardening behavior, and its peak tensile stress increases considerably. The energy dissipation performance of the reinforced ECC can also be remarkably enhanced by such an increase in fiber volume fraction. (4) The ductility of the steel grid-PVA fiber reinforced ECC can be improved by the addition of steel grids and the increase of fiber volume fraction. The ductility of the steel grid-KEVLAR fiber reinforced ECC can be improved by the addition of steel grids alone. The ductility and energy dissipation performance of the steel grid-PE fiber reinforced ECC can be improved with the increase of fiber volume fraction alone. A mechanical model for the quasi-static initial and ultimate tensile strength of the steel grid-fiber reinforced ECC is proposed. The model is validated by the test data from the quasi-static tension experiments on the steel grid-PE fiber reinforced ECC.

scholarly journals Tensile Strength and Density Evaluation of Composites from Waste Cotton Fabrics and High-Density Polyethylene (HDPE): Contributions to the Composite Industry and a Cleaner Environment

2021 ◽  
Vol 1 (1) ◽  
pp. 41-47
Author(s):  
Sri Mulyo Bondan Respati ◽  
Helmy Purwanto ◽  
Ilham Fakhrudin ◽  
Pungkas Prayitno
Keyword(s):  
Tensile Strength ◽  
Textile Industry ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Cotton Fabrics ◽  
Test Results ◽  
Fiber Volume ◽  
Waste Cotton Fabrics ◽  
Density Evaluation ◽  
Straight Fiber

The growth of the textile industry and the massive use of plastic-based materials create economic growth, but it produces waste from post-use, such as clothing waste from cotton fabrics and HDPE that can be recycled and combined as composite materials. Therefore, an experiment was carried out to investigate and analyze the effect of the fiber volume fraction of waste cotton fabric (1.5%, 3.5%, 4.5%, 6%, and 7.5%) with straight fiber arrangement on the tensile strength and density. From the test results, a tensile strength of 178.4 MPa and 182.6 MPa was obtained for yield and max stress, respectively at a fiber volume fraction of 7.5%. Meanwhile, the highest density of 0.95 g/cm3 was obtained at 1.5% fiber volume fraction. The fracture macroscopic view of the specimen shows a resilience fracture (uneven and appears stringy). Although the strength of this composite cannot yet compete with the new composite material, it has a decent environmental contribution. Considering the availability of waste cotton fabrics and HDPE, it promises to be produced as a low-strength composite for construction, ornamentation, or coatings.

scholarly journals UTILIZATION OF VOLUME COMPOSITE FRACTION IN KEPOK BANANA STEM (MASSA PARADISIACA) RANDOM CORNER ORIENTATION WITH POLYESTER MATRIX AGAINST THE MECHANICAL CHARACTERISTIC

2020 ◽  
Vol 1 (1) ◽  
pp. 28-35
Author(s):  
Basuki Widodo ◽  
Anang Subardi
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Average Energy ◽  
Fiber Volume ◽  
Energy Value ◽  
Average Impact ◽  
Polyester Matrix ◽  
Banana Stem

This study aims to determine the effect of volume fraction (10%, 20%, 30%, 40%, 50%) of composite banana stem fiber with polyester matrix on tensile strength and impact strength. From the results of the study obtained an average strength value the most optimal tensile is found in the 10% fiber volume fraction and 90% matrix that is 51.863 N/mm2 and strain value 5.754 N/mm2. As for the lowest tensile strength at 20% fiber volume fraction and 80% matrix that is 36.356 N/mm2 and strain value 7.796%. The composite which has the highest average energy and impact value is the 50% volume fraction matrix 50% has an absorption rate with an average absorbed energy value of 0.8093 Joules and an average Impact Price of 0.0101 Joules / mm2, while the lowest in the volume fraction of 20%, 80% matrix with an average energy value of 0.4129 Joules and an average Impact Price of 0.0052 Joules/mm2. It can be concluded that the addition of fiber volume fraction affects the tensile strength and impact strength.

scholarly journals Variation of the Mechanical Properties for Natural Fiber Reinforced Composites with Different Weight Ratio of Ziziphus Nummularia’s (Ber) Fibers

2020 ◽  
Vol 8 (6) ◽  
pp. 5393-5397
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Fiber Volume Fraction ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Natural Fibers ◽  
Weight Ratio ◽  
Young Modulus ◽  
Fiber Volume

In the present era, Natural fibers are favored for the formation of composites due to their low density, high strength, biodegradability, easy production, low carbon foot, environment friendly nature in comparison of synthetic fibers. This Paper deals with NFRC made from natural fibers obtained from the plants of arid region of Western Rajasthan on which a few researchers are focusing. This paper discuss on the extraction process of fiber from the ber’s stems, manufacturing of composites by using epoxy resin & ber’s fibers then testing of its mechanical properties e.g. tensile strength, young modulus, yield strength , and percentage elongation. Six Sample were made having weight ratio - 0.1, 0.2, 0.3, 0.4, 0.45, & 0. 6. Dog bone samples were prepared according to the ASTM D638 (Type IV) standard. Tensile strength varies from 12.19 MPa to 25 MPa, while young modulus varies from 1.4GPa to 2.9GPa for different weight ratios. Yield strength varies from 10.77 MPa to 21.16 MPa. Percentage of Elongation varies from 1 to 3%. These results shows that ber’s stems can be used for fiber extraction to manufacture composites materials & for better mechanical properties minimum fiber volume fraction percentage is 13% and maximum fiber fraction is 31%.This data can be used further when optimum value of fiber volume fraction is required to form composites from ber’s fibers.

scholarly journals The Influence of Pineapple Leaf Fiber Orientation and Volume Fraction on Methyl Methacrylate-Based Polymer Matrix for Prosthetic Socket Application

Polymers ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 3381
Author(s):  
Eric Worlawoe Gaba ◽  
Bernard O. Asimeng ◽  
Elsie Effah Kaufmann ◽  
E. Johan Foster ◽  
Elvis K. Tiburu
Keyword(s):  
Carbon Fiber ◽  
Methyl Methacrylate ◽  
Fiber Orientation ◽  
Load Transfer ◽  
Volume Fraction ◽  
Fiber Volume ◽  
Pineapple Leaf Fiber ◽  
Prosthetic Socket ◽  
Limb Load ◽  
Leaf Fiber

This work reports on the use of low-cost pineapple leaf fiber (PALF) as an alternative reinforcing material to the established, commonly used material for prosthetic socket fabrication which is carbon-fiber-reinforced composite (CFRC) due to the high strength and stiffness of carbon fiber. However, the low range of loads exerted on a typical prosthetic socket (PS) in practice suggests that the use of CFRC may not be appropriate because of the high material stiffness which can be detrimental to socket-limb load transfer. Additionally, the high cost of carbon fiber avails opportunities to look for an alternative material as a reinforcement for composite PS development. PALF/Methyl Methacrylate-based (MMA) composites with 0°, 45° and 90° fiber orientations were made with 5–50 v/v fiber volume fractions. The PALF/MMA composites were subjected to a three-point flexural test to determine the effect of fiber volume fraction and fiber orientation on the flexural properties of the composite. The results showed that 40% v/v PALF/MMA composite with 0° fiber orientation recorded the highest flexural strength (50 MPa) and stiffness (1692 MPa). Considering the average load range exerted on PS, the flexural performance of the novel composite characterized in this work could be suitable for socket-limb load transfer for PS fabrication.

Sign in / Sign up

Export Citation Format

Share Document